Exhaust

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Reproduction pair of exhaust pipe clamps for your 67 - 69 Cougar or Mustang.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

Concours correct engine pipe donut, metal, factory original dual sized design to properly seal H-pipe to Exhaust manifolds MCA approved, sold individually.Replaces Ford Part # C8LV-9450-AFits between exhaust manifold and header pipe (H or Y pipe) 2 1/16 id 3 5/8 od cast iron, tapered top and bottom, smooth inside.Note! These are very difficult to seat compared to the pliable ones we sell. If you do decide to use the steel version it is recommended you apply a liberal coating of Permatex High...

Exhaust manifold flange rings or 'doughnuts' for stock cast iron 428CJ exhaust manifolds. These are the malleable type that conform and slightly crush. Inside diameter just over 2-1/8 inches. Sold individually, two needed per car.

Factory cast iron exhaust manifold set, both right C6OE-9430-E and left C6OE-9431-F side exhaust manifolds. Same manifold for all 289 and 302 engines for both 1967 and 1968. Random date codes.

C6OE-9431-F Factory original cast iron exhaust manifold for driver side. Ford manifold used on all 1967 and 1968 289/302 engines.

C60E-9430-E Factory original cast iron exhaust manifold for passenger side. Factory Ford manifold used in both 1967 and 1968 for all 289 and 302 engines. The heat riser stud will not be broken off like most. If this not a concern to you and want to save money please let us know!NOTE* Item has been sand blasted for pictures. The manifold you will get will be off of a parts car and will need cleaning.

Factory original cast iron exhaust manifold for passenger/right side. For both S & X code 390 engines and W code 427 GT-E engines manufactured after 2/15/1968.Ford part # C8OE-9428-C.

C8OE-9428-A Factory original cast iron exhaust manifold for passenger side. Cast number C8OE-9428-B is also acceptable for 1968. Current manifold has a legible casting date of 5/4/1968. Happy Star Wars day.

Spot on reproductions made of higher quality steel that OEM!

Reproduction high performance cast iron exhaust manifolds for the 1967 - 1968 Cougar or Mustang equipped with the 289 or 302 engine. Designed to be exactly like the originals, with correct markings and raised part numbers. Includes studs and nuts.Replaces Ford part numbers C6OE-9430-E and C6OE-9431-F

390-2V, 390-4V, and 427-4V factory cast iron exhaust manifold set, both a correct right and left set of matching exhaust manifolds. Indicate in the comments section if you want the early 1968 passenger side with C7OE-9428 casting or late 1968 with C8OE-9430 casting.

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. These manifolds are available in both early and late versions. The earlier version manifold has the correct spacer on the right side while the later version manifold does not.  Installs easily and eliminates clearance issues compared to headers....

These are not concours correct, but still look good. "Pipe within a pipe" chrome plated 14 gauge steel.Replaces Ford part number S8WS-5232-A.

Correct black phosphate bolts for use with 289 HiPo (K-code) exhaust manifolds. Although Cougars never offered a HiPo 289, the HiPo manifolds will fit any 67-68 289 or 302.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds. 390 and 427-4V engines without exhaust heat risers. That kit would include a studded bolt for the heat shield. See item 41282.

This direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang equipped with either the 289 or 302 engine and stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 289 or 302 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems...

Direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2 inch...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1968-69 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1968-69 Cougars and Mustangs with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for...

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1968-69 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from original 1968-69 Cougars and Mustangs with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the...

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

Very rare one year only heat riser "S" shaped metal tube that attaches to the heat shield on the passenger side front portion of the exhaust manifold. Correct for all 1968 Cougars equipped with the 390 cubic inch engine.Ford part number C8AZ-9652-A.

*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...

C8AZ-9A603-C metal shroud and tube assembly that attaches to the factory 1968 air cleaner assembly on all C code 289-2V engines as well as F code 302-2V, and J code 302-4V engines all for 1968. We do not believe that this set up came with the Canadian export Cougars, those 1968 Cougars should have the closed PCV system, much like the 1967 49 state Cougars.Do to age and their location our used risers will have minor surface rust, but otherwise be in good condition. Reproduction version of this...

C8AZ-9A603-C metal shroud and tube assembly that attaches to the factory 1968 air cleaner assembly on all C code 289-2V engines as well as F code 302-2V, and J code 302-4V engines all for 1968. We do not believe that this set up came with the Canadian export Cougars, those 1968 Cougars should have the closed PCV system, much like the 1967 49 state Cougars.Do to age and their location our used risers will have rust and or be very thin in spots. Reproduction version of this part is no longer...

Very hard to find, one year only part that is not currently reproduced. These came on 1968 Cougars equipped with the "S" code 390 and the "X" code 390. Must have for that show quality GT or XR7-G. *NOTE* Please keep in mind that our hard to find parts like this are not always competitively priced with what you will find on the open market at swap meets and private party sales. Our primary intent in listing these is for our customers to use this website as a resource to properly identify parts...

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

Sold individually Zinc (Dark Silver)

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

Used exhaust manifold spacer without butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Straight factory used spacer. Most cars came equipped with a thermal spacer that often times gets frozen with time. No obstruction with this one.Note - Does not fit the slightly larger 428CJ exhaust manifolds. Ford part number C6OZ-9A427.

Used exhaust manifold spacer with butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Fully functional, we test these with a heat gun, they do open and close. These thermostat control valve assembly mates to the 1967 and 1968 passenger side 390 exhaust manifold up until about Feb 15, 1968. Easy to tell if it is needed with your manifold, no chamfer for the exhaust donuts at collector? you need this or a...

Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black)

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds.