All Available Parts - 1971 Mercury Cougar

Used grade A near perfect dog dish style hubcap / Wheel Cover for the 1970 Mercury Cougar Eliminator. This same cap was standard equipment for the 1971-73 Mercury Cougar and was used with dealer installed trim rings when the optional 15x7" wheels were ordered on 1971-72 Cougars. There were two versions for this cap, one had a brushed finish where the other had a bright finish. These are all driver quality with some dings and or scratches. The one pictured is brushed, but we often have both in...

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

Used grade B less than perfect with a couple dings / scratches / blems dog dish style hubcap / Wheel Cover for the 1970 Mercury Cougar Eliminator. This same cap was standard equipment for the 1971-73 Mercury Cougar and was used with dealer installed trim rings when the optional 15x7" wheels were ordered on 1971-72 Cougars. There were two versions for this cap, one had a brushed finish where the other had a bright finish. These are all driver quality with some dings and or scratches. The one...

Wiring harness under hood segment from circuit breaker through the firewall to the convertible power top switch on any 1971-73 Mercury Cougar or Ford Mustang.  Part number D1ZB-15A669-A.

Clean cores are required for this service, cores that are turned in for this service that are kinked, heavily pitted or mouldings with several holes drilled into them are not worth restoring. That being said, often all of the gravel pitting usually found at the front cannot completely be removed as it would result in a product that will be too thin.

Aluminum cover for the sunroof cable housing on any 1967-73 Mercury Cougar and many other vehicles that used the Golde sun roofs. Golde was a company from West Germany and also supplied parts to many other auto manufacturers such as Mercedes-Benz, Porsche, VW, BMW, Mopar, and Ford. ASC was the company that installed sun roofs for Ford US, and they used Golde components. Casting number Golde 100 413 605.

Aluminum housing for the sunroof cable drive, connects to the motor on any 1967-73 Mercury Cougar and many other vehicles that used the Golde sun roofs. Golde was a company from West Germany and also supplied parts to many other auto manufacturers such as Mercedes-Benz, Porsche, VW, BMW, Mopar, and Ford. ASC was the company that installed sun roofs for Ford US, and they used Golde components. Casting number Golde 100 413 600 / Golde 100-413-600 / Golde 100413600. ...

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

Used seat back release relay for the 71 - 73 Cougar or Mustang. Located on the relay panel behind the glove box. Ford part number D1ZB-14C690-AA

Concours rear axle vent for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Metal nipple that screws into the top of the rear axle housing. AMK reproduction, 7/16-20 threads, 9/16 wrench size. Ford number is C5ZZ-4022-B, but AMK and others list the fictional part number of C8ZW-4338-A. Ford chassis assembly manuals, indicate that this is part number 4022.

Reproduction bolts and washers for the manual transmission bell housing on any 1969 - 73 Cougar or Mustang equipped with a 302 / 351 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1969-73.

Reproduction bolts and washers for the automatic transmission bell housing on any 1971 - 73 Cougar or Mustang equipped with a 351 engines and C-6 transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1971-73.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "B" part and will have one defect. This part will have a crack, chip missing, etc. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

Used distributor modulator upper speedometer cable for 1971 - 1973 Mercury Cougar and Ford Mustang with the FMX or automatic transmission. Cable that connects the back of the speedometer and the speed sensor of the modulation system. Shown to be 10.54 inches long. 

This is the 2020 edition of our famous Classic Cougar Calendar! Once again, we recruited photos from the community, and sprinkled in some of our own as well. We think the end result is a great variety of cars and locations. Big thanks to everyone who submitted photos! Another dozen of the entries are featured on an "Honorable Mentions" page. Each month page includes multiple photos, in addition to extra written info about every car. As an added bonus, scattered within are some fun little...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

Rare find, NOS rubber rub strip for the front bumper guard on 1971-72 Mercury Cougar. These hard rubber bump strips attach to the front bumper guards with 2 studs from the back side. Sold individually, right is the same as left, Ford Casting number as found on the back is D1WB-17A812-AB

New Cougar poster by WCCC! Featuring a 1969 XR7 Convertible against a stunning sunset and impressive skyline, this 20" x 30" poster is printed on heavyweight archival paper and features a semi-gloss finish. Suitable for framing, this print would make a great decoration in your garage or living room.  *NOTE - Please excuse the typo on our phone number at the bottom of the poster! The phone number on our business cards and at the bottom of our website is correct. ...

