All Products

Rubberized bumper filler combination stone deflector, that mounts on the driver side fender on a 1973 Cougar. This unit is also known as a bumper filler, rock guard, or filler panel. Grade A used condition, may have a defect that can't be seen when installed.Replaces Ford part number D3WY-17779-B.

Very good used 1970 Cougar or Mustang console storage compartment. Sometimes called a 'well'. This is the "before 12/1/69" version, without cigar lighter and button or latch. According to the MPC there were three versions: prior to 9/2/69, 9/2/69 to 12/1/69, and after 12/1/69. These originally came in 6 different colors - black blue red ginger green tobacco. Notice that this part does not have the cigar lighter? In 1970 the cigar lighter was moved to the dash. Ford stuck the cigar lighter into...

Very good used 1970 Cougar or Mustang console storage compartment. Sometimes called a 'well'. According to the MPC there were three versions: prior to 9/2/69, 9/2/69 to 12/1/69, and after 12/1/69. These originally came in 6 different colors - black blue red ginger green tobacco. Notice that this part does not have the cigar lighter? In 1970 the cigar lighter was moved to the dash. Ford stuck the cigar lighter into the position previously occupied by the ignition switch in 1969...

Nice used driver side strut rod that fits all 1968-69 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1968-69 Torino, Cyclone, Ranchero. 1968-69 strut rods are the same as 1970-73 strut rods, but 1968-69 rods have stepped down threads at the end. Ford part number C8OZ-3468-B. Sold as a bare strut rod, we also offer the used hardware for installation...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a better value than the Chinese rods we sell.*Note - 1970-73 strut rods work equally well.

Used 14x6" styled steel wheel for your Mercury Cougar. This unit has a total width 7", a 4" backspacing, and a 1- 13/16" center hole. This is the service replacement number and it will fit all 1967 and newer Cougars with or without disc brakes. Slightly wider than the 1967 counterpart. Shipped bare without center cap or trim ring. We have these wheels in various conditions with minor blemishes and they are subject to availability.Ford part # C8WY-1007-A.

Used 14x6" styled steel wheel for your Mercury Cougar. This unit has a backspacing of 4" and a total width of 7". Shipped bare without center cap or trim ring, but does include the five stainless steel window trim parts. Various conditions and all will need to be repainted. Used 'as is', wheel as found in the wilds of our wrecking yard and are subject to availability.Ford part # C9WY-1007-B. *NOTE* 1969 Eliminators did not offer this as an upgrade wheel but this was the upgrade wheel for the...

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 14x7" styled steel wheel with a chrome outer rim and an original argent finish between the chrome spokes on the center. No, Mercury never offered them in a...

Reproduction 15x6" styled steel wheel for your Mercury Cougar. This unit comes with 4.5" back-space, unless ordered otherwise. Hub caps and lug nuts are sold separately. NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal with classics and do not have the right attachment. If you attempt to balance these wheels without the correct adapter they will resemble a bent...

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. No, Mercury never offered wheels in a 15x7" for an early Cougar... We now sell more of these custom made SS wheels than the original 14x6" version. Not only do they look...

Used 'Kelsey Hayes' 15x7" styled steel wheel with a new chrome 15" rim for your Mercury Cougar. These originally came 14x7" on the Cougar with a beauty ring. We take your original wheels and have a new 15x7" outer chrome rim installed. This purchase requires a core wheel be sent to us. The good news is that you can find these in 14x6" or 14x7" inexpensively when they have been damaged and rusted on the outer lip. As long as the centers are untouched they are good cores. We sell these...

Used driver side (left hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind you...

Used passenger side (right hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind...

D3ZZ-6501508-B This is the correct hanger for after 6-25-1972 Mercury Cougar or Ford Mustang and 1973 cars, with power disc front brakes, and with manual transmissions. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number D3ZZ-6501508-B for power disc front brakes.

The Competition Handling Package was available optionally on any 1971- 1973 Cougar. However, it was standard on both 429CJ engines (J code non-ram air and C code ram air engines) and all 1972 and 1973 351CJ's (Q code engine). You would paint your sway bar chassis black and add 2 Yellow and 1 Green stripes to replicate the factory markings. This is factory used front sway bar, does not include any mounting brackets or end link kits.Ford part # D1ZZ-5482-D.Here's our little film to help you...

C7ZZ-5482-B This is a factory used front sway bar. This is the same size 3/4 inch diameter as the 289 and 302 sway bar but has a slight difference in the bends for the 1967 390-4V or 6.5Liter engines. This bar was factory identified with a One-Yellow and One-Blue paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

Used factory 3/4 inch sway bar for the FE 390 engine of 1969. This bar was factory identified with a single 'Yellow' and a single 'Blue' paint stripe. This bar is not to be confused with the Competition Handling Package sway bar which was optional on any 1969 Cougar. This factory used front sway bar does not include any mounting brackets or end link kits. Ford part # C9ZZ-5482-C.

