All Products

Please remove your regulator prior to shipping. Be careful of the mechanical energy stored with the spring under tension.  This is a rebuild service for the rear pancake motor for the Mercury Cougar or Ford Mustang. We completely disassemble these units, then clean and inspect them. Then we will repair or replace minor pieces inside. Please note that if your core is not rebuildable, there will be an extra charge for installing working parts. After the motor is repaired, we...

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

Air conditioning bearing replacement service. Send your wide bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new wide bearing. Price includes new bearing (long or short shaft) and labor, shipping extra.  * Note * There are several pulleys that we are unable to press apart. Please check photos for examples of the known pulleys that we can assemble, but not disassemble. *NOTE* Excludes certain 1968 pulleys with stamped...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...

Our service is to rebuild your sending unit. A quality core is required. This rebuilt XR7 fuel sending unit has been meticulously gone through and made operational again. All sending units are taken apart and media blasted. Once cleaned, the thermistor is carefully removed from the tube and opened up so that the mesh screen and insulator can be chemically cleaned. All wire leads are removed and tested, then resoldered to their contact points. Upon reassembly, initial testing is done with VOM....

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...

Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. Your core must be complete and not overly corroded. We are unable to convert from non-low fuel to low fuel. We also cannot change plugs for different years. We do not repair rust or rust through holes. We do not have critical or specific spare parts for rebuilding....

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Be aware that the OEM Ford 1967 sending units had 5/16 inch tubes for the filter, 1968 had 3/8 inch tubes.Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980...

This option requires that you pay a $65 core charge.  Be aware that the OEM Ford 1968 sending units had 3/8 inch tubes for the filter, 1967 had 5/16 inch tubes. Our service is to rebuild your standard fuel sending unit. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality core must be complete and not overly corroded. We are unable to...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

Basic kit for rebuilding a 1967-70 Holley model 4150 4 barrel carburetor. Includes illustrated instructions. Holley packaged renew kit. This kit is not for model 4160 or other Holley carburetors. See pictures of Holley 4150 below. Click on images to enlarge. ...

Reproduction C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Slightly deeper than the OEM ash trays, plenty of room for installation. Receptacle only, sliding covered retainer sold separately, find it here. Also fits 1965-68 Ford and Mercury full sized convertibles. 

C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Receptacle only, sliding covered retainer sold separately. Also fits 1965-68 Ford and Mercury full sized convertibles. Decades old gum stuck to the bottom is no extra charge...

This receptacle was used on the 1967-68 rear of all consoles except the 1967 standard. It was also used in the rear interior panels of the 1971 - 1973 Cougar for both convertible and coupe. Not correct for 1969 - 1970 convertible rear side panels.Ford part number C5AZ-6230702-A.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Used elbow or connector for the passenger side air conditioning register. This connects the duct tube to the louvered vent. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes with one metal clip as shown for connecting to the register vent.Replaces Ford part numberD1ZZ-19C692-A. The number from the assembly manual is D1ZA-19C677-AA.

Used elbow or connector for the driver side air conditioning register. This connects the duct tube to the louvered vent. Only fits 1971-73 Mercury Cougars.Replaces Ford part number D1WY-19C692-A.

One year only beam that is very prone to rust due to the fact that they were not painted from the factory. Mercury master part number D3WY-17A792-A, also called the front bumper reinforcement beam.

This area of the door often cracks due to the stress caused by worn out hinges. This twelve piece kit includes six screws and six form fitting washers to reinforce the recessed areas that often crack. If your latch area is badly cracked you will want to purchase the repair kit that requires being welded in.

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

Used flexplate reinforcing ring, Ford called it a fly wheel reinforcing plate. Fits all Ford small block engines including 260, 289, 302, 351W and 351C. Strengthens the area where the automatic transmission flex plate mounts to the crankshaft. This is not just a ring with 6 holes in it, it is indexed specifically for the flex plate and only goes on one specific way. It has to be indexed because of the weight on the flex plate. Just under 4 inches in diameter. Special bolts not included, but...

Reproduction flexplate reinforcing ring. Strengthens the area where the automatic transmission flexplate mounts to the crankshaft. 5.12" outside diameter3.34" inside diameter .060 inches thickFits: 352 390 427 428 429 460 with C6 and FMX transmissions.Replaces Ford part # B9AZ-6A6366-B

NOS relay for 1967 Mercury Cougar or Ford Mustang with factory speed control. This is the anti retard relay, identified with the plug with two male connectors. Mounts to the Regulator mounting bracket along with the Brake Release Relay. May also be correct for 1968, we are not sure. Ford part numbers C7WA-9C733-A and C7WY-9C733-A.