Reproduction 1/2" hose clamp, commonly used on the fuel lines. This clamp is smaller than the ones used on the power steering return line.

Used vacuum actuator for controlling the center A/C vent on any 1971-73 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Ford part number D1ZZ-18A318-A.

New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.

Detachable mounting plate for installing the convertible ram cylinder to the convertible top frame assembly behind the quarter interior panel. Right and left are the same, fits all 1971-73 Mercury Cougar and Ford Mustang convertibles. Ford part number D1ZZ-76531A19-A.

Good original used toggle tip for the 1971 - 1973 Mercury Cougar XR7

This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...

Ford called this part the fuel vapor separator. It mounts to the top of the fuel tank. This is part of the emissions control smog system, the fuel vapors that are collected in the charcoal canister are returned through a hose to this device into the fuel tank. Applications for this part include: 1971-73 Mercury Cougar and Ford Mustang, 1971-72 Pinto and Bobcat, 1971-72 Maverick and Comet, 1971 Thunderbird and Lincoln MKIII, and 1971-73 Ford / Mercury full sized cars. Starting about 1973, this...

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Reproduction premium quality disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. These are considered concours correct and show quality.  Check out the link below for some information on master cylinder caps: http://anghelrestorations.com/uploads/3/5/1/2/35122002/master_cylinder_caps_1.5.pdf   Replaces Ford part # C7AZ-2162-B. Fits: 1969 Mercury Cougar1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang / Torino1970...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No cracks or chips, every unit is thoroughly tested. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13441-AA ...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No cracks or chips, every unit is thoroughly tested. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13440-AA ...

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

NOS Ford replacement driver side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-B

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Used power steering oil cooler for many 1971-73 Ford, Lincoln and Mercury cars with air conditioning. Specifically these came from 1971-73 Mercury Cougar or Ford Mustangs with factory installed air conditioning and power steering. This unit mounts to the top of the A/C compressor. This installs inline with the low pressure return hose.  Manufactured by the Blissfield Company and has a Ford stamped number of D1AA-3D746-AB. The Ford engineering number is D1AZ-3D746-D. 

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

OUR SUPPLIER IS CURRENTLY OUT OF THIS ITEM. ONCE THEY BEGIN PRODUCTION AGAIN, WE WILL UPDATE OUR SITE. ETA  4-6 MONTHS. This Group 24 Autolite Sta-Ful battery is NOT a generic battery inside a case, but rather an authentic reproduction of the originals that use the original case, and not just cover molds. These batteries are maintenance free, utilizing the latest Absorbent Glass Mat technology, so they never require adding acid or water. The electrolyte is trapped in the separators so the...

These new navy blue shirts feature a distressed white graphic with the slogan, "It's Like A Mustang, Only Better!" and "Cougar: Since 1967", wrapped around the image of a first-generation Cougar. This design is a WCCC original, and we think it sums up most Cougar owners' true feelings about their cars. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

New clear passenger side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces Tempered clear glass.

New clear driver side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces Tempered clear glass.

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness. Kit includes: (2) High Beam Bulbs / Housings (2) Low Beam Bulbs / Housings (2)...

Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness. Kit includes: (2) High Beam Bulbs / Housings (2) Low Beam Bulbs / Housings (2)...

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Replaces Ford Part #: C8OZ-13713-A.

Crankshaft oil slinger for all 351C or Cleveland engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number D0AZ-6310-A.

Crankshaft oil slinger for all 429, 429CJ, 429SCJ, Boss 429, or 460 engines, the "385" series. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number C8SZ-6310-A.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

When ordering this item, you do not need to order a key blank, the key is included.This listing is for the ECONOMY version of the trunk / glove box key.We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the factory. These are not copies, they are new keys! What we need to do this properly, is the number...

When ordering this item, you do not need to order a key blank, the key is included.This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the factory. These are not copies, they are new keys! What we need to do this properly, is the number...

This rechromed lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several...

Reproduction overflow hose with smooth outer wall. Hose length 36"

This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...

This pigtail fits left or right rear quarter power window switches and motor. Taken from an original used harness that had a Ford part number of D1ZB-14644-AB

Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.

