Your cart is empty!
Reproduction "A" pillar repair panels for your 67 - 68 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.
Replaces Ford part # 380771-S
New 2.5 amp Buss style glass tube fuse for the Mercury Cougar or Ford Mustang. This fuse was used for 1967-68 only and is used for the instrument panel, clock and ashtray lights. This unit measure about 5/8" long and is sold individually.
Miniature light bulb for any 1967-68 Mercury Cougar or Ford Mustang with the door ajar feature. Original equipment GE 256 light bulb. This is a flashing light bulb. It has a metal strip that heats up and breaks contact for a flashing effect. Starts out with the bulb on, and eventually starts flashing over a period of a few seconds.
Reproduction 289 / 302 2V AT / MT Emission Decal for the 1968 Mercury Cougar or Ford Mustang
Reproduction 289 - 302 Alternator Bolt w- Smog for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold individually
Concours correct Autolite spark plug wires for any 1968 Mercury Cougar or Ford Mustang with 289 or 302 engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q67 (second quarter 1967) on the 7mm wires. Black spark plug boots on this set.
Small block dipstick tube for the 1968 Cougar and Mustang. Nice chrome finish to catch the eye. Will also fit on 1969 Mustangs with a 302 engine.
Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.
part # C2OZ-6065-A. Shorter of the two head bolts.
part # C2OZ-6065-B. Longer of the two head bolts.
Exact Reproduction 289 Hi-Po Main Cap Set offered by Ford. They are cast and machined here in the USA from the original Ford blueprints. A set consists of caps numbered 1- 4 and requires the use of an original rear main cap to finish an engine. These caps are cast from the highest quality Nodular iron and machined for ease of fitting to any 289 block. The I.D. of the main bearing bore is .020 undersize and the side registers are .010 oversize on each side for proper adjustment before line...
Mounts onto the transmission. Fits all 1967 - 1968 8 Cylinder.
Used 3 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for seat belts and door ajar indicators. Blue and red light sockets. These are the same sockets for the seat belt reminder and door ajar warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.
Are you looking to replace or upgrade your complicated 1968-70 3 Point Seat Belts with a modern easy to use factory looking Belt? These 3 Point Seat Belts will bolt onto any 1968-1970 Coupe using your existing mounting hardware... The belt buckles are very similar to the original Starburst buckles Ford used in the Late 1960's. Please keep in mind that although these are called "Parchment", they are more of a light brown / tan color. Although these belts are nice aesthetically, they don't work...
Are you looking to replace or upgrade your complicated 1968-70 3 Point Seat Belts with a modern easy to use factory looking Belt? These 3 Point Seat Belts will bolt onto any 1968-1970 Coupe using your existing mounting hardware... The belt buckles are very similar to the original Starburst buckles Ford used in the Late 1960's. Although these belts are nice aesthetically, they don't work very well. NO RETURNSCheck out our video on everything seat belts below: ...
Reproduction 3-Speed Transmission Instruction Tag for the 1967 - 1968 Mercury Cougar / Ford Mustang
Replaces Ford Part #: C8DE-9C485-C
Reproduction 390 / 428 4V AT / MT Emission Decal for the 1968 Mercury Cougar / Ford Mustang
3/8-16 X 7/8 9/16 AF .75 OD Sold individually. Fits all 390 & 428. Replaces Ford Part #: 374409-S.
OEM Style Oil Pan Gasket.
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds
Used 4 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for parking brake and low fuel indicators. Yellow and green light sockets. These are the same sockets for the parking brake and low fuel warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in you Cat? The video...
New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.
New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Concours correct Autolite spark plug wires for any 1969 Mercury Cougar or Ford Mustang with 428CJ engine with thermactor smog system. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Orange spark plug boots on this set.
Decal Text: Autolite EV-45 C8OZ-6A666-B Replaces Ford Part #: C8OZ-6A666-B.
Reproduction 60000 Mile 6 Month Lube Sticker for the 1967 - 1973 Mercury Cougar / Ford Mustang
This kit contains all the replacement springs and hold down components required to do a professional job on rear drum brakes. Kit includes enough parts for two wheels. This is for the 9 inch drum brakes commonly found on the early 6 cylinder cars with 7-1/4 inch rear ends.*Note - Kit does not include hardware for rear emergency brakes.
Reproduction driver side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.
Reproduction passenger side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.
These selector buttons are top quality reproductions with a lot of attention given to the details to make these little units look factory fresh and correct.
Seals the hole where the A/C lines pass through the core support on the driver side on Mercury Cougars and Ford Mustangs. Replaces Ford part #: C7ZZ-19810.
Air conditioning fan blower assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.
Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...
York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...
These are correct reproductions of the A/C discharge service valve that comes with plastic caps. if you would like the correct aluminum valves, we sell those separately.
Redesigned modern evaporator has 35% MORE PASSES, using three-circuits, instead of the original single-circuit design. This is a direct bolt-in replacement and requires no modification.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal. It has been our experience that these often fail within a few years. We suggest flushing and pressure...
Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what...
Exact replacement for your original dryer and should be changed anytime the system is recharged. This stainless steel filter element is the life of your system and stops contaminants from clogging the expansion valve. Painted the correct satin black.
Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade B vents will mostly have a missing metal bracket and / or small crack or break usually around the mounting holes.
Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Nice fit, made of plastic. Will work with or without console, has slightly wider wings for clearance of the rear of the factory installed consoles.
Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs without a console.
Concours correct A/C discharge hose for Mercury Cougars and Ford Mustangs.Replaces part # C7AZ-19972-A or C7ZZ-19972-A.
Regardless of which V-8 engine, C8ZA-19835-A or C8ZA-19837-A both can be the correct part number. This hose is approximately 74 inches long. This hose also incorporates the site glass. The Ford MPC # is C8ZA-19835-A or C8ZA-19837-A.