All Products

Used on both 351w 2V and 4V FMX transmissions in 1969. Approximately 17-1/2" long with a black color code paint daub on the end closest to the carburetor. This is not correct for any 1970 Cougar equipped with a 351 Cleveland or Windsor motor. *NOTE* Although the MPC lists this part as 1969 only it does in fact apply to the 1970 Cougars equipped with the 351 Windsor two barrel motor. Not only did Ford confuse the public by giving both the 1970 351C 2V and 351W 2V the same engine code "H" in...

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...

Black ABS plastic replacement kick panels without speaker pods. Sold as a pair. Reproduction kick panels made for 1971-73 Ford Mustang, but will fit a 1971-73 Mercury Cougar OK.

These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common after-market speakers in multiple depths. For more discussion on kick panel speaker options, check out this thread. If you only are looking to buy one, please call, we often times have an odd number in...

These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common aftermarket 5-1/4" speakers in multiple depths. Sold as a pair. For more discussion on kick panel speaker options, check out this thread. Replaces Ford Part number C8OA-19A067-A ...

Reproduction kick panel insulation for the 1967 - 1968 Mercury Cougar or Ford Mustang 

Exact reproduction made by Daniel Carpenter. Injection molded black plastic. Very nice. Much thicker and more durable than other reproductions. Sold as a pair. Replaces Ford Part # : C9ZZ-6502344/5

Kick panels for the 1967 and 1968 Mercury Cougar that include 6 1/2" coaxial (2 way) 100 watt speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. For some discussion on kick panel speaker options, check out this thread.

Great way to update your sound system without cutting door panels or other original parts. Great fit and finish, easy installation. Pioneer speakers are 4ohms, 6 1/2" coaxial (2 way) 160 watts per speaker, for a total of 320 watts max output! Only available in black, but can be painted to match your interior with flexible paint. For more discussion on kick panel speaker options, check out this thread.

Kick panels for the 1967 and 1968 Mercury Cougar that are formed to accommodate speakers. Speakers are not included. These are designed for those who would like to choose their own speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. These now come pre-cut for a 5 1/4 inch speaker. For more discussion on kick panel speaker options, check out this thread.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.*NOTE* These units may require some slight modification to fit perfectly in your unique Cat or Pony.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.

Knee pad as found on select 1968 Mercury Cougars. This grade A version will not be separating from the metal strip. Not a common option, your Cougar would have a line of mounting holes across the lower dash and above the glove box if your Cougar originally came with a knee pad. We don't always have these in stock in this condition. Call for desired color, but plan on spraying with a quality vinyl dye for best results. Black is our most popular requested color, and we will probably always be...

Knee pad as found on select 1968 Mercury Cougars. This grade B version will be separating from the metal strip, and or may have warpage. Not a common option, your Cougar would have a line of mounting holes across the lower dash and above the glove box if your Cougar originally came with a knee pad. We always have these in stock in this condition. Call for desired color, but plan on spraying with a quality vinyl dye for best results. This pad is different from the Mustang version which is...

Reproduction cigar / cigarette lighter for the 71 - 73 Cougar.

Used convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Used and tested convertible top switch, it will not come with a knob. This switch was also used on Cougars with factory power sunroofs. *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash.

Knob for engaging the emergency flasher switch on a fixed (non-tilt) steering column. This original knob is plastic, the reproductions are chrome plated die cast.

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Used emergency flasher knob for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These knobs are very fragile and the chrome plating will show some minor scratches and pitting. We try and keep these on hand, but the fragility makes them 'subject to availability'. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down...

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand.Here is a helpful youtube video on how to go about removing a headlight...

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand. NOTE - This does not fit Mustang headlight switches  Here is a helpful...

Headlight switch knob for any 1967 Mercury Cougar or Ford Mustang. Not the same as 1968. This is a nice detail item for concours judged cars. There is a difference between 1967 and 1968 knobs as shown in the photos. Nice used condition.  Original Ford part number C7ZZ-11661-A.

Headlight switch knob for any 1968 Mercury Cougar or Ford Mustang. Not the same as 1967, which is reproduced by Scott Drake. This is a nice detail item for concours judged cars. There is a difference between 1967 and 1968 knobs as shown in the photos. Nice used condition. Original Ford part number C8ZZ-11661-A.

