All Products

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Replaces Ford Part #: C8WA-19F514A

Replaces Ford Part #: C9WA-19F514-A

Replaces Ford Part # D0ZA-A

Reproduction Space Save Tire Instructions Decal for the 1968 - 1973 Mercury Cougar / Ford Mustang

Reproduction Space Saver Spare Recall Postcard for the 1968 - 1971 Mercury Cougar / Ford Mustang

Aluminum spacer used on 289/302/351 engines for mounting the alternator. Length is 1-5/8 inches long, mounts between the alternator and the cylinder head.

Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.

Aluminum spacer for mounting the alternator on 1971 Mercury Cougar and Ford Mustang with 429 Cobra Jet engines. Also fits 1970-71 Cyclone and Torino with 429CJ engines. Spacer measures approximately 1-1/16 inches long. Fits between the cylinder head and alternator housing.

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Used exhaust manifold spacer without butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Straight factory used spacer. Most cars came equipped with a thermal spacer that often times gets frozen with time. No obstruction with this one.Note - Does not fit the slightly larger 428CJ exhaust manifolds. Ford part number C6OZ-9A427.

Fuel tank spacer. Welds to the bottom side of the trunk pan. Spaces the tank, so that the fuel vapor separator assembly, isn't pinched. Easy to make these stands, and there are two needed, are approximately 1-1/2 inches tall. Strap is 1-1/8 inches wide.  

Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. New manufactured.

B8AZ-6359-A Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. Used spacer, will show a little wear from the outside seal. 

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange. Ford part # C9SZ-3C708-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used spacer or retainer, for the 1967-68 Mercury Cougar and Ford Mustang. This filter retainer spacer is made of aluminum and is for the Midland manufactured brake booster. It fits between the master cylinder and brake booster. Nothing beats original FoMoCo!The Ford part number may be C5AZ-2B157-A. 

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Reproduction 384542-S2 Power steering pump adjusting spacer for use without air conditioning. For all 1970 and later Mercury Cougar or Ford Mustang with 302 or 351W engines. Spacer dimensions: 7/16" I.D. and 3/4" thick.*Note - 351C engines use a 1/2 inch spacer.

Replaces Ford Part # C7SZ-3D600-A. Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 9/16" thick.

This unique little adapter was used on XR7G models equipped with a sunroof. This reproduction is bare metal and will not be wrapped in leather like the originals.

This unique little adapter was used on XR7G models equipped with a sunroof. Hand wrapped in the same leather as your center console.

Used exhaust manifold spacer with butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Fully functional, we test these with a heat gun, they do open and close. These thermostat control valve assembly mates to the 1967 and 1968 passenger side 390 exhaust manifold up until about Feb 15, 1968. Easy to tell if it is needed with your manifold, no chamfer for the exhaust donuts at collector? you need this or a...

Reproduction Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang 

Used spacer for the lower windshield moulding, also called an 'anti rattler'. 4 of these plastic pieces were used per car. These spacers were originally installed between the retainers. A total of 7 plastic spacers were used along with 7 metal retainers for that lower windshield moulding. See also C9ZZ-6503150-A (1), and C9ZZ-6503150-C (2).Replaces Ford Part # : C9ZZ-6503150-B, Sold Individually.

Reproduction Lower Windshield Moulding Fender Spacer for the 1969 1970 Mercury Cougar or Ford Mustang 

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

Reproduction engine spacer plate and inspection cover for the 67 - 68 Cougar, Ford, or Mustang equipped with the 289 or 302 V8 with C-4 transmission (code W). 6 bolt bell housing. See related items for inspection cover plate by itself, or bell housing bolts, or inspection cover bolts. Replaces Ford part number C7AZ-7A008-E.

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

Reproduction spacer kit for your 1967 - 1969 Cougar or Mustang Midland power brake booster.

This brake booster to master cylinder spacer was used on many Ford / Lincoln / Mercury products beginning in 1962. Many do not even realize a foam filter is supposed to be sandwiched between the plastic filter cover and die cast aluminum spacer as brake fluid saturates them and the delicate foam filter element deteriorates. The originals were white but after many years become stained. Service replacement units were often black. These spacers were used on Thunderbird Cyclone Torino Fairlane...

Reproduction engine spacer plate for the 1967-68 Mercury Cougar or 1965-68 Ford Mustang equipped with the 289 or 302 V8 with C-4 transmissions (6 bolt only). This is for the 157 tooth flex plate and fits the C4 transmission bell housing. Replaces Ford part number C5ZZ-7007-A or C5OZ-7007-A.

Used engine spacer plate for the 1967-68 Mercury Cougar or 1965-68 Ford Mustang equipped with the 289 or 302 V8 with C-4 transmissions (6 bolt only). This is for the 157 tooth flex plate and fits the C4 transmission bell housing. Replaces Ford part number C5ZZ-7007-A or C5OZ-7007-A.

Reproduction engine block spacer plate for 1969 1970 351 engines FMX (code X) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too.  Replaces Ford part number D0AZ-7007-A.

Factory engine block spacer plate for 1969 1970 351W and 351C engines FMX (code X) and C6 (code U) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions. There are probably two versions of this plate, we believe the the 1969 version did not have the indentations. Replaces Ford part number D0AZ-7007-A.

1967-70 Cougars with any FE engine (390-2V, 390-4V, 427 GT-E, 428CJ, or 428SCJ) and with C6 automatic transmission or manual transmissions.  Ford part #: C3AZ-7007-D.

Early version of the FE engine / Transmission spacer plate. Has 1 medium sized hole instead of 3 smaller holes above the crankshaft. Originally was for either automatic or manual. Ford part #: C3AZ-7007-A.

1971 429CJ Block spacer plate for use with automatic (code U) transmissions.

Reproduction engine spacer plate for the 67 - 68 Cougar or Mustang equipped with the 289 V8 with manual transmissions (6 bolt only).Replaces Ford part number C5DZ-7007-A.

1967 1968 Cougar with 289 engines and a 3 or 4 speed manual transmissions. Will only work with 157 tooth bellhousings and flywheels. Replaces Ford part number C5DZ-7007-A.

Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.