All Products

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. There are few differences between the 1969 and 1970 conversion kit. This kit consists of an electric actuator assembly (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable...

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. There are few differences between the 1969 and 1970 conversion kit. This kit consists of an electric actuator assembly (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable...

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

Used electrical contact kit for the foot operated electric wiper actuating device. Most times these contacts have been fried, so instead of replacing the whole pedal you can now replace the electrical portion of the pedal and get it back to working condition.

This is a digital copy of the installation instructions and troubleshooting guide that comes with the 69-73 electronic sequential units that we sell. Click here to view the Low Quality version of this Trouble Shooting Guide. Add it to your cart to download the High Quality version of this Troubleshooting Guide.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Reproduction complete electronic sequential system for the Ford Thunderbird produced after Jan. 16th, 1967. This unit does not come with the stop lamp relay and is a special order item only.*NOTE* Need help diagnosing a turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Reproduction complete electronic sequential system for the Ford Thunderbird produced before Jan. 16, 1967. This unit includes the stop lamp relay. *NOTE* Need help diagnosing a turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

There never was an Eliminator convertible from the factory, but we think there should have been. Since the rear quarter panels are shaped differently, we redesigned the side stripes to fit the contours of the convertible Cougar correctly. Otherwise, these are the same stripes we sell in coupe format, cut from OE-spec 3M Scotchcal vinyl and designed from a NOS stripe kit. The kit includes 17 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, ELIMINATOR rear quarter...

This is our complete black stripe kit for the 1970 Cougar Eliminator. The kit includes 17 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, ELIMINATOR rear quarter panel decals, and the often-overlooked 3-piece rear trim blackout stripes. This is the most correct and complete kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same 3M satin black vinyl that Ford used from the factory. *Convertible owners - If you're planning...

Black stripe kit for the 1969 Cougar Eliminator. This is the most correct kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same 3M satin black vinyl that Ford used from the factory. Kit includes 8 pieces for the fenders & extensions, doors, and quarter panels.Copy of original Ford decal instructions included. Note that these stripes are supposed to go on in a straight line, they do not curve down with the body line. See car picture in this listing for...

There never was an Eliminator convertible from the factory, but we think there should have been. Since the rear quarter panels are shaped differently, we redesigned the side stripes to fit the contours of the convertible Cougar correctly. Otherwise, these are the same stripes we sell in coupe format, cut from OE-spec 3M Scotchcal vinyl and designed from a NOS stripe kit. Quality and fit are second to none. There was also never a white Eliminator stripe kit in 1970 (unlike 1969) but we figured...

This is our complete white Eliminator stripe kit for 1970 Cougar coupes. There was never a white Eliminator stripe kit from the factory in 1970 (unlike 1969) but we figured we'd make these available for those wanting a custom look. Designed using a NOS stripe kit as a reference, and cut from OE-spec 3M vinyl, fit and quality are second to none. The kit includes 14 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, and ELIMINATOR rear quarter panel decals. Unlike...

White stripe kit for the 1969 Cougar Eliminator. This is the most correct kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same kind of 3M vinyl that Ford used from the factory. Kit includes 8 pieces for the fenders & extensions, doors, and quarter panels.Copy of original Ford decal instructions included. Note that these stripes are supposed to go on in a straight line, they do not curve down with the body line. See car picture in this listing for...

This pair of tail light bezels have been chemically dipped to remove the chrome and are ready to be painted black for your 1970 Resto-Mod or 1970 ELIMINATOR. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved (mostly on the top edge) before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no...

Used 14x6" Eliminator wheel with a chrome center and a painted rim for the Mercury Cougar or Ford Mustang / Torino. This chrome version was never used on a factory ordered Cougar, but you could order it as an over the counter upgrade as shown in 1968 dealer promotional literature. Total width is 7" and the backspacing is 4". Click here for the hubcap and trim ring we recommend for this wheel.

