All Products

These are our 2-inch diameter round decals to customize the plastic Legendary Wheel Co. center caps that come with their wheels. These caps are also available separately, see item # 30529. Nice quality vinyl that will last outdoors, and the graphics have a mirror finish to compliment the chrome. *If you're buying a set of Legendary Wheels from us, mention this item in the notes and we'll include them for free! ...

New "Mercury" script decal in black for any Mercury, but will be at home on the Cougar. Measures 10 3/4" wide by 1 1/2" tall.This is a die-cut vinyl decal. To install, you'll have to peel off the backing, apply the decal to the intended clean surface, press in place with a plastic squeegee or credit card, then carefully peel away the top contact paper.

Reproduction oil cap decal for the 67 - 70 Cougar or Mustang. 

This decal was used on the Standard model Mercury Cougar for 1968 and both the XR7 and Standard model Mercury Cougar for 1967. Will require slight trimming for perfect fit. If you place a piece of 80 grit sand paper (or file/emery board) on a firm surface you will be able to bring the height of the decal down with just a few strokes of both the upper and lower edge. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive...

Located on the bottom side of trunk lid.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these. Sold as a Pair. Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

Located on either the left or right hand shock tower. On rare occasion we also have seen these above the washer bottle on the 69-70 models. Replaces Ford Part #: C7AE-6C029-A.

Located on either the left or right hand shock tower. On rare occasion we also have seen these above the washer bottle on the 69-70 models.

Reproduction Sun Visor Decal Starting Instructions for the 1967 - 1968 Mercury Cougar / Ford Mustang 

Here's a good replacement for those old worn out aluminum "stereo" decal inserts for your 69 - 70 door speaker grills. Keep in mind that these are just simple decal stickers and are not made from aluminum as the originals were. We do offer used aluminum decals here.SOLD INDIVIDUALLY. ...

Reproduction Tire Pressure Decal for the 1968 Mercury cougar

Tire pressure / tire size / maximum load decal for the 1969 Mercury Cougar equipped with the 302, 351, 390 or 428 engine. Printed with Ford Part # C9WA-1532-B.

Reproduction Tire Pressure Decal for the 1970 Mercury Cougar

Very correct looking reproduction used only on the 1968 XR7 Mercury Cougar. This decal may need slight trimming to fit perfectly into the recessed portion of your lock cover.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made.

Reproduction of the firewall vacuum tree decal that is affixed to six port plastic vacuum tree that is located in the middle of the firewall, just below the horizontal body seam.Ford Part # D0OZ-9C490-C

Used until early 1970 when vehicle was equipt with AC. Decal Text: Autolite Regulator C8TF-10316-A NEG

This walking cat decal measures 10.5" x 3.65".

This walking cat decal measures 10.5" x 3.65". Check out the very first Cougar in our video below!

This walking cat decal measures 10.5" x 3.65".

This walking cat decal measures 10.5" x 3.65". Check out the very first Cougar in our video below!

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Pictured below is Robin Miller's "G-Force" Cat! Click on images to enlarge. Check out this video of our 2013 Open House event! ...

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Check out the very first Cougar in our video below!

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog.Check out this video of our 2013 Open House event. See you next year! ...

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog.Check out this video of our 2013 Open House event. See you next year! ...

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog. Shown in Black.

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog. Shown in Black.Check out our video f the 2013 Open House event. See you next year! ...

These decals are really impressive quality. They stick on really nicely, have super grip and a nice glossy finish. You can use them to make up your own signs, decorate your shop wall, trailer, or make up that car show easel/sign that you have been needing. Available only in left facing (traditional pose). Check out this video of our 2013 Open House event. See you next year! ...

Rare, almost impossible to come by collectors item designed to adhere to the inside of your window. Original water transfer 3" diameter Cougar logo decal. Soak in water for 30 seconds and slide onto glass. I have only seen these dealer "give aways" one other time in all my years of collecting. We want to you to keep in mind that the cloudy areas you see on the decal in the picture are nothing more than paper residue, and will easily wipe off. Check out the very first Cougar in our video below! ...

Nicely done reproduction with the only difference being that it adheres to the outside of the window and the originals adhere to the inside. Check out the very first Cougar in our video below! ...

Reproduction Dan Gurney Special window decal in black and gold for the Mercury Cougar. Check out the very first Cougar

Tips for installation: Decal should be trimmed to resemble the original decal. This one is comes as a full rectangle and the original was trimmed around the edges w/ very little clear border left.This decal is a very "touchy" decal, any air bubbles WILL leave the adhesive white where the bubble was even if you get it smoothed/pushed out so you must put the decal down avoiding ANY air bubbles by laying one edge first and rubbing as you go along. If you just lay the decal down you WILL end up w...

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

Reproduction Decal Set / Under Hood Paint OK for the 1969 - 1971 Mercury Cougar or 1971 Ford Mustang 

Here are our reproduction black 428 CJ fender decals for your Mercury Cougar. These are the same size and font of the originals and would look killer on any Ford equipped with the 428 engine. We were able to get our hands on a NOS decal to use for reference, so these are spot-on. See pictures for placement on the fender. Each decal measures 5 9/16" x 7/8".Replaces Ford part # C9WY-16228-B.

Here are our reproduction white 428 CJ fender decals for your Mercury Cougar. These are the same size and font of the originals and would look killer on any Ford equipped with the 428 engine. We were able to get our hands on a NOS decal to use for reference, so these are spot-on. See pictures for placement on the fender. Each decal measures 5 9/16" x 7/8".Replaces Ford part # C9WY-16228-B.

Used on both the speedometer and temperature / fuel gauge. Comes with plastic keeper washer that connects it from the backside of the lens. Sold individually, two required per cluster. These are in used condition as shown and need restoration.

New Old Stock 'DEFOG' knob. Attaches to hand down defog switch on 1969-70 Mercury Cougar and Ford Mustang with rear defogger option. *Note - Excludes 1970 Mercury Cougar XR7. Those cars had the defog switch in the courtesy light panel. Replaces Ford part number C9WY-18519-A.

Used switch for the rear defog or defogger fan on any 1970 Mercury Cougar XR7. Rocker switch only. Tested and working two speed switch. Replaces Ford part number D0WY-18578-A.*Note - 1970 Standard Model Cougar uses the 1969 Mercury Cougar switch over the radio.

Used service replacement switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and chrome knob, bezel is marked "DEFOG" as shown. *Note - this is not the OEM 1968 defog switch, it is the switch used in defog kits starting in 1970 for many Ford and Mercury dealer installed or over the counter kits.Replaces Ford...

Used switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and black knob marked "DEFOG". Replaces Ford part number C8ZZ-18578-A.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a grade "A" unit with no issues other than some discoloration.Ford part # D1ZZ-18490-B.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield.Ford part # D1ZZ-18490-B.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang without A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield. You will need to staple the flex part onto your heater unit. Very fragile part, almost always going to have Grade B, seldom will we have a Grade A used.Ford part # D1ZA-18A565-AD

This plastic panel affixes to the radio bezel from the backside. Very rare item... For example, according to Kevin Marti, in 1971 only 1451 Cougars came equipped with this panel. The reason a car would be ordered radio delete from the factory was often the dealer knew he would have his sales people upgrade the customer to a stereo or 8 track. Sometimes people would special order their cars radio delete as they knew they would be taking a trip to the local stereo store within the first week....

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing, good chrome on the male buckle and it may even have the date code tag still in place. We will try to obtain the correct date code if...

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is a fully functional retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for...

Grade A used deluxe shifter handle in black. Nice used condition, minor cracks in the plastic on the bottom. No release button or set screw included. Fits 1967 Mercury Cougar XR7 and 1967 Ford Mustang with IDG or Interior Decor Group and all Shelby Mustangs with automatic. This one year only, T handle, has concave or recessed buttons.  Ford part number C7ZZ-7213-A. We know that Scott Drake is using this number for 4 speed manual knobs, which was a made up Ford part...

Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...