Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 
Filter Products by


Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 2737-2784 of 13397
$0 Price: $35.85

Buy Details

Availability: Rare / NOS Part
Item #: 32881 -

NOS distributor lead wire with green boot for the coil. Direct replacement for 1968-73 Ford distributors. There were several colors of boots that go to the coil, this is a green one as shown. Ford part number C7VY-12216-A.

$0 Price: $25.45

Buy Details

Availability: Discontinued, Limited Stock on Hand
Item #: 41402 -

Reproduction distributor lead wire without the boot for the coil. There were at least two different lengths of wire leads found on 1967 Mercury Cougar and most all other Ford and Mercury distributors. This is the longer wiring harness, about 20 inches outside of the distributor. Direct replacement for 1961-67 Ford distributors.

$0 Price: $10.35

Buy Details

Availability: In-Stock Item
Item #: 41353 -

C8AF-12A022-A For all 1967 - 71 V-8 distributors. Concours correct head stamping. Brass plug for the stock Autolite distributors. Installs as shown.

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31599 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with dual nipple connections. 

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31600 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with single nipple connections. 

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31602 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31601 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31598 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31597 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31603 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1971 Mercury Cougar or Ford Mustang with 429CJ engines. Distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31604 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1971 Mercury Cougar or Ford Mustang with 429CJ engines. Distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

$0 Price: $34.55

Buy Details

Availability: In-Stock Item
Item #: 31596 -

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. 1969-70 Mercury Cougar Eliminator with Boss 302 and 1969-70 Ford Mustang with Boss 302 engines.

MSRP:$64.99
$64.99 Price: $55.69

Buy Details

Availability: In-Stock Item
Item #: 14-0005 -

New rear seat to trunk steel divider for your Mercury Cougar. We had this one made specifically for the Mercury Cougar and it is designed to replace the flimsy tar based cardboard factory divider.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken. When installed properly behind the rear seat, this 18 gauge steel divider will provide stiffness to the chassis. This divider can be bonded, screwed or welded into your car...

MSRP:$64.99
$64.99 Price: $55.67

Buy Details

Availability: In-Stock Item
Item #: 14-0004 -

NOTE: You  can save on shipping costs by ordering our template (traced out on butcher paper) and cut your own. New rear seat to trunk steel divider for your Mercury Cougar. We had this one made specifically for the Mercury Cougar and it is designed to replace the flimsy tar based cardboard factory divider.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken at the top or bottom. When installed properly...

MSRP:$64.99
$64.99 Price: $9.85

Buy Details

Availability: In-Stock Item
Item #: 33749 -

This listing is for a template of the rear seat to trunk steel divider for your Mercury Cougar. Beneficial for international customers who would like to save on shipping costs, or anyone who can use this template to cut their own from the sheet metal of their choosing. Traced out on butcher paper.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken at the top or bottom. When installed properly behind the rear...

$0 Price: $45.86

Buy Details

Availability: In-Stock Item
Item #: 12134 -

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

MSRP:$12.00
$12.00 Price: $10.55

Buy Details

Availability: In-Stock Item
Item #: 32069 -

Made from clear acrylic plastic with prisms added to increase the bulb brightness.Ford originally used white nylon with no prisms, which makes the light very dull. Replaces Ford Part # D1AZ-13783-B.

MSRP:$12.00
$12.00 Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 13916 -

Great fit. There were two different mounting tab styles used in the 1970's, this one is 100% correct for the 1971 Standard Hardtop Cougar manufactured before 6/71 and fits the early 1971 housing we sell. Ford Part # C6OZ-13783

MSRP:$12.00
$12.00 Price: $5.95

Buy Details

Availability: In-Stock Item
Item #: 14309 -

This was used on many Ford products but this bezel is 100% correct for the 1971 - 1973 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971 - 1973 Cougars or Mustangs if you purchase the matching Bezel. No Cougar had a dome light in 1967-70. Ford Part # D1AZ-13783-B.

MSRP:$20.00
$20.00 Price: $12.75

Buy Details

Availability: In-Stock Item
Item #: 13936 -

Nice chrome finish. This was used on many Ford products but this bezel is 100% correct for the 1971 Standard Hardtop Cougar manufactured before 6/71. No Cougar had a dome light in 1967-70. Ford Part # D0AZ-13788-A.

$26.00 Price: $36.45

Buy Details

Availability: In-Stock Item
Item #: 14341 -

Nice chrome finish with Bulb. This was used on many Ford products but this bezel is 100% correct for the 1971-73 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971-73 Cougars or Mustangs if you purchase the matching dome lens. No Cougar had a dome light in 1967-70. Ford Part # D6UZ-13788-A.

$0 Price: $9.35

Buy Details

Availability: In-Stock Item
Item #: 11948 -

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 429CJ or Super Cobra Jet engines Mercury Cougar, Ford Mustang, and 1970-71 Torino/Cyclone.Fits between exhaust manifold and header pipe (H pipe) 2-13/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H pipes. Replaces Ford part number C8SZ-9450-A.

$0 Price: $4.80

Buy Details

Availability: In-Stock Item
Item #: 16238 -

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

$0 Price: $6.60

Buy Details

Availability: In-Stock Item
Item #: 12341 -

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

$0 Price: $23.85

Buy Details

Availability: In-Stock Item
Item #: 41711 -

Concours correct engine pipe donut, metal, factory original dual sized design to properly seal H-pipe to Exhaust manifolds MCA approved, sold individually.Replaces Ford Part # C8LV-9450-AFits between exhaust manifold and header pipe (H or Y pipe) 2 1/16 id 3 5/8 od cast iron, tapered top and bottom, smooth inside.Note! These are very difficult to seat compared to the pliable ones we sell. If you do decide to use the steel version it is recommended you apply a liberal coating of Permatex High...

$0 Price: $18.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0338 -

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

$0 Price: $16.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0326 -

Air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1969-73 door, but without a small notch. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

$0 Price: $16.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0325 -

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

$0 Price: $16.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0329 -

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

$0 Price: $4.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33788 -

Warning lens indicating "DOOR" and "BRAKES", attaches to the Oil / Temp gauge bezel on any 1970 Mercury Cougar XR7. These are red back lit warnings to let you know that your door is not closed or the brake system is suspect. 1970 lens has white lettering and is visible when the warning light is not lit. Ford part number D0WY-10A936, casting number D0WF-10A936.

$0 Price: $124.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 17295 -

Used door / lid for the glove box in the Mercury Cougar, grade "A". This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time. Standard model Cougar, not for XR7.Plan on painting to match your interior. Ford part # D1WY-6506024-A for the inner,...

$0 Price: $46.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 54545 -

Used door / lid for the glove box in the Mercury Cougar, grade "B". This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time.Plan on painting to match your interior. Ford part # D1WY-6506024-A for the inner, D1WY-6506024-B for the outer. ...

$0 Price: $55.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12110 -

Used door / lid for the glove box in the 1967 Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. We have found this door on 1967 and into 1968 Cougars. Sometime in early 1968 this glove box door came with three holes on the back. Both glove box doors fully interchange. Bead blasted for the photo, door ships without rust, in most cases you will want to paint prior to installation.Ford part # C7ZZ-6506024-A.*NOTE*...

$0 Price: $55.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 16183 -

Used door / lid for the glove box on any 1968 Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. We have found this design of door with the 3 holes, well into the 1968 production run. 1967 and early 1968 doors are typically without the three holes on the back. Both glove box doors fully interchange. Bead blasted for the photo, door ships without rust, in most cases you will want to paint prior to installation.Ford...

$0 Price: $49.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12111 -

Used door / lid for the glove box in the Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. Dent free, may have minor surface rust. Ford part # C9ZZ-6506024-A.

$0 Price: $48.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 16798 -

Used door / lid for the glove box in the Mercury Cougar, grade "B", with at least one crack, or an extra chip or scrape. This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time.Plan on painting to match your interior. Ford part # D1WY-6506024-A...

$0 Price: $4.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33787 -

Warning lens indicating "DOOR AJAR" and "BRAKES", attaches to the Oil / Temp gauge bezel on any 1969 Mercury Cougar XR7. These are red back lit warnings to let you know that your door is not closed or the brake system is suspect. Ford part number C9WY-10A936, casting number C9WF-10A936.

$0 Price: $119.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31016 -

Passenger side power window door and main harness from a 1969 Mercury Cougar and 1970 built before 2/2/1970. Tested and inspected and ready to install. Does not fit late 1970 cars.  Ford part number C9WB-14630 Product Condition Grades Below is a general description of what the criteria is for our product condition grades. These are generalizations that are intended to give you an idea of the condition of the product at a quick glance. Because different parts degrade at different...

$0 Price: $50.54

Buy Details

Availability: In-Stock Item
Item #: 32946 -

This listing is for the outer doors pieces only, Cougar and Mustang are identical. Sold only as a pair.Replaces Ford part numbers C7ZZ-6521453-A  and  C7ZZ-6521452-A

$0 Price: $124.85

Buy Details

Availability: Rare / NOS Part
Item #: 33312 -

This was originally a 6 piece set for both the Convertible and Coupe. It could be ordered as a stand alone or part of the protection package which included door edge guards, bumper guards and floor mats. The door strip is the longest and can be cut to fit the fenders or quarter panels.

$0 Price: $19.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31572 -

Used door courtesy light lens on the 67 - 70 Cougar. Because of the heat and placement of the bulb behind this lens, they were prone to burning or in some cases melting. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the reflector lens here. Right is same as left, sold individually. ...

$0 Price: $9.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31571 -

Used door courtesy light reflector used on 67 - 70 Cougars. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the light lens here. Right is same as left, sold individually.

$0 Price: $55.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24201 -

Used driver side (left hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

$0 Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24204 -

Used passenger side (right hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

$0 Price: $189.85

Buy Details

Availability: Out of Stock
Item #: 32700 -

NOS, new old stock, Stainless steel clip on guards for the rear edge of the 1969 and 1970 Cougar doors. Would have been part of the exterior decore option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number C9WY-6520910-A.