All Products

Grade A used passenger side air conditioning vent register for 1967 Ford Mustang with standard (non-deluxe) interiors. This one has the factory pebble grain or camera case finish. Very nice used, only have the one available. We also have several Mustang center vents available with the pebble graining.Replaces Ford part number C7ZA-19893. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site to all. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember when we used to spend hundreds of dollars for "decent" used examples and then take a risk with...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember back in the day when we used to spend hundreds of dollars for "decent" used examples and or take a...

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A. NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

Used Wire lead for the accessory terminal found optionally on 71 - 73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire will be marked with D1AB-14A318-AB

Used actuator for the seat back release on the 1970 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.

C9ZZ-3K505-A Unique for the 1969 Boss 302 Eliminator and Mustang. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head.

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...

Used Alternator Adjusting Arm / 429CJ for the 1971 Mercury Cougar / 1971 Ford Mustang 

1967 289 smog pump adjusting arm, casting number C6OE-9B452-A. Ford part number C6OZ-9B452-A. Application is most Ford and Mercury cars sold new in California in 1966-67. Mercury Cougar only used this thermactor pump adjusting bracket in 1967.                                          ...

1967 390 smog pump adjusting arm, casting number C7AE-9B452-A. Ford part number C6AZ-9B452-C. Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are the same. Click on images to enlarge.                                       The...

1968 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine), or 1969 Boss 302 (G code Eliminator engine) smog pump adjusting arm, casting number C8OE-9B452-A. Ford part number C8AZ-9B452-B, C8AE-B casting number. Bolts sold separate. *Note - Only cars with manual transmissions received thermactor emissions in 1968.

Reproduction thermactor smog pump adjusting bracket for all 1969 Mercury Cougar Eliminator and 1969 Ford Mustang with Boss 302 engines. Additionally this bracket was also used on 1968 Ford cars with 289 or 302 engines with manual transmissions. Quality made product. Replaces Ford part number C8OE-9B452-A.

Used adjusting bracket for the Thermactor air pump for the Mercury Cougar or Ford Mustang equipped with the 302 Boss engine.Ford part # D0ZZ-9B452-A, casting # D0ZE-9B452-A or D0ZE-9B452-B.

C9AZ-3D600-A Power steering pump adjusting spacer for use without air conditioning. For most 1971 Mercury Cougar or Ford Mustang with 429CJ engines.

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. This fine thread version is hard to keep in stock, consider the 1969-73 course thread version as an alternative. Check out...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

This is an open style air cleaner assembly devoid of any snorkel. We send the tops out for a quality rechrome and we can inform you of what dates we have at any one time (date is stamped on bottom, 2 digits year and month, very faint). Most are happy to use the Mustang K code 289 HiPo reproduction air cleaner assembly we sell, which Mercury used on W code GT-E's with 427's. There's also a reproduction unit available.Ford part # C5ZZ-9600-C, C5ZF-9600-D. ...

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-2V Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. Located on the top of the air cleaner. 13.50" span tip to tip.Fits the following models with a 351 2 barrel Regular Fuel engine: 1973 Cougar 1973 Mustang ...

Nice used California emissions air cleaner assembly, includes base with elbow, snorkel, heat riser and air cleaner lid. Application is any 1967 Mercury Cougar or Ford Mustang with C code 289-2V or A code 289-4V engines with closed emissions as sold in California. Elbow on air cleaner connects to the oil fill cap with a rubber hose. All good parts as shown, thermal switch in air cleaner snorkel may not work, and no we cannot test them.Even if you are not currently running all original parts...

Fits all V8s with oval air cleaner.

A Complete A/C and heater control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Check back often, this type and grade of part is seldom in stock very long.Ford part # C7WA-19980-A.

A Complete A/C heater control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Check back often, this type and grade of part is seldom in stock very long. Ford part # C8WA-19980-A.

A/C and heater control bezel or face plate. Grade A- used condition, standard pebble grain trim. Check back often, this type and grade of part is seldom in stock very long.Bezel only, no levers or switch.Ford part # C7ZA-19C705.

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Current dates: None - Specify...