Get your hands on the new, long awaited Mercury Cougar Eliminator book! Besides various specifics about "optional this" and "factory that", this book includes stories written by car owners. These stories remind us that our cars are more than just a collection of technical details. They link the cars directly to the people who own(ed) them. Why did they choose a Cougar and what impact did it have on their lives? Where did it come from and where is it now? Truly, the stories and history are the...

As seen in our YouTube video, this is a representation of the used, rebuilt and reproduction parts that we recommend you purchase to convert to disc brakes. If you do purchase this package we will insist on speaking with you prior to shipping as you may want to substitute parts based on what year your car is, manual or automatic. We also take in factory original drum brake spindles from 1971-73 cars.  Fun fact: 100% of all 1973 Mercury Cougars came with disc brakes from the factory. Check...

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

Hard to find New Old Recent Stock switch for the driver side power seat on the 71 - 73 Cougar or Mustang. Toggle switch looks accurate, however, you will need to reuse your original plugs. PLUGS NEED TO BE CHANGED FOR SPECIFIC APPLICATION. Some of the Ford part numbers include: D1WB-14B723-AA, D1WB-14B723-Ab, D2WB-14B723-AC, D1ZB-14B723-AA, D1ZZ-14A701-A, D2WY-14A701-A.

Used bezel for the driver side power seat switch on the 71 - 73 Cougar or Mustang. Ford part number D1ZB-14A706-AA This icon means that we're looking to buy this part! WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Wiring harness segment to the convertible power top pump on any 1971-73 Mercury Cougar or Ford Mustang. Part number D1ZB-15A668-AB.

Please allow up to two weeks for delivery. Reproduction one piece drive shaft for the 1967 - 1973 Mercury Cougar. Includes slip yoke and U Joints. Keep in mind that this repro drive shaft will only work on stock configuration cars. If the engine has been swapped, if you've had a different rear end installed etc., these drive shafts will not work. When ordering, be sure to specify (in the notes section) the year of your car, engine size and transmission type (automatic, 3 speed or 4...

Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

Used unique Phillips bright finish screw that attaches cable guides to roof.

Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut. 

Concours correct premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one, 31 inches, located on the driver side and is an exact fit for 1970 - 1973 Mercury Cougar and Ford Mustangs. Ford Part # D0ZZ-2A635-B

Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.

Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem, this part is the culprit! To test if your unit is worn grasp the driver side wiper arm and move the arm back and forth gently. If the passenger arm does not react to your every movement this assembly needs to be replaced. It is an easy to replace part in that you can remove the cowl panel behind your...

Single sheave crankshaft pulley. No options, one single fan belt around the crank shaft pulley, water pump pulley, and the alternator. Probably found on Boss 351, and other 351C cars without power steering or air conditioning.Pulley marked D1ZE-6312-AA.

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Used, chromed shock tower cap for the 1971-73 Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. We offer chromed versions of the shock tower caps for those that want to add some bling to the engine compartment.Ford part # D1ZZ-18A017-A.

Used headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang. Good used bezel with shiny chrome. May have one small nick in the chrome or one broken plastic stud on the reverse.Replaces Ford part number D1ZB-11649-AC.

Rebuilt quartz movement clock for the 1971 - 1973 Cougar or Mustang. Quartz movement clocks have second hands that click around, original clocks had a constant sweep of the second hand. NOTE: These clocks can be rebuilt with NOS movement for the same price, just mention it in the notes when making your order. Although Quartz movement clocks are reliable, NOS movement clocks are far more superior and smoother. Little differences like this matter if a car is being judged! ...

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This option requires that you send your core in advance. Your core gets rebuilt and returned. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A quality core must be complete and not overly corroded. We are unable to convert from non-low fuel to low fuel. We also...

This option requires that you send your core in advance. Your core gets rebuilt and returned. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality core must be complete and not overly corroded. We are unable to convert from non-low fuel to low fuel. We also...

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads.  If you're...

Rear most convertible top bow #4, from a 1971-73 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached.   Ford part number D1ZZ-7651278-A.

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.

Reproduction heater core tube gasket for the 1971 - 1973 Cougar or Mustang. Never sold as a service part by Ford, this gasket seals the area around the heater core tubes where they pass through the vehicle's firewall. The gasket is cut from closed cell EPDM foam sponge rubber that matches the original material used by Ford. Designed to withstand the temperatures found under the hood and surrounding the heater core tubes. ...

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket.