All Products

Good used core plastic bezel that has had one or more cracks repaired as well as other areas of the plastic where pieces may have been replaced. The process of repair will show on the back side of the piece. There may be some sanding required to prep for a finish. Studs on the back side will be broken or missing. Finish will be very poor or non existent. Keep in mind that we can install a new metal stud on the back to assist in installation at an extra cost.

These will always have some amount of minor pitting. Not for use on XR7 or manual transmission consoles.Casting number as seen on the bottom side C8ZB-65045B72-BW.

Grade "B"s  will show obvious pitting, but will have no cracks. Not for use on XR7 or manual transmission consoles.Casting number as seen on the bottom side C8ZB-65045B72-BW.

NOS lens for the Standard model Cougar optional clock. Not the same as XR7, this clock is would be located in the gauge panel on the driver side instrument cluster. Nice quality, NOS, not polished lenses. Fits 1969-70 Mercury Cougar Standard, body style 65A, 65C, and 76A. Made by Borg Co., which originally made these lenses for Cougars.  *Note - excludes XR7 and Eliminator.

Fits 1968 Standard or XR7

Single black Phillips oval headed screw for attaching the face pads onto 1967 Mercury Standard Cougars (non-XR7 models). Sold individually, we also sell these screws under SKU 100022599 in sets of 13 (better value). *Note - This screw is glossy black in color.

These right and left bezels would be considered grade A cores with no cracks or chips. Often there is a missing mounting stud or two on the backside but nothing that shows. The cluster is complete and all the gauges work. If you would prefer a clock over a dummy plate we can upgrade you at no charge but the clock will not work and often will be missing the tiny knob. If you let us know what mileage you would like the odometer to read let us know and we will try and accommodate. ...

Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent.

Good used core plastic bezel that has had one or more cracks repaired. Finish will be poor or non existent.Ford part number: C7WF-10838

Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent. Check out our video on dash removal and restoration:

Good used core plastic bezel that has had one or more cracks repaired. Finish will be poor or non existent. Ford part number: C8WF-10838 Check out our video on dash removal and restoration:

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing, good chrome on the male buckle and it may even have the date code tag still in place. We will try to obtain the correct date code...

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is a fully functional retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for...

NOS Standard seat belt retractor including bolts and a huge 44" x 33 1/2" Ford seat belt diagram in FoMoCo box and never installed on a car. Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models.  NOTE: Front retractors are same for left and right. Check out our video "All about...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a big block engine. This item requires a $30 core charge.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a small block engine. This item requires a $25 core charge.

Sold individually. Zinc Dichromate (yellow-rainbow)

Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.

Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K

Starter relay that is designed to give a 4 second 'time out' so that your starter can cool down after cranking the engine unsuccessfully to start. 1968 Mercury Cougar and Ford Mustang with R code 428 Cobra Jet engines, including the Shelby GT-500KR. This item will seldom be in stock. There are reproductions available, this one will be Ford OEM original. But we don't have one in stock. Maybe some day.

replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish

These are all new, not rebuilt, concours quality. Features authentic markings and logo. Black case only. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo.  Replaces Ford part # C6AZ-11450-A. *NOTE* There are dozens of styles which were produced by several manufacturers. These parts represent the most common type.

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 16 individual pads in a package.

Now an inexpensive and easy way to convert 1967 - 1970 power steering cars to manual steering. This will give you a more precise feel for the road or track. Eliminates leaking systems and costly repairs. Installs in minutes with no special tools.

This is the most complete kit available for the steering box with 1 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your EARLY short shaft 1967 Cougar or Mustang steering box only with the 1 inch diameter sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a...

This is the most complete kit available for the steering box with 1-1/8 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can...

Reproduction rebuild kit for your 67 Cougar or Mustang steering box. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can rebuild your box with this kit. Early 1967 Steering gear boxes with 1 inch sector shafts. Sector shaft is where the Pitman arms attaches.

Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can rebuild your box with this kit. SMB-K, SMB-D, and SMB-F tagged steering boxes. Probably a DIY youtube video out there for...

