Interior

Used 3 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for seat belts and door ajar indicators. Blue and red light sockets. These are the same sockets for the seat belt reminder and door ajar warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.

Used 4 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for parking brake and low fuel indicators. Yellow and green light sockets. These are the same sockets for the parking brake and low fuel warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.

Reproduction black center A/C vent for the 67 - 68 Mustang.

Reproduction passenger side A/C vent with black camera case finish for the 67 - 68 Mustang. 

Reproduction driver side A/C vent with black camera case finish for the 68 Mustang.

Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests...

Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being blunt about the quality on some of these items, but after using these...

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # C8ZZ-6524100-BK.

Unlike the light blue found on a Cougar this is the darker blue used on the 1968 Mustang. The light blue is not available. This is a good match to the darker blue accents found on the 1968 standard and decor Cougar interior. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being...

Unlike the light blue found on a Cougar this is the darker blue used on the 1968 Mustang. The light blue is not available. This is a good match to the darker blue accents found on the 1968 standard and decor Cougar interior. Color on these is inconsistent and never spot on to the original. No returns on this item.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. Color on these is inconsistent...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue, Parchment, Ivy Gold, Aqua, Saddle, or Nugget Gold. Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests are not correctly colored...

Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being blunt about the quality on some of these items, but after using these...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101. ...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101 Color on these is inconsistent...

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used ashtray for the 1968 Mercury Cougar or Ford Mustang. This unit will come as taken from a Western parts car. Original FoMoCo construction, built to last. There is a slight difference between the 1967 and 1968 dash openings for these ashtrays. This 1968 ashtray painted face, measures 6-13/16 inches long. The 1967 version is 7-1/8 inches long measured with a flexible ruler.Ford part # C8ZB-6504810.

Sold individually # 374212-S

High quality rubber molded around a flexible steel insert. Insert is cadmium plated to prevent rust. A popular replacement item, as they always wear. While this unit also fits the 1965-68 Mustang, it is only correct for the 1968 Cougar XR7-G. Replaces Ford Part #: C5ZZ-7D351 Check out our video on rebuilding your shifter below: ...

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness: 1/4" Replaces Ford Part Numbers: F23Z-3517, C1AA-3517-A, C3AZ-3517-A, C7SZ-3517-D, D0AZ-3517-A, F23Z-3517-B * - may not fit some 67 Mustang applications with a fixed column as these used Ford...

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. Compared to the reproduction version of this bezel, there is a difference. "Emergency Flasher" lettering is much heavier on the originals, plus they came color matched to the steering columns. We can often times supply your desired color, please include color needs in the comments section. Ford part number C9OZ-15C580-A.

Emergency flasher bezel for the side of the tilt steering column. Reproduction bezel in black. Replaces most all tilt swing steering columns from 1967-69. Replaces Ford part number C9AZ-15C80-A, and an earlier part number starting that was likely C7SZ-15C580-A.

Nice reproduction globe box door button bezel for all 1967-70 Mercury Cougar and Ford Mustangs. We do sell used to, see related.Replaces Ford part number C6OB-62060A12.

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

Quality reproduction to replace your pitted original. Replaces Ford Part #: C7ZZ-10852-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Incorrect chrome finish (supposed to be satin not chrome) Mustang part that requires modification to make the metal XR7 insert fit. This is the only new alternative to your broken bezel, we sometimes get in an original that just needs paint. This unit will also fit the Cyclone, Montego, and many other Mercurys and Fords. Replaces Ford part # C8ZZ-3D572-A.

Inexpensive upgrade, replaces that bezel damaged by improper screw driver removal. We also sell the special tool that removes this without hassle or damage

Used ignition lock cylinder bezel for any 1967-68 Mercury Cougar, ford Mustang and likely Fairlane / Comet. Good used condition, we recycle the pitted crusty ones. Half the price of the repop version. We also sell the special tool that removes this without hassle or damage.Replaces Ford part number C6OZ-11584-A.

This radio bezel is made by the original Ford supplier and features high quality die cast chrome. For cars without a center console. Replaces Ford Part #:C8ZA-18842-C.

Both our A and B quality bezels will need a replacement brushed aluminum overlay. This used bezel will have no broken or missing parts. Most likely the white will be missing from the P R N D 2 1. We also have grade "B" used units with minor flaws for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand...

Both our A and B quality bezels will need the overlay replaced. Cosmetically this bezel will be as good as our grade "A" units, but when you turn them over you will notice one or two of the feet will be broken off. These missing feet may make it a little more cumbersome to install and if someone walks on your installed console these feet do provide support. Obviously it would be easy to glue on some feet (or spacers) but this item will install just fine without them. Most likely the white will...

This shift indicator will work on a 1967 or 1968 Cougar or Mustang equipped with automatic transmission. It comes with all items shown here.

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used to mount the vacuum actuator to the column in 1967 and the actuator to the bracket on 68-69. Also used to mount the steering column relay and vacuum release valve in 1968-69.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last...

Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a D with triangles, some with E and three triangles and others had no stamping at all. 13/16" hex head, two inch bolt with a 7/8 inch shoulder. 

Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Strong "A" on this one as shown. There is another version of this same bolt with a light "A" or smooth head and no markings. See related items.

Used to mount the front retractor to the inner rocker panel. Used in conjunction with a large washer. 13/16" hex head, 1-1/2inch bolt with a 1/2 inch long shoulder. May or may not be marked with a letter "C".

Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a F and others had no stamping at all. 13/16" hex head, 1-7/16 inch bolt with a 1/4 inch shoulder. 

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Fits 1967 - 1973 Standard or XR7

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.