All Products

Reproduction concours correct firewall ground wire for the Mercury Cougar. For use on 390 and 428 Cobra Jet Cougars. You can find the small block version here. This strap features the correct part number and markings. It is little details like this that will often separate 1st and 2nd place at the show.Ford part # C8WB-14303-A. ...

Ground wire for convertible pump motor. Short wire section that attaches to the pump motor and grounds to the chassis of any 1969-73 Mercury Cougar or Ford Mustang. Easy to copy, #10 gauge wire about 11-1/2 inches long. Two ring terminals attached. Easy peasy.

Used factory ground wire for the windshield wiper motor on any 1968 Mercury Cougar or Ford Mustang. Bullet connector plug and ground loop that mounts to bracket. Marked C8ZB-19C661-A.

This is a reproduction of the original orange engine displacement decal that features black lettering and black and white checkerboard on each end. This decal was used on the top of the air cleaner lid on GT-E models.Fits:1968 Mercury Cougar ...

Emissions decal for the 427 4V in the 1968 Mercury Cougar GT-E.Replaces Ford Part #: C8AE-9C485-C. 

This listing is for all six pieces restored and of course requires you send your cores in advance. It can take anywhere from 1 to 4 months depending on what time of year it is and where we are in our cycle with our plater as we send a minimum of $20k in at a time. We make sure they are separated from the more common parts we have and these are treated with special care every step of the way. On this particular set we never ask them to hurry. Do know that if you have extra holes drilled they...

This complete set of grille bars have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no scrapes so as to qualify for...

This pair of tail light bezels have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.  If you send cores in for exchange they must be pit free and no scrapes so as to...

Features 274 pages / 750 photos/ 12,300 items / history / finishes / measuring and more. This book provides detailed information about the fasteners specified in assembly manuals and parts books. All 12,300 fasteners are referenced to a photo! Must have for anyone wanting to correctly put together a 1955-1973 FoMoCo product.

This reproduction 2 1/4" Tri-Y H pipe to be used with the Patriot style headers on your 1970 Cougar or Mustang.

This reproduction 2 1/4" Tri-Y H pipe to be used with the Scott Drake style headers on your 1970 Cougar or Mustang.

This reproduction 2" Tri-Y H pipe to be used with the Patriot style headers on your 1969 Cougar or Mustang.

This reproduction 2" Tri-Y H pipe to be used with the Scott Drake style headers on your 1969 Cougar or Mustang.

This direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang equipped with either the 289 or 302 engine and stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 289 or 302 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with either the H, M, or Q code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351 Cleveland engines. Please...

This direct replacement is the 2-1/4 inch H pipe only, and is for any 1970 Mercury Cougar or Ford Mustang with stock 2V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and custom made for dual exhaust on any 1970 Cougar and Mustang with the 2 barrel H code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351W, 1970 351C-4V, or 1971-73 Cleveland...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock 4V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 4 barrel M code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351C-2V, or 1971-73 Cleveland...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1969-70 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1969-70 Cougars and Mustangs with the 351W engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Cleveland engines. Please allow 2 - 3 weeks for delivery. ...

This direct replacement is the 2 inch H pipe only and is for any 1969 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1969 Cougar and Mustang with the 390 engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

Direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2 inch...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1968-69 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1968-69 Cougars and Mustangs with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the passenger side spacer. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please...

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1968-69 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from original 1968-69 Cougars and Mustangs with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the...

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the spacer on the passenger side. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1971 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 429CJ engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery.

This direct replacement is the 2-1/2 inch H pipe only and is for any 1969-70 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar Eliminator and Boss Mustang  with the G code Boss 302 engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.

Reproduction replacement halogen bulb for your headlights. This is a clear bulb, "natural white" alternative to the "cool white" bulbs included in our halogen headlight conversion kit. 55 Watt Xenon Halogen H4/9003 bulb. Sold Individually.