Good used headlight switch knob for any 1969-70 Mercury Cougar or Ford Mustang. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand. Ford part number C9ZZ-11661-A Here is a helpful youtube video on how to go about removing a...

Reproduction headlight switch knob for the 71 - 73 Cougar.

Not for use on cars with A/C. Keep in mind we also have excellent used knobs sold individually or as a set.

Don't be fooled by knobs with similar part numbers, they have longer shafts and will not work as well on your Mercury Cougar or Ford Mustang application.Ford part # D1ZZ-18830-A, and Ford casting # D1ZA-18A932-AA.*TRIVIA* Did you know that Ford called the inner (balance / tone) radio knobs "discs?"

This is one of the easier knobs to find in that it does not break easily and can be found on many 1967 FoMoCo products. Not used on Cougars with a center console and little to no differences can be seen between the different examples. One explanation for having multiple casting numbers for the same part is that Ford would use multiple suppliers for a single part. To differentiate which part came from which vendor, different casting numbers would be assigned. If there was a problem with a run...

Reproduction inner radio knob used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

Rare plastic radio knob used only with the 1967 XR7 and standard Cougar console. This knob differs from the Mustang console and Cougar / Mustang non console knob in that it is deeper to clear the console pad unique to the 1967 Cougar. Ford called these rare little units "discs" back in the day Replaces part # C7WA-18A932-A

Used on early non console 1967 models and has a lower profile than the later version. We also have pitted knobs we can throw in on a order for free, just mention it if all you need is a knob that gets the job done.Ford part # C7MA-18817-A.

Unlike the plastic console knobs, the issue with these metal knobs is pitting as opposed to breaking. Very hard to find in clean condition.Replaces part # C7ZA-18817

This knob is for Cougars equipped with consoles only and then only the earliest of Cougars would have seen this plastic, lower profile, delicate knob. Very hard to find Cougar only knob that is not found on any other model. This is one RARE little dude indeed!Replaces part # C7WA-18817

Reproduction radio knob used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits: 1968 Mercury Cougar

Rare radio knob used only on the 1967 XR7 and standard Cougar console. This knob differs from the Mustang console and Cougar / Mustang non console knob in that it is deeper to clear the console pad that is unique to the 1967 Mercury Cougar. Early standard model Cougars with the console used a more petite version of this plastic knob. Replaces part # C7WA-18817-B

Used wiper knob for any 1967 Mercury Cougar. This version is smaller than the 1968 knob. Unlike the 1968 version, there is no set screw, and is simply pressed into place. You may need to use a bit of adhesive to hold in place. Good condition, will have a small rust pit or two.

Used wiper knob for any 1968 Mercury Cougar. This detachable knob with set screw is slightly larger than the ones found in 1967. Good condition, will have a small rust pit or two.

Used knob for wiper control switch on dash panel. Constructed of metal with chrome, may show some wear on the black painted section and flaws in the plating.Ford part number C9ZZ-17513-C.

Chrome and black knob just like the original.NOTE: This knob is correct for 1969. It will fit on a 1970, however the orientation of the pointer will be off. You can find a good used 70 knob here. Replaces Ford Part # : C9ZZ-17513

1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.

This knob set differs from the set used later in 1967 only in that the outer knob has a lower profile head. Keep in mind we have reproduction knobs that will work in place of these.

This set of reproduction used knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear...

Full set of metal radio knobs for the 1967 Mustang or Cougar. Not for use with the 1967 Cougars equipped with factory center console. Keep in mind we have reproduction knobs that will work in place of these.

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

The early Cougars had a lower profile head on the outer knob. It is assumed they beefed up the design in early in the year because the knobs were easily broken. These delicate plastic knobs are very hard to find in this condition. Only the utmost purist would care to obtain a trivial detail part such as these to make their car correct. These deeper knobs were only used in cars equipped with a factory center console. The Mustangs did not have a padded console in 1967 so this set is for 1967...

Complete five piece set for 1967 Cougars with center console. The majority of 1967 model Cougars got this improved design with stronger outer knobs. Keep in mind we have reproduction knobs that will work in place of these. Also keep in mind we will accept your incomplete set of used 67 console radio knobs for a complete set of our 1968 reproduction knobs. Give us a ring for details.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.