Electrical & Lighting

New 2.5 amp Buss style glass tube fuse for the Mercury Cougar or Ford Mustang. This fuse was used for 1967-68 only and is used for the instrument panel, clock and ashtray lights. This unit measure about 5/8" long and is Sold individually.

Used 3 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for seat belts and door ajar indicators. Blue and red light sockets. These are the same sockets for the seat belt reminder and door ajar warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.

Used 4 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for parking brake and low fuel indicators. Yellow and green light sockets. These are the same sockets for the parking brake and low fuel warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Contains nut, lock washer, and spacer. Fits all Ford alternators.

1968 Mercury Cougar Standard / Ford Mustang 289 / 302 CONCOURS Alternator Harness with Alternator Warning Light - Repro Nice reproduction of the original alternator wiring harness, 3 pin dog bone style connector and wire colors match up to the original Ford drawings. Application is 1968 Mercury Cougar standard models or 1968 Ford Mustang with factory tachometer option, all with 289 or any 302 engines. Ford service number C7ZZ-14305-E, original wire harness marked C8WB-14305-D. *Caution, not...

Nice reproduction of the original alternator wiring harness, 3 pin dog bone style connector and wire colors match up to the original Ford drawings. Application is 1968 Mercury Cougar standard models or 1967 Ford Mustang with factory tachometer option, all with 390-4V/427/428CJ engines. Ford service number C7ZZ-14305-H, original wire harness marked C8ZB-14305-F or C8ZB-14305-B. This harness is designed for the low mount alternator, or cars with thermactor smog. *Excludes X code 390-2V -...

This is a 'made in China' wiring harness. Quality is OK and will work for this application. Application is 1967-68 Mercury Cougar XR7 models and Ford Mustang without factory tachometer option, all with 289 or 302 engines. *Caution, not for use with Cougar standard models or Mustang with alternator warning light. *Note - Excludes California models or cars with factory Thermactor smog pump with low mounted alternators.Replaces Ford Part # C7ZZ-14305-B Door Tag 65B

This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.

Sold individually. Stainless Steel

Reproduction backup light mounting spacers for the Mercury Cougar or Ford Mustang.

Each of these great OEM Style kits include all three required cables, proper terminal and post clamp ends. Unlike CONCOURS CORRECT cables, these do not have the Ford part numbers on them. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) NOTE: These cables are technically correct...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : C8ZZ-14300

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

Perfect fit the first time. You will be happy with this Group 24, quality reproduction and check out the price! These battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Replaces Ford part #: C7ZZ-10732-D.

Good used group 24 tray for 1968-70 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray, for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting).

Concourse Correct with 22 & 24 series batteries for Mustang, Cougar and Shelby GT350/500 made in the USA by Mansfield Mustang to orig. Ford Specs includes attaching bolts Replaces Ford Part # C8ZZ-16060-A

Reproduction Battery Tray Bolts & U Nuts for the 1968 Mercury Cougar / Ford Mustang

Used rear defog blower motor with integral fan. Ford supplied these for many years, some have different connectors on them. Some have the square style as found starting in 1973. We have a good supply of working and tested motors, so request the type of plug end you need.Replaces Ford part number C8AZ-18527-A and D3AZ-18527-A.

Kit comes complete with J bolts and mounting nuts. Replaces Ford Part #: D0AZ-10756-K.

Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.

These courtesy light brackets are located on the very outer right and left under the dash. Typically this bracket is found on the passenger side of 1967-68 Mercury Cougar and Ford Mustang without air conditioning. This is the long style bracket. There is also a short style for both the driver and passenger side courtesy light. If you have factory air conditioning you would want the short bracket that doesn't come into contact with the A/C plenum.Replaces Ford part number C7ZB-13763-A.Fits:1967...

Used windshield wiper mounting bracket for any 1967-68 Mercury Cougar or Ford Mustang. Part of the wiper motor assembly in the Master Parts Catalog, so no Ford number found.

Sold individually these are the very hard to find side marker bulbs for your 1968 Cougar. The 1968 Ford Manuals call for a 97N bulb but that is an error believe it or not... As shown in the NOS light below these bulbs came painted, ALL MODERN REPRODUCTIONS ARE MADE WITH AMBER GLASS (See Amber Glass Listing). The paint is very prone to chipping and after examining several NOS lights that we presume have never been opened we found a couple to have been scratched prior to being installed in the...

Reproduction 631 Glove / Luggage Compartment / Under Dash Courtesy / Trunk Light Bulb for the 1967 - 1973 Mercury Cougar

Bushing that goes to the inside of the brake booster pushrod. This is the early version of this part that is made of plastic, a later version was introduced in 1969 which was made of nylon and is/was more durable.Replaces Ford Part number C9AZ-2474-A

Reproduction bushing for the master cylinder push rod where the switch and brake pedal converge. Two required per car and the bushings are sold separately.Ford part number C5DZ-2B129-B

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Includes battery clamp and bolts required to mount battery on tray. Please note that vinyl coating will almost always crack along edges shortly after installation.

New replacement mounting clip as found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

Used clip found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Prepare to be disappointed... This is a reproduction 1967 - 1968 Ford Mustang clock knob and set screw (replaces Ford part # C7ZZ-15032-A) that can be cut down to work on your 67-68 standard Mercury Cougar (barely). The pictures below will guide you on this "adequate at best" solution for those of you missing this hard to find knob and set screw.Click on images to enlarge. The above picture is a good used original Cougar knob mounted on a 68 clock.  We do not have these original Cougar...

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Used coil mounting bracket. This version of the bracket is probably the most common. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. This version has the notch as shown. We know that this version was used on...

This is a complete set of four used headlight bulbs, marked with the FoMoCo logo. These sets come with two high beam and two low beam bulbs. Each bulb is tested by the electrical department. If you're trying to keep your Cougar or Mustang as close to original as possible, you should definitely grab a set.These bulbs are date coded, so if you want a particular date, be sure to mention it in the comments section of your order.  

Exact reproduction horn ring contact components for the standard horn ring used on two spoke steering wheels, replaces Ford part # C9AZ-13A805-B. Includes new hardware

Horn ring contact components for the standard horn ring found on 68-69 2 spoke steering wheels. Ford part number C9AZ-13A805-B. Not as shiny as the reproduction kit but the price is less and the quality is FoMoCo original all the way. Reference photo above is the order in which the parts are installed.

Reproduction under dash light assembly for the 67 - 68 Cougar or 65 - 68 Mustang. This short style assembly was used on either driver or passenger side. There were two versions of this light, a long bracket version and a short bracket version. The driver side was always the same, but the passenger side typically used the longer version on cars with no A/C. Cars that had air conditioning used the shorter bracket style to keep from coming in contact with the A/C plenum. ...

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

Used service replacement switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and chrome knob, bezel is marked "DEFOG" as shown. *Note - this is not the OEM 1968 defog switch, it is the switch used in defog kits starting in 1970 for many Ford and Mercury dealer installed or over the counter kits.Replaces Ford...

Used switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and black knob marked "DEFOG". Replaces Ford part number C8ZZ-18578-A.