WOW! How long have we been trying to scrounge up good used pins for restoration? These are identical to what is found on all 1969 Cougar and Mustang Convertibles. They are correct for most of the 1970 model year and even if you are one of the few that own a late 1970 Mustang / Cougar they will work on your car too. These also work on the 1971-1973 Convertibles.The picture below shows the new reproduction on the bottom, used 69-70 in the middle and a 1971-1973 pin at top. //-->WCCC is...

1964-66 Ford and Mercury alternator bracket with air conditioning adjusting pulley. Pulley has new bearing installed. Application is 1964-66 Ford and Mercury full sized cars and Thunderbird. All with 352, 390, 410, 427, or 428 FE engines with air conditioning and without thermactor smog. Pulley has been professionally rebuilt with new bearing in house. Pulley has a few small rust pits, that can be filled and painted by the purchaser. Pulley is straight and true, pulley has Ford casting number...

Reproduction gold dichromate 10 blade alternator fan. Used on Mercury Cougars and Ford Mustangs manufactured after 11/17/1969. Actually this is a Ford part found on most all Ford automobiles from 1970-73. 10 blade alternator cooling fan. Replaces Ford Part #: DOAZ-10A310-B

[No Description Provided]

Replaces Ford Part # D0WY-14305-C & D0WY-14305-A

Older used aluminum intake manifold. Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

7TPF Factory AM radio for any 1967 Galaxie or LTD models. Unknown working condition.

7TPZ Factory AM radio for any 1967 Mustang. OEM Ford wire connectors are as present as shown. We tested it in good working condition.

Used radio from a 1974 Mercury Comet or Ford Maverick. Should fit other years too. This is a mono radio, meaning that it is a single channel radio without stereo. That is the way they were built for the Maverick and Comet cars all the way back to 1970. Both the AM and FM radio bands function properly, selector buttons all work properly, comes with used knobs as shown. The only two defects on this radio are the small crack in the lens (shown in photo), and the cut electrical plug. We have...

New old stock amp gauge for the 1969 Mercury CougarFord part number C8WY-10850 Check out the video below on our new gauge tester: ...

Correct three part, telescoping, round base antenna. Comes with round ridged base gasket.*Customer Feedback* "Aloha Don, The antenna showed up with the rest of the USPS sent items. Got in here in three days. Point of installation of antenna. Tie a string to the plug side of the antenna assembly when pulling out from fender so that you can use the string to pull the new antenna plug back through the fender and into the car. Thought of that after pulling antenna out. I was able to use a flexible...

Used anti rattle pad for the stone guard on the Mercury Cougar. This unit is for the 1970 Mercury Cougar specifically and will not fit any other year. These pads must be used with the 1970 Cougar front bumper mounting brackets and the brackets can identified with the square cut window for mounting this pad. Our pad is sold individually and two are required per car.

Reproduction pair of anti rattle pad for the stone guard used on the Mercury Cougar. This unit is for the 1970 specifically and will not fit any other year. These pads must be used with the 1970 front bumper mounting brackets and the brackets can identified by the square cut window for mounting this pad. Sold in pairs and two are required per car.

Reproduction of the protector felt pad between the spare tire and jack handle for the 68 through 70 Mercury Cougar with styled steel wheels. Used only in conjunction with applications that store the jack components on top of the wheel.

Replaces Ford Part # C8AZ-2B164-A Sold individually

WCCC developed walnut straight grain kit for rimblow horn pad restorations. Fits all Standard / Decor (non-XR-7) 1969 Cougar hardtop and convertibles. All three pieces were carefully plotted on a computer program to account for their unique contoured shape for each individual insert. Detailed instructions included for preparation and installation. We suggest detailing your horn pad plastic insert, prior to applying this wood grain kit for best results. *NOTE* Fits 1969 rimblow horn pad plastic...

WCCC developed burl woodgrain kit for rimblow horn pad restorations. Fits all 1969 Cougar XR7's hardtop and convertibles. All three pieces were carefully plotted on a computer program to account for their unique contoured shape for each individual insert. Detailed instructions included for preparation and installation. We suggest detailing your horn pad plastic insert, prior to applying this wood grain kit for best results. *NOTE* Fits 1969 rimblow horn pad plastic inserts only. Here’s a...