This Steering Box Cover Gasket Reproduction fits the 67, 68, 69, and 70. Replaces Ford part #: C3DZ-3581. If your original steering box is one of the few that is still tight then you will want to open it up, clean out all the decades old solidified grease and put new grease in.

Used tilt / tilt away steering column converted into a tilt only unit for the Mercury Cougar or Ford Mustang. All 1967-69 Cougars and Mustangs optioned with a tilt column also had the tilt-away (aka tilt-swing, tilt-fly or tilt-pop). There was never a tilt only option in 1967-69 Cougar or Mustang, no matter what you may have been told... That being said some of our customers prefer not to have the added expense or complexity involved with the swing-away function. This column has been fused at...

Used tilt / tilt away steering column converted into a tilt only unit for the Mercury Cougar or Ford Mustang. All 1967-69 Cougars and Mustangs optioned with a tilt column also had the tilt-away (aka tilt-swing, tilt-fly or tilt-pop). There was never a tilt only option in 1967-69 Cougar or Mustang, no matter what you may have been told... That being said some of our customers prefer not to have the added expense or complexity involved with the swing-away function. This column has been fused at...

Used tilt / tilt away steering column converted into a tilt only unit for the Mercury Cougar or Ford Mustang. All 1967-69 Cougars and Mustangs optioned with a tilt column also had the tilt-away (aka tilt-swing, tilt-fly or tilt-pop). There was never a tilt only option in 1967-69 Cougar or Mustang, no matter what you may have been told... That being said some of our customers prefer not to have the added expense or complexity involved with the swing-away function. This column has been fused at...

Fixed steering column from a 1967 Mercury Cougar. Reasonably rust free column that ships as shown in picture. Often we will leave the turn signal switch in place, but you should count on it being non functional. This steering column will fit a Mustang, but you must change steering boxes. Most 1967 Mustangs came with the steering box with the long spear. Upper and lower mounting brackets, and rag joints are available, but sold separately.

Fixed steering column from a 1968 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often breake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, and wire keeper (wiring cover...

Fixed steering column from a 1969 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, are available, but sold...

Fixed steering column from a 1968 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, are available, but sold...

Fixed steering column from a 1971 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. 1971 and 1972 appear to be the same, but we will ship one from a...

Fixed steering column from a 1972 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. 1971 and 1972 appear to be the same, but we will ship one from a...

Fixed steering column from a 1973 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. 1973 is identified as not having the rubber shrink tubing around the...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is my absolute favorite Cougar - Mustang - Shelby option of all time! In fact, as a rather tall person that is not as slim as I once was, I do not really enjoy driving a Mustang or Cougar that does not have this option. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side...

This is my most favorite Cougar - Mustang - Shelby option of all time! In fact as a rather tall person, that is not as slim as I once was, I do not really enjoy driving a Pony car that does not have this option anymore. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side of the car each time the ignition is turned off and the door is opened. To start the car you must close the door and...

This is a one year only, Cougar only part. I do not care what they told you down at the "Mustang Mega Barn", Cougar is different as it has mounting holes at the top and Mustang does not. The Mustang cover has no mounting holes at the top and resembles the 1970 cover. This may just be the most delicate part found on a 69 Cougar and is just behind good used interior sail panels in scarcity. Rarely do we have this in stock and we can almost assure you we will never be able to come up with the...

This nice used original part will have no broken tabs as seen on our grade 'B' version. This grade 'A' part will include two metal clip-on spacers as shown. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior.

Grade 'A' part that will have none of the four mounting tabs broken or cracked. Enter your preferred color in the order notes at checkout and we will attempt to accommodate you.

This used original part will have a broken tab so you will have to use a over-sized washer or some other clever means of properly attaching it to the underside of your dash. This grade be part will not include the metal spacers seen on our grade 'A' part. Even with a broken tab this is a much better looking and fitting part than our economy reproduction. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. ...

Grade "B" part that will have only one of the four mounting tabs broken or cracked. Select a color and we will attempt to accommodate you.

This is a much better quality part then what you see offered elsewhere. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. Clips temporarily not available from supplier. No clips included at this time.