Relay for 1969 Mercury Cougar or Ford Mustang with factory speed control. This is the anti retard relay, identified with the plug with two male connectors. Mounts to the Regulator mounting bracket along with the Brake Release Relay.Ford part numbers C9ZA-9C733-B and C9ZZ-9C733-A.

Relay for 1967 Mercury or Ford with speed control. This is the brake release relay. This Relay mounts to the Regulator Bracket.Tested and working relay, this is from a vintage Ford, not sure of the exact application.  Ford part number C7AA-9D737-A.

Relay for 1967 Mercury Cougar or Ford Mustang with Perfect Circle factory speed control. This is the brake release relay. This Relay mounts to the Regulator Bracket. Ford part number C7WA-9D737-A.

Relay for 1968-69 Mercury Cougar or Ford Mustang with factory speed control. This is the brake release relay. Mounts to the Regulator mounting bracket. Ford part numbers C8ZA-9D737-A and C8ZZ-9D737-A.

The function of this relay is to make only the center lights on each side illuminate when you activate the emergency warning flashers. Failure of this relay causes only the center sequential light to flash when using the turn signals. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. This unit is built into the 1967-68 Solid State Sequential Upgrade kit we sell so it is not needed if you are buying the all...

This is known as the "K6" relay in the Ford service manual. The function of this relay is to open the circuit between the two instrument panel turn indicator lamps during normal turn signal operation. During emergency flasher operation, the relay points are closed (normal position) and the two instrument panel indicator lamps flash at the same time. Ford Part # C7WY-10B926-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on...

This is known as the "K6" relay in the Ford service manual, part number C7WB-10C838-C or C7WY-10B926-B. The function of this relay is to open the circuit between the two instrument panel turn indicator lamps on 1967-68 Mercury Cougar during normal turn signal operation. During emergency flasher operation, the relay points are closed (normal position) and the two instrument panel indicator lamps flash at the same time. These relays are tested and working units. UNDER DASH RELAY *NOTE* This...

Referred to as the "K10" relay in the Ford Service manual. The emergency relay, when energized, maintains through circuits from the motor and cam assembly to the rear lamps. During emergency flasher operation, this relay opens the circuits (normal position) to the inner and outer rear signal lamps. Thus, only the center rear lamps operate when the emergency flasher system is functioning. This unit was originally mounted to the underside of the black cardboard trunk filler board on the driver...

Used relay for any 1971-72 Mercury Cougar or Ford Mustang with factory heated back glass or rear defog. Tested and working, with correct plug for connection to electrical harness. Ford part number D1OB-18C641.

Used relay for any 1973 Mercury Cougar or Ford Mustang with factory heated back glass or rear defog. Tested and working, with correct plug for connection to electrical harness.Ford part number D3AB-18C641.

Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1970 Standard model Mercury Cougars (XR7 models use a different relay/bracket) and 1970 Ford Mustang with convenience option. Additionally fits 1970 full size and mid sized Ford and Mercury cars with headlights on reminder option. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D0AB-10C838-A or D0AZ-10C838-A. ...

Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1971-73 Mercury Cougar and Ford Mustang. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D1AB-10C838-A or D1AZ-10C838-A.

Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1970 XR7 model Mercury Cougar (Standard models use a different relay/bracket). This relay controls a buzzer as a reminder to turn off the headlights, or remove the key, when the door is opened.Replaces Ford part number D0WB-10C838-A or D0WY-10C838-A.

Low fuel option electrical relay. Stamped C6AF-10A968-A, Ford engineering number C5AZ-10A968-C. This relay was used on 1965-70 Ford and Mercury full sized cars, 1968-70 Torino/Cyclone/Montego/Fairlane, along with 1967-70 Mercury Cougar and Ford Mustang with that low fuel option. *Note - Generally this will not solve your low fuel indicator problems. The low fuel indicator failure is almost always due to a failed thermistor. The thermistor is located on the fuel sending unit in the fuel tank. ...

Low fuel relay for all 1971-73 Mercury Cougar XR7 models, body code 65F and 76F only. Stamped D1WF-10A968-AA. These are tested and working relays.Fits 1971 Cougar XR7 Fits 1972 Cougar XR7Fits 1973 Cougar XR7

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

This reproduction power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid. This relay can also be used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.Will replace D1AZ-14677-A, AND C1AF-14677-A but will not be an exact fit

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

Used seat back release relay for the 71 - 73 Cougar or Mustang. Located on the relay panel behind the glove box. Ford part number D1ZB-14C690-AA

Used seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1 or Ford Service part number D1AZ-10B924-A

Seatbelt warning light relay for most Ford Lincoln and Mercury cars. This one has a D2AB-10B924-AA part number, but should be the same as the C7AB-10B924-A relay, they are identical except for the part number and the inclusion of "Motorcraft". This is a timed relay that allows several seconds of illumination to your seat belt warning light.These are tested and guaranteed to work.