Used 14x6" Eliminator wheel that had a painted center and rim from the factory for the Mercury Cougar or Ford Mustang / Torino. For those wanting original FORD dated codes and riveted together construction (reproductions are welded) this is a good used wheel in need of paint. Center cap and trim ring sold separate. Click here for the hubcap and trim ring we recommend for this wheel. Ford part # C8OZ-1007-J.

Reproduction 15x8" Eliminator wheel with a painted center and rim for the Mercury Cougar and Ford Mustang / Torino. This wheel will look great on any Cougar and is a great way to fit some serious rubber under your Cat. Click here for the hubcap we recommend for this wheel.*NOTE* Please allow 4 to 5 weeks for delivery. ...

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

Used Grade A condition 6.5 litre (390) aluminum fender emblem / badge for the 1967 Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured with several small blemishes. Often, one of the two studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390. On other Cougars, they were used on those that came equipped...

Used 6.5 litre Grade A (390) fender emblem for the Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured on our grade B listing with several minor blemishes. No studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the...

Used Grade B condition 6.5 litre (390) aluminum fender emblem / badge for the 1967 Mercury Cougar. We rarely get these in good condition and most of what we get looks like the one pictured with several pits and small blemishes. Often, one of the two studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390. On other Cougars, they were used on those that...

Used Grade B 6.5 litre (390) fender emblem for the Mercury Cougar. Most of what we get looks like the one pictured with several blemishes. Often one or more of the four studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. We also have...

Reproduction 6.5 litre (390) fender emblem for the Mercury Cougar. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. Unlike the originals these do not have mounting studs, but are firmly held in place with 3M VHT double sided emblem tape.

Good used pit free emblem that would be good for restoration. Notice the clips are in place and there are no cracks in the plastic backing. The example picture of the installed emblem is what they looked like when restored. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.

This used grade A emblem will have good chrome and mounting studs and plexi center. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

This used grade B emblem will have good chrome and mounting studs, but the plexi center will be faded. These can be opened up and repainted from the backside. The paint can be obtained from stores that sell modeling supplies. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. ...

Used Grade "B" center grille emblem for the 71 - 72 Standard Cougar. Will have fading, pitting and the plastic lens area will need to be restored. Ford part number D1WY-8A223-A

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Located on the right hand dash panel of your XR7, requires drilling to remove properly.

Good used plastic emblem with no peeling chrome. This was used on all models except XR7 on the right side. We also have the metal version of this emblem available.

Grade "A" pit free original metal emblem for your Eliminator or Standard model Cougar. If you look closely at our picture you will in fact see tiny imperfections in the chrome. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Grade "B" original metal emblem for your Eliminator or Standard model Cougar. Grade B emblems will have pitting and faded or missing paint. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

Grade A used, trunk emblems for 1969-70 XR7 models. We will very seldom have this in stock, the alternatives are grade B used or reproduction. Please see related items below. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both...

Due to corrosion caused from the exhaust this used emblem will most likely have poor quality chrome. The emblem shown would be the very rare exception.

Will show at least a small amount of pitting. Casting number as seen on the back reads D0WB-652803-E.

Used driver side (left hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Used passenger side (right hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually.

Used XR7 door panel emblems for the Mercury Cougar. The emblems shown are not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold as a pair.

Left is the same as right, one year only emblem at the center top of the door panel. Usually will show a small amount of pitting. Casting number as seen on the back reads D0WB-6520802.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T. Technically this is the version found on 1967 cars, the 1968 versions had a larger blue oval 'Ford', and did not have the 'Product of' line.

These fender emblems look much like the 1968 quarter panel emblems but differ in that they have longer studs that fasten via barrel clips as opposed to a speed nut used on the 1968 quater panel emblems. The Ford casting number on the backside is D1WB-16098-AA. For the money, The 1968 repro quarter emblem is a much better buy . ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used.Ford part number C7GY-16098-BFord Casting number C7GB-16720-B ...