Steering

part # 370608-S. Used in multiple places on mounting brackets.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

Sleeve and hardware for joining the inner and outer tie rods together. This also is a 'toe in' adjustment part. Sold individually, two needed per car. Replaces Ford Part #: C2AA-3310-A

Reservoir Attaching Nut 351335-S38 - Used Nuts for attaching the oil reservoir to the pump. The larger of the two nuts goes against the can. Threads of 5/8"-18 to fit the high pressure port. This is a pair of nuts, one tall and one short. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, except for 1970 with 351 engine, and Mustang with 302 engines. 1970 302 / 351 engines used a different pump with an offset...

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. There is a slight difference between the original bezel and these reproductions. Original bezels have taller "Emergency Flasher" lettering, plus they came color matched to the steering columns. Functional reproduction item. Ford part number C9OZ-15C580-A.

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. Compared to the reproduction version of this bezel, there is a difference. "Emergency Flasher" lettering is much heavier on the originals, plus they came color matched to the steering columns. We can often times supply your desired color, please include color needs in the comments section. Ford part number C9OZ-15C580-A.

Emergency flasher bezel for the side of the tilt steering column. Reproduction bezel in black. Replaces most all tilt swing steering columns from 1967-69. Replaces Ford part number C9AZ-15C80-A, and an earlier part number starting that was likely C7SZ-15C580-A.

Incorrect chrome finish (supposed to be satin not chrome) Mustang part that requires modification to make the metal XR7 insert fit. This is the only new alternative to your broken bezel, we sometimes get in an original that just needs paint. This unit will also fit the Cyclone, Montego, and many other Mercurys and Fords. Replaces Ford part # C8ZZ-3D572-A.

Replaces Ford Part # 43260-S Sold individually

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Replaces Ford part #375381-S Phosphate & Oil Finish

Used front crossmember bolt for the Mercury Cougar or Ford Mustang. It is crucial that you use this correct tapered bolt when installing the front cross member.

Reproduction zinc front shock bolt with correct anchor symbol on the head, just like the originals.Sold individually.

Front U clamp sway bar bracket bolt, for any 1967-68 Mercury Cougar or Ford Mustang. 3/8-16 x 1.0 Grade 5 bolt. Sold individually, 4 per car. part #20408-S

1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish.  Ford Part # 382486-S.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used to mount the vacuum actuator to the column in 1967 and the actuator to the bracket on 68-69. Also used to mount the steering column relay and vacuum release valve in 1968-69.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last...

Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block.  Also used on the 1970 Mercury Cougar with 428CJ. Phosphate & Oil (gray-black)

replaces Ford part # B-12764

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Replaces Ford part # 45964-S Sold individually

Reproduction steering gear box bolt. Sold individually

Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually

Reproduction Upper Control Arm To Shock Tower bolt.  Sold individually. Replaces Ford part # 38049-S

Bolt kit for mounting power steering ram cylinder brackets to the frame rail on any 1967-70 Mercury Cougar or Ford Mustang. Kit includes: two short bolts with lock washers, long horizontal bolt, nut, and reinforcing washer. Quality AMK fastener kit.

Reproduction rubber boot for the drag link end of the power steering ram cylinder on most any 1967-70 Ford small and intermediate sized cars. Comes with band style crimp clamp like the originals. Keep in mind that this product is made from material that is thinner and softer than OEM.

Reproduction power steering control valve boot and clamp, for the 1967-70 Mercury Cougar or 1965-70 Ford Mustang. Gold tone clamp, molded rubber boot, and pair of screws. Very accurate reproduction. 

One year only bracket used on both fixed and tilt column cars.

Bare metal power steering hose bracket for any 1967-69 small block Mercury Cougar or Ford Mustang. 289-2V, 289-4V, 302-2V, 302-4V, 351-2V, and 351-4V. No rubber insulator included.

For any 1967 or 1968 Cougar with either a 289 or 302 engine. Virtually the same bracket as for the 1969 351W engine. Except for the obvious 1-1/4 inch hole in the middle of the bracket, they are the same. Compare the OEM used part price to the reproduction part. Ford master part number C7AZ-3C511-A, same part number as the 351W bracket with the addition of the large hole. Ford intended to have a casting number stamped on these brackets and it would have been C7AA-3C511-B. For restoration...

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.

This cast bracket bolts to the frame on the driver side and anchors the power steering hydraulic cylinder. One of the benefits of buying parts from Western parts cars is that they have not been corroded by salt! This part comes "as taken from a parts car". At least two variations of this bracket (see photos above) between 1967-70. Our observations show the version with the curved casting number version orientation to be from 1970 Cougars with were all built in Dearborn, Michigan. The...

Lower steering column mounting bracket. 1967-68 Mercury Cougar and Ford Mustang. Right and left halves with original fasteners. Rubber gasket sold separately.Ford part number C7ZZ-65017A50 and C7ZZ-65017A51.

This used upper column bracket bolts to the brake pedestal bracket under your dash. The two threaded studs face downward and are used to attach the lower column bracket.

Used tilt column vacuum can bracket for the 1968 Mercury Cougar *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used original lower power steering hose mounting bracket for 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. This used version has the indexing tab which the reproduction does not. May come with new bolt and or rubber insulator.Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.

Replaces Ford Part # 382713-S Sold individually

Sold as a Pair. Ford Part #: C8AZ-2B296-A

part# 384114-S100 Sold individually

Replaces Ford Part # C8AZ-2069-A Sold individually

These are OEM replacement bushings. The problem with these are most original sets are rusted out on the metal parts. We highly recommend the upgrade, unitized sets we sell over the orignal design.Replaces Ford Part #: C6OZ-3A187-A

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair.Replaces Ford part # C8AZ-2B299-A.

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...