For any 1970 Cougar, part of the Competition Handling Package. Rear sway bars were standard fare on all Boss 302 Eliminators, and 428 Cobra Jets. This bar is 1/2 inches thick. Concours restorers, paint this bar chassis black and put a single Pink stripe on it. This factory used rear sway bar, does not include any mounting brackets or end link kits.Replaces Ford part number D0WY-5A772-A.*Note - will not fit Mustangs.Here's our little film to help you fortify your flexxy feline! ...

Here is our NOS vacuum valve assembly which is fairly hard to come by these days. This unit is for Mercury Cougars or Ford Mustangs with integral or factory air conditioning. This part is good until an assembly date of 1/3/1972 and, if you want, we also have good used pieces in stock for your Coug or Stang as well. Ford part # C9ZZ-19B888-A.

NOS Back up light switch for the 1967 Cougar or Mustang. Ford Part # : C7ZZ-15520-A

NOS brake warning light switch for the Mercury Cougar or Ford Mustang that is identified by the single pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder, this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Ford part # C7AZ-2B264-A.

NOS, never been installed part they may or may not come with original box, will show shelf wear. Ford Engineering number stamped on the part is C8WB-11652-C.

May or may not come with original box, guaranteed to be never installed NOS. Ford engineering number stamped on part is C9WY-11652-B

Brand new in the Motorcraft box original FoMoCo part. Engineering number stamped in the part is D0WB-11652-B

This used intermittent wiper switch has a two speed wiper function, but when turned counter clockwise, it has a rheostat that sets the different delay times. Switches can be physically marked with casting numbers of C9ZB-17A553-E, C9ZF-17A553-B or C9ZF-17A553-C. Any of which can be correct, and chances are, there are probably other casting numbers out there as well. This 69 switch has a total length of 3 3/8". A 1970 switch can be used, but the shaft is about 3/8" longer. Sometimes this...

Tested and inspected neutral safety switch for the C-6 transmission installed in 1970 - early1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971.Look for a transmission code of U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: D1ZP-7A247-AA, or D0ZZ-7A247-B, SW 920.

C8AZ-14529-C

NOS fixed column turn signal switch for the 1967 Mercury Cougar or Ford Mustang. This is a later service replacement turn signal switch, it may have an extra wire or two, and the wire lengths may be longer than the factory original. Ford part number C7ZZ-13341-F Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....

NOS fixed column turn signal switch for the Mercury Cougar or Ford Mustang.Ford part # C9AZ-13341-R.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

NOS fixed column turn signal switch for the 1970 - 1972 Mercury Cougar or Ford Mustang.Ford part number D2AZ-13341-CNeed help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used Turn Signal Switch / Fixed Column for the 1969 Mercury Cougar / 1969 Ford Mustang 

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

NOS switch and bracket for the emergency / parking brake. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13441-AA ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13441-AA

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13440-AA ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13440-AA

This oddball sequential unit was only used from 2/1/1971 to 5/15/1971 and will be of no interest except for to select few. The differentiating factor is the hard plastic connectors. We can supply a reproduction of this unit but it requires that you send your old unit to to us so we can reuse the plugs. Ford part # D1WY-13A366-C. 1971 Cougars built from 2/1/71 to 5/15/71 used a unique sequential system in the trunk, D1WY-13A366-C. It uses two connectors, grey and light blue, that are no longer...

This grade "B" taillight harness will have one or two professional repairs with unmelted plug ends. This unit is for Mercury Cougars built prior to 1-3-67 with the stop lamp relay positioned next to the sequential unit in the trunk as opposed to under dash found on models made after 1-2-67. XR7 and Standard Cougars use the same rear wiring harness to the taillights. *NOTE* The stand out identifier of the early vs. late rear harness is the flat four prong plug with a red, two green and one...

This grade "B" taillight wiring harness is a good used harness that may have one or two professional repairs and the plug ends will be nice and unmelted. Not for use with XR7 or Eliminator. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is...

Used grade "B" used harness that may have one or two professional repairs. Correct for XR7, Eliminator, and 1969-70 Shelby Mustang GT-350 and GT-500. Ford part # C9WY-14405-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information...

Used grade "B" taillight wiring harness for the Mercury Cougar XR7. This unit may have one or two professional repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Cable length 23.75 inches long. *Note - Used on 429 Cobra Jet Cougars before 4/1/1971.

Cable length 23.75 inches long. *Note - Used on 429 Cobra Jet Cougars after 4/1/1971.

Used throttle cable for all 1969 Mercury Cougar and Ford Mustang with V-8 engines.Very hard to find one year only cable with no cracks. We rarely have this one in stock.

NOS throttle cable for 1969 Mercury Cougar or Ford Mustang V-8. Version with the plastic tab for mounting to fire wall.Replaces Ford part #: C9ZZ-9A758-A.

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...