All Products

C6AZ-8509-A For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. Thermactor OK on any application. 2 sheaves with a diameter of 5-7/8 inches. Ford casting number C6AE-8509-A. *For year 1967 only > Notes say Prior to 1/9/1967.

Used water pump pulley used on 1970-73 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. This pulley is 5-15/16 inches in diameter. Pulley stamped C9OE-8509-F.

Single sheave pulley 5-15/16 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches.Application:1971 - 1973 351 engines with power steering and A/C. Ford casting number D1AE-8509-AA.Ford Part Number C9OZ-8509-C or D2OZ-8509-A

Single sheave pulley 6-61/64 inches in diameter. This pulley is designed to run on the inner most belt plane next to the water pump. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number D1AE-8509-BA....

Single sheave pulley 6-61/64 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number C9OE-8509-G.  Ford part number C9OZ-8509-D Note:  * The Master Parts...

Fits all 1969 390-4V engines without power accessories. No power steering, no air conditioning, and with a single belt alternator. Single sheave pulley, 6 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.Replaces Ford number C9OE-8509-D. Before 2-17-1969.

C8OZ-8509-D Application for 1968 X code 390-2V engines without air conditioning and without power steering. Single sheave pulley, 6-1/8 inches in diameter. *Note* We have found two versions of this pulley and and neither have a casting number stamped in them and Ford lists no casting number, only a part number. To see the earlier and less common version of the two pulleys, click onto the thumbnail.

C8AZ-8509-A All 390 engines without power accessories. No power steering, no air conditioning, and with a single belt alternator. Single sheave pulley, 7-1/4 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-1/8 inches.Ford casting number C8AE-8A528-B. After 2-17-1969.

C8AZ-8509-D 1969 428 Super Cobra Jet only (V and W code axles), 1970 428CJ and 428SCJ prior to Sept 1, 1969. No air conditioning, power steering permissible. Three sheave pulley, 6-1/8 inches and 7-1/8 inches in diameter pulleys. Ford casting number C8AE-8509-C was originally imprinted in ink, if you look closely between the two bonded together pulleys that make this pulley up you may be able to read the C8AE-8509-A stamped casting number from the two sheave inner pulley.

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with the 351-2V, 351-4V, and BOSS 302 engines. These are bare pumps, stripped of pulleys, canisters, dipsticks, tags, and brackets. Suitable for core rebuilding. Original pumps would have been numbered HBA-CC. This pump has an off center pressure port on the back. Takes the DOZZ-3A697-B reservoir. *NOTE* Core exchange not required.

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...

This is a new old stock windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). Replaces Ford Part #: C9AZ-17664-A.

This is a reproduction of a later service replacement version of the windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). The original Ford part was part number C9AZ-17664-C, which consisted of the pump motor (C9AF-17B616-A) and a retainer (383163-S36), which installs in the 69-70 windshield washer reservoir (C9ZZ-17618-A) or 71-73 windshield washer reservoir (D1TZ-17618-A / D1TZ-17618-B). Replaces Ford Part #: E0AZ-17664-A. ...

Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.

New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D3WB-6528519, Mercury MPC # D3WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D3WB-6528518, Mercury MPC # D3WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527703-A, Mercury MPC # C7WY-6528073-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our 1969 grade "A" rear quarter panel extensions have no obvious dings, scrapes, or warping due to over tightening of studs. However, avoiding the bumper contact dents is impossible. These will have small dents from bumper contact. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528519, Mercury MPC # C9WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our 1970 grade "A" rear quarter panel extensions have no obvious dings, scrapes, or warping due to over tightening of studs. However, avoiding the bumper contact dents is impossible. These will have small dents from bumper contact. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # D0WB-6528519, Mercury MPC # D0WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our 1969 grade "A" rear quarter panel extensions have no obvious dings, scrapes, or warping due to over tightening of studs. However, avoiding the bumper contact dents is impossible. These will have small dents from bumper contact. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528518, Mercury MPC # C9WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our 1970 grade "A" rear quarter panel extensions have no obvious dings, scrapes, or warping due to over tightening of studs. However, avoiding the bumper contact dents is impossible. These will have small dents from bumper contact. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # D0WB-6528518, Mercury MPC # D0WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs only minor repairs to be show quality.  Ford part # C7WB-6527703-A Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528519-A, Mercury MPC # C9WY-6528011-A. Do you have questions about your Cat's factory...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # D0WB-6528519-A, Mercury MPC # D0WY-6528011-A. Do you have questions about your Cat's factory...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs only minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C7WB-6527702-A, Mercury MPC # C9WY-6528072-A. Do you have questions about your Cat's factory...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528518-A, Mercury MPC # C9WY-6528010-A. Do you have questions about your Cat's factory...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # D0WB-6528518-A, Mercury MPC # D0WY-6528010-A. Do you have questions about your Cat's factory...

Reproduction driver side rear quarter extension panel for the 67 - 68 Cougar. This is the panel that the quarter extension mounts to.

Reproduction passenger side rear quarter extension panel for the 67 - 68 Cougar. This is the panel that the quarter extension mounts to.

Cut off a dry Western car in the 1980's and stored in the attic of a barn ever since. Cut large, no rust or previous damage, perfect for the high end car that deserves the very best. Better than NOS as you ger all the factory spot welds, includes PS trunk floor as well. Shipping and crating at reasonable cost, call 503-463-1130 for more info, ask for Don.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" driver (left hand) side rear quarter panel. We ask that you call to discuss condition, price, and cut...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" passenger (right hand) side quarter panel. We ask that you call to discuss condition, price, and cut...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" passenger (right hand) side rear quarter panel. We ask that you call to discuss condition, price, and cut...

Reproduction driver side (left hand) quarter panel skin for the Mercury Cougar. These skins are made in America, but are low quality. These are made for the coupe, but can be made to fit a convertible. The 1969 and 1970 are not the same dimensions from the factory, the 1970 model year increased the wheel opening to allow for the optional larger tire size offered in 1970.  The 1969 wheel opening measures at approximately 29-1/2" while the 1970 unit comes in at approximately 30-1/2". This...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate.This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel.You can find the...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate.This is a "patch" cut, which means that vertically it reaches from the bottom of the panel to about 10" up.You can find the full versions here. ...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if yourrequirements for a cut are are different from what is shown, and often we can accommodate. This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel. You can find...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if yourrequirements for a cut are are different from what is shown, and often we can accommodate. This is a "patch" cut, which means that vertically it reaches from the bottom of the panel to about 10" up. You can find the full versions...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are different from what is shown, and often we can accommodate. This is a "patch" cut, which means that vertically it reaches from the bottom of the panel to about 10" up. You can find the full...

Fits 1968 Standard or XR7. Has a pair of longer screws for the 1968 lower section of the door panel. 

Driver side quarter window slide. This is the 10 1/2" slide that bolts to the inner body of the quarter window area.

Passenger side quarter window slide. This is the 10 1/2" slide that bolts to the inner body of the quarter window area.

Used driver side rear quarter window glass bracket, used for all 1969 and most of 1970. The later 1970 bracket had a D0Z... part number and used a different clip for attaching the window regulator. Good used bracket with all three plastic guides in perfect condition. This bracket is correct for Coupe and Convertible. Engineering # C9ZB-6529945-A Here is the 3M product used to glue the glass to the bracket. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install...