All Products

Motorcraft new old stock brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a service replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. C7ZB-13480-B Replaces Ford Part #: C9VY-13480-A.

NOS brake warning light switch for the Mercury Cougar or Ford Mustang that is identified by the single pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder, this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Ford part # C7AZ-2B264-A.

Used brake warning light switch for the Mercury Cougar or Ford Mustang that is identified by the single pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder, this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems.Ford part # C7AZ-2B264-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit...

NOS brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

New Old Stock passenger side door ajar switch for any 1969-70 Mercury Cougar or Ford Mustang with specific option. Standard on XR7, normally part of the convenience group option. Ford part number C9WY-14018-A.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

Door jamb switch for the 1969 Cougar or Mustang with a tilt column.

Used one year only door jamb mounted switch for activating the tilt column.

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

NOS, never been installed part they may or may not come with original box, will show shelf wear. Ford Engineering number stamped on the part is C8WB-11652-C.

May or may not come with original box, guaranteed to be never installed NOS. Ford engineering number stamped on part is C9WY-11652-B

Brand new in the Motorcraft box original FoMoCo part. Engineering number stamped in the part is D0WB-11652-B

These original FoMoCo headlight switches have been tested for both vacuum and electrical functionality. These old switches also come with the already attached "C" shaped spacer that mates to the dash. We all know how hard it is to get that spacer glued in on a new switch (which doesn't come with the spacer). Stamped witht the "Motorcraft" trademark and Ford part number C8WB-11652-C. 

C0TZ-13A024-A

This exact reproduction mounts to the rear of the factory installed heater control ventilation control panel. Save your knob or consider purchasing the 1969-73 selector button kit, find it here. Replaces Ford Part number C9ZZ-18578-A

This new old stock intermittent wiper switch has a two speed wiper function, but when turned counter clockwise, it has a rheostat that sets the different delay times. Switches can be physically marked with casting numbers of C9ZB-17A553-E, C9ZF-17A553-B or C9ZF-17A553-C. Any of which can be correct, and chances are, there are probably other casting numbers out there as well. This 69 switch has a total length of 3 3/8". A 1970 switch can be used, but the shaft is about 3/8" longer....

This used intermittent wiper switch has a two speed wiper function, but when turned counter clockwise, it has a rheostat that sets the different delay times. Switches can be physically marked with casting numbers of C9ZB-17A553-E, C9ZF-17A553-B or C9ZF-17A553-C. Any of which can be correct, and chances are, there are probably other casting numbers out there as well. This 69 switch has a total length of 3 3/8". A 1970 switch can be used, but the shaft is about 3/8" longer. Sometimes this...

High quality alternative to the expensive OEM switch. If you have an early 67 the plug may be the dual type which is also listed on this site. This will work with your C-4 or C-6 automatic transmission. The only real difference is that this switch does not come with the FoMoCo logo or part number on it. Replaces Ford Part #: C9ZZ-7A247-B, SW 877 

Tested and inspected neutral safety switch for the C-6 transmission installed in 1970 - early1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971.Look for a transmission code of U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: D1ZP-7A247-AA, or D0ZZ-7A247-B, SW 920.

Tested and inspected neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

C8AZ-14529-C

New old stock power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch. Stamped C8AB-14529-A. This is the 1 tab switch. However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

Compare your switch to these to insure you have the right configuration. Ford engineering number imprinted on the side is C9AB-14529-B.

Pull on switch assembly for the speed control option on probably the early system. Switch only, no knob. Ford part numbers C7WY-9A837-A and C7WA-9A837-A *Note – for use with factory cruise control.

NOS fixed column turn signal switch for the 1967 Mercury Cougar or Ford Mustang. This is a later service replacement turn signal switch, it may have an extra wire or two, and the wire lengths may be longer than the factory original. Ford part number C7ZZ-13341-F Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....

NOS fixed column turn signal switch for the Mercury Cougar or Ford Mustang.Ford part # C9AZ-13341-R.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

NOS fixed column turn signal switch for the 1970 - 1972 Mercury Cougar or Ford Mustang.Ford part number D2AZ-13341-CNeed help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Replacement turnsignal switch for all 1968 Mercury Cougar and Ford Mustang with fixed (non-tilt) steering columns. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to...

Used Turn Signal Switch / Fixed Column for the 1969 Mercury Cougar / 1969 Ford Mustang 

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

NOS switch and bracket for the emergency / parking brake. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A

Tested and working emergency / parking or parking brake indicator switch and bracket. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Tested and working emergency or parking brake indicator switch. Foot parking brake switch found on 1971-73 Mercury Cougar and Mustang. This particular switch is also found on various other Ford/Mercury products starting in 1970. Ford part number D0AZ-15A851-A.Includes bolt to attach to emergency foot brake.

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...

These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...

These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...

These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

The following excerpt was taken from the advance summary sheets mailed to dealers in 66 and 67.- "For when your customer feels like putting his foot down! Cougar has got a heart of "GO" - just as it comes from the factory. But there are bound to be buyers who will get under the hood to sharpen Cougar's claws. To satisfy the needs of these high performance buffs, here are a number of performance equipment items designed especially for Cougar by Shelby American, Inc. We suggest you stock a...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13441-AA ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13441-AA