All Products

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

NOS Air conditioning belt tension pulley for Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968.  Ford part # C7AZ-8678-B. NOTE* Send in your old core for a credit toward the purchase of this NOS pulley. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. Check out this video

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Air conditioning belt tensioning pulley for Ford Galaxie and other full sized Ford and Mercury cars with the 289. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click here to view the repair bearing (ITEM #: 11-0413), we've got what you need! Ford part # C5AA-8A619-F or C5AZ-8678-F ...

Air conditioning belt tensioning pulley for Ford Thunderbird and other full sized 1968 and 1969 Ford, Lincoln, and Mercury cars with the 429. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click here to view the repair bearing (ITEM #: 11-0413), we've got what you need! Ford part # C8VA-8A619-B ...

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. Check out this video

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 428CJ engine. This is also a service replacement part for the C8AZ-8678-B fixed idler pulley. The only difference between them is that this part has the larger bearing.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which...

Good used actuating rod for the ignition switch on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang. 8-1/8 inches on rod center long.

This is the electrical portion of the new for 1970, locking column mounted switch. This is the rod actuated device mounted on the top of your column under the plastic collar cover. See page 33-02-06 of your 1970 shop manual for proper installation and adjustment. Working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. These are tested and repaired as necessary by our Electrical Dept. Ford part number D0AZ-11572-A. While there's...

New old stock NOS Motorcraft stamped ignition switch for any 1967 Mercury Cougar or Ford Mustang. Technically this is a later service replacement switch, still made by Ford. Ford number C5AZ-11572-B.Here is a helpful "How To" youtube video on how to replace your ignition switch.

NOS ignition switch kit for any 1968-69 Mercury Cougar or Ford Mustang. Includes ignition cylinder and plug with pigtail wires. This is a new old stock Motorcraft part. Comes as shown, you will need to reuse your key lock cylinder. Ford part number D1AZ-11572-C.

Used under dash wiring harness repair plug and pigtail to the ignition switch for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use.

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use after nearly 40 years.

Used inner and outer driver side (left hand) wheel house as cut from a 1971-73 Mercury Cougar parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion. Used inner and outer driver side...

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

1970 Mercury Cougar standard and Eliminator rimblow horn pad bezel with hand painted woodgrain. These have been painstakingly hand painted by a local artist. 1971-74 standard and 1971-74 XR7 straight style woodgrain. Cores cannot be bent or rusted heavily. Does not include the 'kitty', Cougar Emblem sold separately. Core charge is refundable when restorable 1970 woodgrain insert is received by WCCC. Check out this video ...

1970 Mercury Cougar XR7 rimblow horn pad bezel with hand painted burl woodgrain. These have been painstakingly hand painted by a local artist. 1970 XR7 burl woodgrain.  Does not include the 'kitty', Cougar Emblem sold separately. Cores cannot be bent or rusted heavily. Core charge is refundable when restorable 1970 burl insert is received by WCCC.Check out this video ...

Driver quality used left side or driver side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

Grade A used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This is a real clean rust free cover but if you are wanting to save money, we have grade B's which will have a dent or creases for about half the price. Find the grade B here.Ford part number C3AZ-6366-A. ...

D0ZZ-5493-A Rear sway bar bushing with 1/2" diameter opening. Used on rear anti-sway bar on the 1970 Eliminator and 70 - 73 models ordered with the competition handling package. Casting number as seen on the bushing is D0ZA-5484-E. Sold individually.

Ford part number 3E629. Molded rubber construction, fixed and tilt steering columns. These may have been used as early as late 1972, not sure. Limited stock. The reproduction plastic version for 1969-72 will also fit and work in conjunction with the available foam insulation. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

C4DZ-5415-A Sold as a pair

C5OE-9425-A Cast iron intake manifold used on all 1965 A code 289-4V engines in a Ford or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C5OE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. We did a quick clean up with the bead blaster, this one should clean up very nice. This is the actual intake in the photos, water neck included. Early 1965 date code. 4G2 or August 2, 1964...

Very rare, early version, over the counter, Group II dress up accessory item for any 289 / 302 small block engine. This over the counter Intake was marketed by Shelby American in the Cougar catalog titled "How To Sharpen Your Cat's Claws". Shelby casting number S2MS-9424-A. The early version differs from the late in that it is missing the three bosses on the passenger side that are seen on the later versions. This intake is identical to the last COBRA intakes that came on the late build...

Cast iron intake manifold used on all 1972 Q code 351-4V or 351CJ engines in a Mercury Cougar or 1971-72 Ford Mustang. Stock 4 barrel spread bore intake manifold. Take off manifold with correct casting number of D1ZE-9425-BB . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1ZE-9425-BB. *Note - 351 Cleveland engines only.

C8TE-9425-A Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used after 1-9-1968. Take off manifold with correct casting number of C8TE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-R. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

C7TE-9425-G Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used before 1-9-1968. Take off manifold with correct casting number of C7TE-9425-G. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-P. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

C7AE-9425-J Cast iron intake manifold used on 1967 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold, used after 9-11-1967. Take off manifold with correct casting number of C7AE-9425-J. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-N. *Trivia - One of the heaviest car intake manifolds ever made, over 80 lbs.

C9ZE-9425-A or -B Cast iron intake manifold used on all S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-A or -B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-A. Current date 8H14.*Installation Tip - A water heated aluminum spacer plate with PCV provision is needed for proper air cleaner clearance....

Lightly used intake manifold cast aluminum 427-4V medium riser. Blue Thunder casting 427MR-4V. Has the oil fill tube in front, dual plane, and the road draft provision in the back. Very tall manifold, likely to not fit under the stock hood of a Cougar or Mustang. Do your research on this, if you know, you know. We don't. Small portion on the driver side front has been lightly ground down, likely for a coil. No other issues noted. 

D0OE-9425-D Cast iron intake manifold used on all 1971 C or J code 429CJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0OE-9425-D. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. This unique manifold used a General Motors Rochester Quadrajet carburetor with a spread-bore pattern. Typical after-market carburetors like Holley will not work on this intake...

D0OE-9425-C Cast iron intake manifold used on 1970 and 1971 C or J code 429 Super Cobra Jet engines in a Mercury Cyclone or Ford Mustang or Torino. Stock square bore 4 barrel intake manifold. Square bore is four equal venturi holes normally for Holley carburetor applications. Take off manifold with correct casting number of D0OE-9425-C. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Not sure of the casting date.This cast...

C9ZE-9425-D or C9ZE-9425-E Cast aluminum intake manifold used on all 1969 G code Boss 302 engines in a Mercury Cougar Eliminator or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-D or -E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-C. Has "Buddy Bar" cast into the bottom side.

D0ZE-9425-E Cast aluminum intake manifold used on all 1970 G code Boss 302 engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0ZE-9425-E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-D or -E.

C7AE-9425-F Cast aluminum intake manifold used on all 1968 W code 427-4V engines in a Mercury Cougar GT-E or 1968 Ford Mustang Shelby GT-500 (non KR models). Stock 4 barrel intake manifold. Take off manifold with correct casting number of C7AE-9425-F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-H. *TRIVIA* This is also known as the PI aluminum intake manifold, PI = Police Interceptor. ...

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

Used FoMoCo aluminum intake manifold for Ford FE engines. The single plane carburetor mounting bases, indicate that this was designed for Ford Thunderbird with 390 engines. Stepped bases were for Ford Galaxie. FoMoCo marked, with a 1D20 casting date i.e. April 20, 1961. There has been some repair done to the area of the water neck, and at least one of the threaded holes is buggered up. No linkage, carburetors, nor fuel logs included. Fits all Ford FE engines 360, 390, 406, 427, 428. ...

AS OF NOW, NONE OF OUR SUPPLIERS ARE MAKING LEATHER UPHOLSTERY. THIS ITEM IS NO LONGER AVAILABLE FROM WCCC. Unfortunately all of the manufacturers of the Leather Upholstery Kits have stopped producing them. Most customers are happy with the Vinyl kits that we offer.

Upholstery components have an ETA of 10 - 12 weeks.Complete reproduction comfortweave vinyl interior upholstery kit in medium green for the Mercury Cougar convertible. This is the complete vinyl interior upholstery kit which includes the vinyl upholstery for the front and rear seats. The front seat set will fit both the coupe and convertible, but the rear seat is a different animal and will fit the convertible only.*NOTE* This comfortweave kit would not be considered concours correct because...

A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.               ...

Upholstery components have an ETA of 10 - 12 weeks. A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.*NOTE* This product will take 6 - 8 weeks for delivery.               ...

Upholstery components have an ETA of 10 - 12 weeks.These interior kits feature the correct horizontal basket weave pattern on the uppers, correct stitching, correct grain and color of quality vinyl and correctly embossed clip on seat backing boards. Unless you specify otherwise, we do not drop ship these from the manufacturer but rather have them sent to us first so that we can closely inspect the quality of workmanship and check for accuracy in the materials. We try to the more common colors...

Upholstery components have an ETA of 10 - 12 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials. Click on images to enlarge. ...

Door Tag Trim Code: 6A. Black XR7 Vinyl Upholstery kit to cover the rear seat for the convertible.

Upholstery components have an ETA of 10 - 12 weeks.Nugget Gold XR7 Convertible Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 -...