All Products

This is the storage bag that the convertible top cover folds into when the top is in the down position. Ford calls this part the "Folding top dust hood container." It is made from common vinyl top material and is always black. It measures 15"x27" and the bottom portion is sometimes, tapered down to 8". The same design was used for many Ford Products of the day including Torino, Montego and others. Current offering does not have a tapered bottom, it is square. Pictures will show both styles...

New reproduction insert for the Hurst shifter boots. This is designed to protect the integrity and lengthen the life of the rubber boot used to protect Hurst shifters with rectangular arms. After a while, your boot can become stressed and even begin to tear apart when the arm is shifted contantly. You must remove the shifter handle to install the support. You may need to trim into the reinforced area to get a good fit. Installs from the under side of the boot. Check out our video on rebuilding...

Holley fuel filter decal, for Holley equipped cars. Including all 1967-68 S code 390-4V, 1968-70 R and Q code 428 Cobra Jets, 1967 GT-E with W code 427-4V, or 1969-70 G code Boss 302 Eliminators. Concours detail item. C7OE-9155-A. 

Reproduction BOSS 302 MT Emission Decal for the 1969 Mercury Cougar / Ford Mustang

Reproduction BOSS 302 Rev Limiter Decal for the 1969 Mercury Cougar or 1969 Ford Mustang 

Reproduction BOSS 302 Rev Limiter Decal for the 1970 Mercury Cougar or 1970 Ford Mustang 

 Reproduction BOSS 302 Valve Cover Decal for the 1969 - 1970 Mercury Cougar or Ford Mustang

Nice used aluminum intake manifold for 351C-4V and Boss 351 engines. This was a Ford over the counter or Ford dealer performance offering. This manifold was cast by Buddy Bar and looks on modified. Ford number D1ZX-9425-DA, this version allows the use of a square bore carburetor, which is unlike the original Boss 351 Autolite 4300D spreadbore design carburetor. Most enthusiasts were converting to Holley carburetors for performance, which would be perfect for this intake manifold. Dual plane. ...

Rear most convertible top bow #4, from a 1969-70 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached. Bow only, slat brackets sold separately. Ford part number C9ZZ-7651278-A.

Rear most convertible top bow #4, from a 1971-73 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached.   Ford part number D1ZZ-7651278-A.

Used to cushion and protect top vinyl from excessive wear from side rails. Unfortunately none of the reproductions that we have found resemble the OEM pads. OEM pads looked canvas on the under side that goes against the convertible top rails, and what looked like the soft side of a velcro strip on the upper side that makes contact with the convertible top itself. These are still highly recommended as they keep the convertible top rails from rubbing thorough the convertible top. "I found WCCC...

Good used Western part that is not bent or heavily rusted and the left is the same as right. This is the round style and the round and the flat 1971-72 fender braces fully interchange.Ford master part # D3WY-16B134-A.

Support brace between the bottom of the steel lower dash panel and the cowl top. Fits 1969-70 Mercury Cougar and Ford Mustang with either air conditioning or without air conditioning. Ford part number C9ZB-6504672-A.

One end attaches to the right of the brake pedal support, and the other to the dash panel. Original Ford part number C9ZB-6504510.

Sold as pair on exchange or outright. Only cores with minimal corrosion can be considered for exchange. Ford part number C7AZ-6204144-A, casting number as seen on the backside reads C8AB-6204122-B.  Does not include smaller rod for the sun visor tips.  Sold as a pair.

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

Used mounting bracket from a 1967-68 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1967-68 brackets, but this one has a slightly longer stud. Replaces Ford part number C9ZZ-18A456-A.

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1969-70 brackets, but this one has a slightly shorter and pointed stud. Replaces Ford part number C7ZZ-18A456-A.

1967 Cougar and Mustang tubular steel brace. Connects and supports the rear of the air compressor to the factory intake manifold. From what we can tell there is no difference 67 to 68.Ford part # C7ZZ-2889-A.

289 engines without factory air conditioning.

B1967 California emissions low mount alternator bracket for the S code 390-4V engine. Ford casting number C6AE-10156-A, Ford part number C6AZ-10156-A. The early bracket has two extra (for unknown reasons) small holes. Notice this late bracket can be found with both styles of FoMoCo logos.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and...

Bracket mounts to 9 inch third member. Will not have heavy corrosion as found on Midwest and Eastern cars. Not notched like later years of snubbers. Correct for 1967 Mercury Cougar and 1965-67 Ford Mustang. Rubber bumper sold separately - C3AZ-4730-B rubber carrier bumper. Picture - 2007 40th Anniversary show in Carlisle PA. Bill Pratt with "Catvert".

9 inch rear axle snubber for all 1968-73 Mercury Cougar and Ford Mustang. Will work on 1967 9" differential but has slightly different angles as seen by our pictures. Bare bracket, rubber snubber sold separately.

Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Replaces Ford Part #: D0OZ-10757-A.

