All Available Parts - 1966 Ford Mustang

This system features the "Original" Baer 2-piston, pad guided caliper (PGC) mounted to a 13", 1-piece slot, drill, zinc plated integral hub rotor. The PGC caliper comes in a red powder coated finish with a black logo, includes dust/weather seal's and uses the popular D412 pad type. The system includes premium bearings with races pre-installed, dust caps, mounting brackets, stainless braided hoses and all necessary hardware. The 13" "Classic" system fits select 17" or larger wheels....

This system features the "Original" Baer 2-piston, pad guided caliper (PGC) mounted to a 11.29", 1-piece slot, drill, zinc plated integral hub rotor. The PGC caliper comes in a red powder coated finish with a black logo, includes dust/weather seal's and uses the popular D412 pad type. The system includes premium bearings with races pre-installed, dust caps, mounting brackets, stainless braided hoses and all necessary hardware. The 11.29" "Classic" system fits select 14" and most 15" or larger...

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Stamped Steel Pointer Mounts to Timing Chain Cover. Black Zinc-Plated. Includes Mounting Screw. Correct for 289, 302 and 351W Mercury Cougar or Ford anything including Mustang. We know the other vendors claim this part to fit 1967-73, but it doesn't. Works with 1968-69 Ford timing covers and with 1968-69 Ford 3 bolt harmonic balancers. Starting in 1970, Ford V-8 engines for Mustang and Cougar had timing pointers installed on the passenger side of the engine, and used harmonic balancers with 4...

Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339

Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...

Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown. 

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

Single cylinder head from 1967 Mercury Cougar with non smog 289 engines, 289-2V and 289-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 54-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.3:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C6OE-M or C6OE-6090-M.These weigh...

Reproduction washer for the interlock on all top loader 4 speed transmissions as found on 1967-69 Mercury Cougar and Ford Mustangs.Ford part number C5ZZ-7C318-A.

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  NOS power steering control valve seal kit.  Ford part number C3AZ-3A650-B. ...

NOS distributor lead wire without the boot for the coil. There were at least two different lengths of wire leads found on 1967 Mercury Cougar and most all other Ford and Mercury distributors. This is the longer wiring harness, about 20 inches outside of the distributor. Direct replacement for 1961-67 Ford distributors.Ford part number C1VF-12216-A.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.

New rubber boot for brake push rod to the master cylinder on all drum brake cars. Fits all 1967-72 Mercury Cougar and 1965-73 Ford anything cars, including Mustang.Trivia - Did you know that 100% of all 1973 Mercury Cougars, came from the factory with front power disc brakes?

Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.

GT 350 Holley 715 CFM center pivot bowl to bowl transfer tube. This is not for a regular Holley 4150. These tube ends are about 12-1/2 inches apart. Dual quads?

***WARNING*** Plugging these directly into a Cougar wiring harness without correctly re-wiring in the pigtails may fry your wiring harness! Reproduction driver side (left hand) and passenger side (right hand) front turn signal / parking light assemblies for the Ford Mustang. The plug is not correct for the Mercury Cougar's wiring harness and will need to be changed to work properly. However, this is an easy straightforward process which we lay out below. Plus you can save a good amount of that...

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

New thread sealant specially formulated to seal liquid in high temperature applications.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out this video ...

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

New Old Stock 1967-68 Mercury Cougar and 1966-68 Ford Mustang clutch release fork to equalizer spring. Upper clutch equalizer to firewall, 289 and 302 engines. This unit will also work for 1969-70 Cougar and has the correct spring hook orientation. 66 - 68 Ford specs: 3-1/16" Long 40 Coils 69 - 70 Ford specs: 3-1/8" Long 36 Coils Ford part #: C6ZZ-7591-A.

Detachable mounting plate for installing the driver side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A19-A.

Used passenger side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired. Ford part number C4ZB-7650534-C.

Used driver side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired.  Ford part number C4ZB-7650535-C.

Complete floor pan for the 1965-68 Ford Mustang. NOTE: Can be made to fit 67-78 Cougar, Included seat risers are Mustang versions, which are taller than the Cougar seat risers. We recommend re-using your original Cougar seat risers, unless you want the extra height of the Mustang risers. Also note that the risers included with this floor pan will not be attached, you'll have to weld them on. Keep in mind Cougar has a longer wheel base which make the portion under the back seat substantially...

* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

Reproduction brackets to hold the junction of the steel brake line and the rubber brake hose. Mounts to the frame rail. Fits 1967 Mercury Cougar and 1965 - 1967 Ford Mustang with factory installed Kelsey Hayes 4 puck disc brakes only. These are manufactured 30 thousandths thicker to compensate for the missing flange that the originals had along the sides.  Replaces Ford part numbers C5ZZ-2082-D and C5ZZ-2082-C

New metal clips to replace your worn out original fuse holders.

Great chrome on this reproduction backup / reverse light for the passenger side (right hand) of the the Mercury Cougar or Ford Mustang. Lens, gasket, and bulb sold separately. Replaces Ford part # C7ZZ-15511.

Great chrome on this reproduction backup / reverse light for the driver side (left hand) of the Mercury Cougar or Ford Mustang. Lens, gasket, and bulb sold separately. Replaces Ford part # C7ZZ-15512.

Reproduction amber parking light / turn signal lens. This was actually used on the 64 - 66 Mustang which used the amber lens and clear bulb, as compared to the 67 - 68 Cougar which used the clear lens and amber bulb. Sold without gaskets or hardware (see related items).Sold individually

Reproduction distributor lead wire without the boot for the coil. There were at least two different lengths of wire leads found on 1967 Mercury Cougar and most all other Ford and Mercury distributors. This is the longer wiring harness, about 20 inches outside of the distributor. Direct replacement for 1961-67 Ford distributors.

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.

New Old Stock upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

Reproduction upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Replaces Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

Set of 12 bolts for the intake manifold on any factory 1966-67 Ford 289 engine. AMK F-478.*Note - Excludes 1968 289 and 302 engines.

Known to have been used on 1969-1970 air conditioning boxes to hold a vacuum hose to the actuator.  They can be screwed or bolted to the plenum.   Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4193S. This is the early style with "CAR bure TER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with A or C code 289 engines and 1966-67 Ford and Mustang with A or C code 289 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and...

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4193S. This is the late style with "CARTER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with A or C code 289 engines and 1966-67 Ford and Mustang with A or C code 289 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...

Windshield washer hose clip that holds the hose up under the cowl. Concours quality

C4ZA-3590-A Early 1967 Steering box pitman arm with 1 inch sector shaft. Power steering only, used with SMB-E steering box. Fits early 1967 Mercury Cougar and 1965- early 1967 Ford Mustang. Ford part number C5ZZ-3590-A. Caution, measure your steering box sector shaft, many of the short boxes have been changed to the 1-1/8 inch boxes. Rare part, limited to stock on hand. Check out this video

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

Reproduction power steering control valve boot and clamp, for the 1967-70 Mercury Cougar or 1965-70 Ford Mustang. Gold tone clamp, molded rubber boot, and pair of screws. Very accurate reproduction. 

Features quality stamped steel construction, bushings, nuts, anti-squeak coil protector pads. From the get go these were never a very good design... The rubber is prone to cracking and the unit will bind under severe use. Not just speaking of the unit we are offering but all of them including the original Ford units. Here is an interesting article for those that are not happy with status quo. Global West and others have come up with their own solutions and after we have spent more time testing...

High Performance Coil Spring Perches offer a very affordable upgrade to stock spring perches with rubber bushings. These are made with synthetic elastomer bushings which are similar to polyurethane in performance and longevity, but will not squeak like polyurethane. The perch can rotate 360 degrees on the shaft, which allows the front suspension to articulate freely. This feature also eases the installation of the coil spring. Zerk grease fittings are installed and locking nuts are included....

Bare cast aluminum C4 transmission case from a 1967-68 Mercury Cougar or Ford Mustang. Inspected for damage. Replaces Ford part number C6DP-7006-A.

Used servo cover from a 1967-68 Ford C-4 transmission. This cover has the big A cast into it, which designates it as an "A" Intermediate Servo Band Cover. Typically, this cover would be found on C4's, with Mercury Cougar and Ford Mustangs with C code 289-2V, A code 289-4V, or F code 302-2V engines. Cover only, marked C6AP-7D027-C.

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

Top Loader transmission input shaft seal, small shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University.*Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

Top Loader transmission rear seal, 28 splined shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University. *Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

This version with a cast head was only found in the earliest 1967 Mercury Cougars. 13/16 inch socket. Much better quality than the later stamped steel version.

