Interior

This hard plastic part slips over your floor shifter stem and keeps coins and such from falling inside your center console. Replaces Ford part number C7ZZ-7C445-A. Check out our video on rebuilding your shifter below: ...

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

Good used light used only on the 1967 automatic consoles. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...). If you choose to run the light without the diffuser it will shine bright as opposed to a warm glow.  Ford Part Number: C7ZZ-15A808B Fits 67 CougarFits 67 Mustang Check out our video on rebuilding...

For use with factory and reproduction console parts on a 1968 Mercury Cougar or Ford Mustang. Plugs into your existing console wiring harness. Double male plug is 1968 only. Sold without light bulb. The supplier says this replaces Ford part number C7ZZ-15A808-B but that is incorrect as the Ford part number for 68 is C8ZZ-15A808-B. To use this on a 67 the plug would have to be changed to a male / female combo plug.

Reproduction shift indicator light for use on the 68 Cougar and Mustang without a center console. Plugs into your existing console wiring harness. Double male plug is 1968 only. 

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.

Better quality than our reproduction for less money. Ford part number C0DZ-13807-A.

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Easy to replace, keeps correct tension on your gas pedal.

Used spring cap that is used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...

Don't try to straighten your rod if it looks like this. The contour seen here is correct. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

These will always have some amount of minor pitting. Not for use on XR7 or manual transmission consoles.Casting number as seen on the bottom side C8ZB-65045B72-BW.

Grade "B"s  will show obvious pitting, but will have no cracks. Not for use on XR7 or manual transmission consoles.Casting number as seen on the bottom side C8ZB-65045B72-BW.

Fits 1968 Standard or XR7

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 

Fixed steering column from a 1968 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often breake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, and wire keeper (wiring cover...

Good used standard steering wheel from a 1968 base model Standard Cougar, or Mustang or nearly any Ford. This is not the deluxe steering wheel with simulated wood grain. Solid color only. Plan on respraying the color for a fresh look. We normally have black in stock, other colors sometimes available. Usually these will have minor cracks at 12 and 6 O'clock. There is also a very good reproduction available, please see related items. Check out this video ...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Note that the color on these has too much gray in it and is...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Check out this video ...

Pictured in black. This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Check out this video ...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

Cracked wheel good for restoration. Usually cracked at 12 and 6 as well as on the two spokes. Check out this video

This is a restored 1968 steering wheel that is correct for all but the later production, standard interior equipped 1968 Cougars. Only the XR7 & XR7G received the woodgrain center section, the decor and standard interior equipped Cougars received a color coded to the wheel vinyl insert. All 1968 Cougars used this center emblem except the XR7G which used a larger metal version. This wheel does not include the center pad assembly or horn ring (shown for display purposes only). As we prefer to...

Good used wheel with no cracks but will show wear on the woodgrained fascia. We usually have several wheels for $20-$100 more and $20-$100 less than the wheel pictured here. Most are black in color but we do have a few colored wheels. Call for the many details and options. Check out this video

B grade pad has shrunk to the point that the center section will not fit well and you may have to file some of the plastic away for a proper fit, it will be curling a little at the top where it meets the wheel and overall will be rather hard from UV exposure. Additionally, it may show some signs of wear to the texture of the graining. If you state your preference in the comments section we will try to accommodate you on color.

Reproduction Two Spoke Steering Wheel Pad for the 1968 Mercury Cougar Check out our video review

This is the 1968 Cougar visor bracket. Not an exact match for 1971 - 1973, but will work. The hole spacing and distance from the windshield is identical to that on the 71-73, the bracket is just 1/8" longer on the side that actually holds the visor tip. This unit is only available in black or neutral. We have most other unfaded colors in used. This item works for 68 Cougar Coupe, 68 Mustang Coupe / Convertible and 71-73 Cougar Convertibles. Replaces Ford Part # C8ZZ-6204132, C8ZZ-17690 OR...

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

For the purists out there we have a very limited amount of used moon crater visors that have no impressions, seam separation and minimal rust on the clips if any.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually.

Reproduction Moon Crater Sun Visor for the 1967 and 1968 Mercury Cougar / Ford Mustang. Visors are fully padded and covered with the correct textured moon skin to match the headliner. Sold as a Pair. Nugget Gold is not available in Moon Skin Crater, it is only available in a smooth vinyl.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang, and most 1965-69 Ford and Mercury full sized cars such as Galaxie, Monterey, Parklane, Montclair, etc.Fits 67 CougarFits 68 CougarFits 65 Mustang Fits 66 MustangFits 67 MustangFits 68 Mustang

Replacement turnsignal switch for all 1968 Mercury Cougar and Ford Mustang with fixed (non-tilt) steering columns. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. For 1968, the relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. We also have a handmade version of this same tool for a lower price.

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...