Bracket tack welded in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang. These are sold individually, these are not side specific. There is also a reproduction version available. Used part cut from a 1967-68 Mercury Cougar, some spot welds will need to be drilled out on your end. Picture shows approximately what you will receive. 

Used cigar / cigarette lighter and ashtray mounting bracket. Mounts behind the dash on 1967-68 Mercury Cougar and Ford Mustang. Holds the cigar or cigarette lighter element, and the ashtray receptacle. 

Driver side convertible frame assembly mounting and pivot bracket for all 1969-70 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Passenger side bracket with attached convertible arm only. Mounts behind the quarter interior panel. Ford part number C9ZZ-7653119-A.

Passenger side convertible frame assembly mounting and pivot bracket for all 1969-70 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Passenger side bracket with attached convertible arm only. Mounts behind the quarter interior panel. Ford part number C9ZZ-7653118-A.

Detachable mounting plate for installing the driver side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A19-A.

Used bracket for installing the rear interior panels on any 1971-73 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. Replaces Ford part number D1ZZ-76310A84-A. 

These courtesy light brackets are located on the very outer right and left under the dash. Typically this bracket is found on the passenger side of 1967-68 Mercury Cougar and Ford Mustang without air conditioning. This is the long style bracket. There is also a short style for both the driver and passenger side courtesy light. If you have factory air conditioning you would want the short bracket that doesn't come into contact with the A/C plenum.Replaces Ford part number C7ZB-13763-A.Fits:1967...

These courtesy light brackets are located on the very outer right and left under the dash. Typically this bracket is found on the driver side of all 1967-68 Mercury Cougar and Ford Mustang. It is also used on the passenger side if you have air conditioning. This is the short style bracket. There is also a long style for both the passenger side courtesy light if you don't have factory air conditioning. If you have factory air conditioning you would want the short bracket that doesn't come into...

These courtesy light brackets are located on the very outer right and left under the dash. Sold individually, two required per car. Same bracket used on both sides. Replaces Ford part number C9ZZB-13763-A.Fits:1969 Mercury Cougar1969 Ford Mustang

Dash mounting speaker bracket for any 1971-73 Mercury Cougar or Ford Mustang. Typical with single center mounted in-dash speaker with AM radio.Ford part number D1ZA-19A054.

Used bracket for installing the defrost nozzles assembly to the dash on all 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Bracket only, no attaching hardware.

Used bracket for holding either the emergency flasher or turn signal flasher on many Fords dating from 1963. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches to one of two different relay mounting brackets. Couple of different designs were also used. Additionally there is also a different style of flasher mounting bracket. See our related items.Replaces Ford part number C3AB-13351.

Used bracket for holding either the emergency flasher or turn signal flasher. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches directly to the rear of the metal dash with a hex head machine screw.Replaces Ford part number C8AB-13351-A.

Used bracket for mounting the front valance on any 1967-68 Mercury Cougar. L shaped bracket connects the lower valance, stone guard, and inner bumper bracket. Two per car, sold individually.Ford part number C7WB-17A986.

This is used on Mercury Cougars and Ford Mustangs equipped with factory A/C. This is the bracket for the valve that stops the flow of warm coolant when A/C is turned on. This is an exact reproduction and has the zinc dichromate finish.

This bracket clamps the liquid fitting on the liquid hose to the discharge hose on the inside of the radiator support. It's purpose is to keep the lines from moving around during operation.

Used front license plate bracket in Grade A condition. Grade A will only need detailing or a fresh spray of chassis black paint. We include fasteners to attach the license plate to this bracket. This bracket mounts to your front valance. Also available in Grade B condition, see related items below. Replaces Ford part number C7WY-17736-A.

Used front license plate bracket in Grade B condition. Grade B is relatively flat, in most cases it will be slightly bent from prior use. May have cosmetic issues like multiple layers of paint or slight surface rust. We include fasteners to attach the license plate to this bracket. This bracket mounts to your front valance. Also available in Grade A condition, see related items below.Replaces Ford part number C7WY-17736-A.

Used front license plate bracket in Grade B condition. Grade B will, in most cases it will be slightly bent from prior use. May have cosmetic issues like multiple layers of paint or slight surface rust. We include fasteners to attach the license plate to this bracket. This bracket mounts to your front bumper. The 1969 reproduction bracket, which mounts dirrectly to the front valance, is what we recommend for a reasonable priced substitute.Replaces Ford part number D0WY-17A385-A.

Powder Coated. Replaces Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Used lower quarter window bracket for any 1969-70 Mercury Cougar and Ford Mustang non-fastback. This is the lower bracket that mounts to the bottom of the stationary slider bracket. This bracket adjusts the top movement in and out of the rear seat glass. Power or manual crank, hard top or convertible, driver or passenger side. Minor variation on this bracket, some are flat, some have a curve in the vertical edges on both sides. One bracket per window, same for either side. Replaces Ford part...