Reproduction spare tire hold down kit for the 1967 Mercury Cougar or 1965 - 1967 Ford Mustang. Included in the kit are the wing nut, hold down disc and the J bolt. Exact reproductions of the originals. Check out this video

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Application 289-4V auto and 289-2V manual transmissions at the beginning of the 1967 model year. Pulley diameter 4 inches, 1967 smog pulleys are unique in that they have 4 mounting holes. Ford part number C6OZ-9B447-A and engineering number is C6OE-9B447-A or B. *California DSO 52 and DSO 53 only.

Used Wittek #88 clamp. Originally was Zinc Dichromate plated. This used clamp was used for attaching the air inlet filter assembly to the inlet bracket. 1966-67 Ford and Mercury cars and light trucks with Thermactor smog systems. Typically found on California sold vehiclesWittek manufactured their part number is 88 and it is stamped as such. The Ford part number is 97289-S. This information was found in the 1967 Engine Assembly Manual.

Used Wittek #92 clamp. Originally was Zinc Dichromate plated. This used clamp was used for attaching the air inlet filter assembly to the inlet bracket. 1966-67 Ford and Mercury cars and light trucks with Thermactor smog systems. Typically found on California sold vehicles. There is also a Wittek 88 clamp, which is slightly smaller. Wittek manufactured their part number is 92 and it is stamped as such. The Ford part number may be 97289-S. This information was found in the 1967 Engine...

New Old Stock neutral safety switch for the C-4 transmission installed in early 1967 Mercury Cougar and 1966-67 Ford Mustangs. Found on cars before build date 12/15/1966. This neutral safety switch is identified by having two plugs that plug into the single 4 pin plug, coming from the firewall. The later neutral safety switch with a single 4 pin plug will also work fine.Look for a transmission code of W on your door data plate. If your car has a code U, your original transmission was an C-6...

Dash to engine Gauge Feed with push-on post oil sender and Air Conditioning. Should be for 1966 Falcon and Mustang. Replaces Ford Part #: C6DZ-14289

Aluminum casting, made in the U.S.A. Exact copy of original, including part numbers. Fits any small block Ford 260/289/302/351W but would have only been correct on 1967 Mercury Cougar and 1965-67 Ford and Mustang with 289 engines. Has natural cast finish as original. Does not have the provision for the thermal vacuum switch starting in 1968 and newer small block Ford V-8 engines. Replaces Ford Part #: C5OE-8592-A For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check...

NOTE* After comparing to the original pulley, we've found that this reproduction is approximately 3/16" shorter in overall height. New crank shaft pulley, single sheave small block Ford 289 / 302 351W engines up to 1969. Single V-belt or fan belt pulley, means for use with only the alternator. Not for use with power steering, air conditioning, or smog pump. Measures just under 6-1/4 inches in diameter. Single sheave crank shaft pulley with 3 bolt holes, excludes engines after 1970....

This is a single plug (standard models without low fuel warning light) fuel sending unit with an extra bung for a return line for 1967-68 Cougars and Mustangs running fuel injection. No need to change the whole tank in order to upgrade your car to fuel injection!  Main line 3/8" Return line 1/4" Check out the video below on our new gauge tester: ...

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Nut for attaching the steering wheel on any 1967 Mercury Cougar or 1965-67 Ford Mustang.Ford number 350983-S.

Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

Power steering hose bracket for early model Mustangs.

Reproduction shifter assembly for the Mercury Cougar or Ford Mustang equipped with the automatic transmission, but without a center console. Check out our video on rebuilding your shifter below: ...

Original dipstick or in Ford speak "Indicator - Oil Level" for C4 automatic transmissions. Application for 1967-68 Mercury Cougar 1966-70 Ford Mustang with 289/302 engines and C4 automatic transmissions, code "W" on your door data plate.Ford part # C6OZ-7A020-B.

This great little kit replaces stock Ford bushings that can wear out in as quick as one year. This is a very simple repair and upgrade, once you have removed the pedal support from the car. Upon completion of this you will be rewarded with greatly reduced pedal pressure and the knowledge that you will never have to replace these bushings again. This is a must have for anyone with a manual transmission.Does not fit 1971-73 Mercury Cougar or Ford Mustang.

This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit.Repairs 1967-70 Mercury Cougar or 1965-70 Ford Mustang. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are swedged in. * Does not fit 1971-73 Mercury Cougar or Ford Mustang.

This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit. Repairs 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Plus many other Ford cars.This kit requires welding. For use on pedal hangers that are all wallered out, or 1971-73 pedal hangers that are not round. Kit has roller bearings. Quality Scott Drake / Holley product. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are...