All Products

Pair of reproduction cowl vent panel support pads.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the right hand or passenger side spring that holds the rear license plate or fuel door in the upright position. Fits 1967-68 and 1971-73 Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-A

This is the spring that holds the rear license plate or fuel door in the upright position. Fits 1969-70 Cougar.Ford Part #: C9WY-13455-A

Good aluminum piece that has no corrosion, no dings and all six mounting studs will be firmly in place. This same bezel was used on all Standard, XR7 or Eliminator Cougars for 1969 and 1970. Obviously the clock hole was not utilized on the Standard Cougar.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

C9ZZ-5482-D Factory used sway bar for any 1969 Cougar with optional Competition Handling Package. Factory identified with a single 'Green' paint stripe. *Excludes 428CJ and Boss 302 cars, those cars were factory built with a 15/16 inch sway bar. This factory used front sway bar, does not include any mounting brackets or end link kits.

C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

Used front sway bar, does not include any mounting brackets or end link kits. Ford part # C7WY-5482-A.

D1ZZ-5482-A Very briefly at the beginning of the 1972 model year 9/1/1971 - 10/11/1971. Specifically marked from the factory with 1 Violet and 2 Yellow paint stripes. This factory used front sway bar, does not include any mounting brackets or end link kits.

D0ZZ-5482-B Factory used front sway bar found on most 1970 Cougars. 3/4 inch in diameter. This factory used front sway bar, does not include mounting anybrackets or end link kits.

C9ZZ-5482-A 1969 Standard used factory front sway bar. 3/4 inch in diameter. This factory used front sway bar, does not include any mounting brackets or end link kits.

For any 1971, 1972, 1973 Mercury Cougar. The 1/2" sway bar for Competition Handling was optional on any 1971-73 Cougar, but it was included automatically on all 1971 GT's, 429 Cobra Jets, and with the 1972 & 1973 Q code engine option (351CJ). Concours restorers, should be painted all chassis black with 1 White stripe. This factory used 1/2" rear sway bar, does not include any mounting brackets or end link kits. Replaces Ford part number D1WY-5A772-A.Here's our little film to help you...

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on your Mercury Cougar or Ford Mustang. Good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit.Ford part # D1ZZ-19986-A.

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

Used air conditioning thermostat switch for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Ranco for Ford. Ford part numbers C7ZA-19618-C or C7ZZ-19618-A.

Used air conditioning thermostat switch for any 69-70 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part number C9ZA-19618-A

Used air conditioning thermostat switch for any 1971-73 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part numbers D1ZA-19618-A or D1ZZ-19618-A.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573.*Note - 3 speed switches are different than the 4 speed switches.

Reproduction backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Replaces Ford part number C7ZZ-15520-A.*Note - 4 speed switches are different than the 3 speed switches.

Reproduction Backup Light Switch / Manual Transmission / 4 Speed for the 1969 Mercury Cougar / 1969 Ford Mustang 

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with power brakes. High quality replacement brake light switch, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: D1ZZ-13480-B.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a high quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: C9VY-13480-A.

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

D0AZ-2B264-A Identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems.

This switch mounts on the brake junction block to warn the driver of potential brake failure through a warning light on the dash. Replaces Ford Part #: C8AZ-2B264-A.

Used brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

NOS one year only column mounted switch for activating the tilt column. Ford part number C7ZZ-13713-A

Used one year only column mounted switch for activating the tilt column.Ford part number C7ZZ-13713-A

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Replaces Ford Part #: C8OZ-13713-A.

New Old Stock switch for the 1967 Mercury Cougars and Ford Mustangs that came with the 3/4" door jamb switch. This switch will be yellowed from age. Additionally, this switch for the 3/4 inch mounting hole was used on 1965-66 Full sized Ford such as Custom, 500, Galaxie, and XL models, full sized Mercury such as Monterey, S-55, Montclair, and Park Lane. 1965-67 Fairlane, 500, XL, Ranchero, and GT. 1965-67 Mercury Comet, 202, Capri, Caliente, and Cyclone. 1965-67 Ford Mustang, 1965-67 Ford...

Nice reproduction of the 1967 Door Jamb Switch. Replaces Ford Part #: C5AZ-17317-A Please note that most of the plastic bodied, reproduction door jamb switch currently available are for the later model cars and have smaller female plug holes that will not work on a 67.

This is a good used switch for the 1967 Mercury Cougars and Ford Mustangs that came with the 3/4" door jamb switch. This switch will be yellowed from age. Additionally, this switch for the 3/4 inch mounting hole was used on 1965-66 Full sized Ford such as Custom, 500, Galaxie, and XL models, full sized Mercury such as Monterey, S-55, Montclair, and Park Lane. 1965-67 Fairlane, 500, XL, Ranchero, and GT. 1965-67 Mercury Comet, 202, Capri, Caliente, and Cyclone. 1965-67 Ford Mustang, 1965-67...

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.