All Products

THIS ITEM HAS BEEN DICONTINUED BY THE SUPPLIER.A must for anyone planning to work on their own car. This book contains detailed instructions on disassembly and assembly of all major components. As seen on the front cover, this manual covers multipe makes of vehicles.The 1973 Ford Car Shop Manual is the original manual used by Ford mechanics to guide them through repairs and maintenance. Each section provides information on the operation of major systems, diagnostics, troubleshooting, overhaul,...

Used in the rectangular housing under-dash on both the driver and passenger side. 561 specifications#561 Miniature Bulb Rigid Loop Base - 12.8 Volt 0.97 Amp 12.416 Watt T-3 12.0 MSCP, C-8 Filament Design, Rigid Loop Base. 1,000 Average Rated Hours, 1.72" (43.7mm) Maximum Overall Length (M.O.L.), 0.37" Maximum Outer Diameter (M.O.D.).

This kit contains all the replacement springs and hold down components required to do a professional job on rear drum brakes. Kit includes enough parts for two wheels. This is for the 9 inch drum brakes commonly found on the early 6 cylinder cars with 7-1/4 inch rear ends.*Note - Kit does not include hardware for rear emergency brakes.

Vacuum switch not included. This control switch lever assembly only, for the vacuum and damper door consists of the two lever assembly for the vacuum and cable actuation of the A/C plenums damper doors on Mercury Cougar and Ford Mustang with integral A/C.Ford part # C7ZZ-19B888-A.

Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what...

Exact replacement for your original dryer and should be changed anytime the system is recharged. This stainless steel filter element is the life of your system and stops contaminants from clogging the expansion valve. Painted the correct satin black.

Regardless of which V-8 engine, C7ZA-19972-E is the correct part number. This hose is approximately 20 inches long. Two different crimped ends, smooth and waffle may be the difference between Dearborn and San Jose or 1967 and 1968. Anyone know?The Ford MPC number is C7AZ-19972-A.

New Old Stock A/C drain hose for Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. The best part is that because this is a NOS part, it will fit right the first time and be absolutely correct!Ford part #: C7ZZ-19858-C.

There are 2 manufacturers of these hoses and many places will call them a "concours" hose. Neither manufacturer make an exact replica of the original sight glass hose. The finish of the hose does not match, but the most obvious difference is that the sight glass itself has a hexagon shape instead of a square shape. If you would prefer a good used original, give us a call, we can usually dig one up for you. Remember to remove your coupler between this hose and the dryer, it will be need...

Decent reproduction of the air conditioning sight glass hose for the Mercury Cougar and Ford Mustang. Hose texture is not the same and the sight glass itself is different, but length and fittings are correct. If your sight glass hose is not original or you do not have the 2 piece quick disconnect, you may need to purchase the complete sight glass hose kit. For 100% correct hose, please see our good used sight glass hoses. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A or...

Regardless of which V-8 engine, C8ZA-19835-A or C8ZA-19837-A both can be the correct part number. This hose is approximately 74 inches long. This hose also incorporates the site glass. The Ford MPC # is C8ZA-19835-A or C8ZA-19837-A.

This is actually a kit which includes 2 hoses, 2 o-rings, and a quick connect. When assembled this hose is approximately 78 inches long. The Ford Master Parts Catalog (MPC) kit number is C8OZ-19837-A.Sight Glass Hose to A/C Dryer Hose (Part # D1ZA-19835-A)Sight Glass Hose (Part # D1ZA-19837-A)Sight Glass (Part # SG3, D2AZ-19D695-BK or YF-342) 2 O-Rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6,...

C9ZZ-18A318-A New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang

C9ZZ-18A318-C New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang.Tested and works perfectly. Has attached extension marked C9ZA-18A318-J.

For 1969 Mercury Cougars and Ford Mustangs with the 351W engine. Also 1970 Mercury Cougars and Ford Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-3/8", a clutch diameter of 5-3/16", and an overall thickness of 1-11/16 inches. Whew, say that 5 times fast!Ford part # C9AA-2981-D.

For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C7AA-2981-F.

For 1971-73 Mercury Cougars and Ford Mustangs with the 351W engine manufactured after 10-26-1970. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Ford part # D1OA-2981-A. May also have part numbers D1OA-2981-AA, D1OA-2981-A1A, D1OA-2981-A1B, D1OA-2981-A2A, and D1OA-2981-A2B.

Used pulley and clutch assembly for Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-H.

For 1967-69 Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7SA-2981-A.

For 1967 - 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-11/16", a clutch diameter of 6", and an overall thickness of 1-5/8 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-J.

For 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch. Pulley diameter 6-3/4", clutch diameter 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-G.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6", a clutch diameter of 6", and an overall thickness of 1-3/8 inches. Whew, say that 5 times fast! Ford Part # C9AA-2981-E.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 5-5/16", a clutch diameter of 5-5/16", and an overall thickness of 1-3/8 inches. Ford part # C9AA-2981-E1, may also have part # C9AA-2981-E2.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 5-5/16", a clutch diameter of 5-5/16", and an overall thickness of 1-3/8 inches. Whew, say that 5 times fast!Ford Part # D0VA-2981-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.

Used air conditioning vent for any 1968 Mercury Cougar or Ford Mustang with factory installed A/C. These are different than the 1967 A/C vents. For 1968 the vents detached from the main housing for safety reasons. These were meant to 'break away' in the event of an accident. These attach to the housing with a spring, spring sold separately. Grade A is in limited quantities and will have very good chrome, there will be some minor blemishes found under close scrutiny. B grade versions also...

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, spring is available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19C784-A Register and Bezel. (Bright Finish). Ford casting number on reverse of this piece is C8ZA-19C784. Mustang used a shorter bracket, on the reverse you can see the witness line and...

This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...

This A/C vacuum canister mounts to the passenger side shock tower and controls damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1971-73 Mercury Cougar, 1971-73 Ford Mustang, as well as 1970-71 Ford Torino / Fairlane and Mercury Cyclone Montego, 1970-7? Ford Maverick and Mercury Comet.Replaces Ford part # D0DZ-19A566-A.  

C9ZZ-19B888-A

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.This reproduction A/C vent register with knobs is a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs. *NOTE* Mustang...

Passenger side air conditioning register vent with slight manufacturer blemishes. See photos for details.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish. This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent...

Grade A used passenger side air conditioning vent register for 1967 Ford Mustang with standard (non-deluxe) interiors. This one has the factory pebble grain or camera case finish. Very nice used, only have the one available. We also have several Mustang center vents available with the pebble graining.Replaces Ford part number C7ZA-19893. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site to all. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember when we used to spend hundreds of dollars for "decent" used examples and then take a risk with...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember back in the day when we used to spend hundreds of dollars for "decent" used examples and or take a...

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A. NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

Used Wire lead for the accessory terminal found optionally on 71 - 73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire will be marked with D1AB-14A318-AB

Used actuator for the seat back release on the 1970 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.

C9ZZ-3K505-A Unique for the 1969 Boss 302 Eliminator and Mustang. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head.

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...

Used Alternator Adjusting Arm / 429CJ for the 1971 Mercury Cougar / 1971 Ford Mustang 

1967 289 smog pump adjusting arm, casting number C6OE-9B452-A. Ford part number C6OZ-9B452-A. Application is most Ford and Mercury cars sold new in California in 1966-67. Mercury Cougar only used this thermactor pump adjusting bracket in 1967.                                          ...