Reproduction plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Late 1970 used the same as the 1971-73 model.Replaces Ford part # D0DZ-10718-A.

Used plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Probably introduced at the same time in very late 1969 as when the hold down clip was used to attach to the battery apron? Replaces Ford part # D0DZ-10718-A and casting number D0DB-10755-A. 

NOS emergency / parking brake handle.  To remove your old handle break the plastic off of the shaft to reveal the splined pin. Pull out pin with vise grips and install the new unit.

This reproduction emergency / parking brake handle is an exact reproduction that is made from quality materials and is less prone to cracking than your original. That being said, these still will crack if you pull hard and do not have your hand close to the shaft.  This was a design flaw from day one.  The correct way to apply the brake to reduce the chances of these handles cracking is to split your fingers around the shaft when applying the brake, keeping your fingers close to the...

Used grade "B" emergency / parking brake release handle with bezel and cable for the Mercury Cougar. This unit fits both the Standard and XR7. Our grade "B" piece may have a cracked cable sheath and the chrome on the release handle will be flaking or chipping.   Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web...

Used chrome end for the grab handle found on Mercury Cougar XR7 and several other Lincolns like the Continental MK III. Seldom will these be perfect, most have some pitting on the top sides. Fortunately they can be switched end for end and the pitting side can be installed downward. These units are sold individually.Mercury part # C9MB-5422668-A or D0MB-5422668-A.

Unlike the parts pictured, we only have pitted covers left. At present we have no grade "A" examples. C8MB-5422678-A. Brushed die-cast (with stainless steel look) cover for the chromed grab handle end part number C9MB-5422668-A. These are the smooth or plain ends, the Lincolns used a cover that had scrolling. Used on 1969-70 Mercury Cougar XR7 and various other Lincolns and Mercury full sized cars. These clean up pretty well with steel wool as shown. Keep in mind we have reduced priced...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Good used hanger used only on dual exhaust cars. Rubber will be in usable condition but showing its age. Mounts to the rear of a 'turbo' style muffler. 302, 390, 427, 428CJ - all with dual exhausts. Ford part number C8WY-5260-F. *Later production cars, after 11-1-1967

1971 *351-4V prior to 4-12-1971. 1972 and 1973 351-4V with "Quiet" dual exhaust. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-B. *Early production prior to 4-12-1971.

Shopping list of applications. For all H code 351-2V engine codes with singles exhaust. 1971 *351-4V prior to 4-12-1971. 1972 and 1973 with "Quiet" dual exhaust. Engine designated as a 351-4V on air cleaner lid. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-A. *Early production prior to 4-12-1971.

Good used hanger with detail you will never find in a reproduction part. The part you will receive has not been blasted. Mounts to the rear of a 'turbo' style muffler. Right side bracket. 302, 390, 427, 428CJ - all with dual exhausts. Ford part number C8WY-5260-G. *Later production cars, after 11-1-1967

1971 *351-4V after 4-12-1971. 1971 429 CJ 1972 with "Sporty" dual exhaust. Engine designated as a 351-CJ on air cleaner lid. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-C. *Late production - after April 12, 1971.

For all H code 351-2V engine codes with singles exhaust. Includes 1970 351C or Cleveland engines. Holds the rear of the muffler to the passenger side underside body. Ford part number C9WY-5260-A.

Good used tail pipe hanger with decent rubber still attached. Mounts to the frame on the right side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1970 dual and single exhaust Cougars, all engines. 1970 differs in that the tail pipe clamp was spot welded to the hanger. When you look closely on the 1970 version you will see that there is an alignment hole in the bracket and an alignment tab on the clamp. Also the 1970 version had a less pronounced gusset at...

Bracket and insulator that mounts to the body and the left side of the factory transverse muffler. All 289 engine applications. Ford part number C7WY-5260-A or  C7WY-5260-B. *Trivia - All 1967 Cougars with 289 engines had a single exhaust from the factory. Both the C code 289-2V and A code 289-4V.