All Products

Single cylinder head from 1968 Mercury Cougar 302-4V engines without smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 52-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C8OE-D and "302" and "4-V".Current casting dates include: 7G25,...

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...

Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....

Used highly collectible Dan Gurney slot car racing track made by the Republic Tool and Manufacturing Corporation in Los Angeles California. Open box and lightly used. Both cars are intact, and the decals have been placed on the the vehicles and the track. Everything is good condition, but the cars have not been tested and the red car has had it's wheels painted. Other than that, this is a rare and truly great find. Features the Mercury Cougar Logo on front of the box.

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider installing your dash...

Used aluminum face pad moulding / trim four piece set for the Mercury Cougar.

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent as shown here. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider...

Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "A" grade used is one without cracks or chips. Put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'.  Current color appears to be Aqua Blue. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Complete very nice grade A bezel for the standard or decor level interior for both the 1970 and 1969 Mercury Cougar. Includes a metal "COUGAR" emblem. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you...

Complete very nice bezel for the Standard or Decor level interior for both the 1970 and 1969 Mercury Cougar. Includes a plastic "COUGAR" emblem.

Grade "A" panel with no blemishes, ready to install on your show car. This listing does not include emblem or the aluminum surround.

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check out our video on dash removal and restoration: ...

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. The best way to judge just how much fading has occurred on the panel is to remove the emblem for comparison purposes. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side.Check...

This actually is a pretty impressive part once installed if your expectations are not overly high. It fits snug (very tight) over your existing cracked dash and you affix it by putting silicone around the perimeter. Once in place the obvious indicators of it not being original are the lack of simulated stitching on the leading edge and the larger perforations for the center speaker. The good thing about this unit is that your dash pad can have large chunks missing and it still will work! You...

This actually is a pretty impressive part once installed. It fits snug (very tight) over your existing cracked dash and you affix it by putting silicone around the perimeter. Unlike the 67-70 there is no stitched edge or speaker holes in the 71-3 so it is a perfect candidate for this cover. The good thing about this unit is that your dash pad can have large chunks missing and it still will work! You can install this without removing the dash and it is very hard to detect once in place. Made of...

Of the three covers used on the 67-73 Cougars we find this one the most difficult to use. Will Not Work On Badly Distorted Dash Pads. The problem is not with the product but rather the design of the original dash pad. Unlike the 69-73 pads the 67-68 pads are prone to warping (sagging) badly. Since this glue on shell is rather rigid you have to have a mostly straight pad to work with. Large cracks are no problem even if your pad is curling at the cracks, just break off the portions of your...

This used part comes carefully cut from a parts car and will include all mounting tabs. It is slightly different from the Mustang version as it has a different contour where the dash pad attaches. AC and no AC are the same, but 67 and 68 differ slightly in height of the area where the ashtray is installed.  

This used part comes carefully cut from a parts car and will include all mounting tabs. It is slightly different from the Mustang version as it has a different contour where the dash pad attaches. AC and no AC are the same, but 67 and 68 differ slightly in height of the area where the ashtray is installed.  

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used some pitting and or  extra holes. Replaces Ford part number C9ZZ-6504320-D.

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used, may have...

Used steel lower dash panel for all 1970 Mercury Cougar and Ford Mustang without factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. Grade B used = some pitting and or extra holes. Replaces Ford part number D0ZZ-6504320.

Reproduction heater dash plate for the 67 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).Replaces Ford part number C7ZZ-18A651-B

Reproduction heater dash plate for the 68 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).

Quality Kenwood speakers that features two 40 watt 3 1/2" coaxial two way speakers. this unit is a huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with in-dash factory AC or not. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

Used switch for the rear defog or defogger fan on any 1970 Mercury Cougar XR7. Rocker switch only. Tested and working two speed switch. Replaces Ford part number D0WY-18578-A.*Note - 1970 Standard Model Cougar uses the 1969 Mercury Cougar switch over the radio.

Used service replacement switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and chrome knob, bezel is marked "DEFOG" as shown. *Note - this is not the OEM 1968 defog switch, it is the switch used in defog kits starting in 1970 for many Ford and Mercury dealer installed or over the counter kits.Replaces Ford...

Used switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and black knob marked "DEFOG". Replaces Ford part number C8ZZ-18578-A.

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing, good chrome on the male buckle and it may even have the date code tag still in place. We will try to obtain the correct date code if...

Also called a pumpkin, 2.75:1 open ratio. Check your door tag under "Axle". 1968 code 1 1969-73 code 2

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - Used Also called a pumpkin, 3.00:1 open ratio. These 3rd members will have the fill plug. Check your door tag under "Axle".

Also called a pumpkin, 2.79:1 open ratio. Check your door tag under "Axle". 1967 code 0 (zero) 1968 code 2

Also called a pumpkin, 3.00:1 open ratio. 1967 9 inch third members did not originally come with fill plugs. The back of the housing had the oil fill plug. You can mix and match 9 inch assemblies from 1967-1970, just make sure that you have at least one fill plug. Check your door tag under "Axle". 1967 code 1

NOS Dinky Toys 1968 Mercury Cougar. Still in the box and in perfect condition. High quality production made by the Meccano factory in Liverpool, England, these toy are the real deal and not cheap plastic.   Features: Retractable antennaReal rubber tiresOpening doorsTilting front seatsSuspension

STOPFLEX incorporates a special 4 layer design for superior strength and virtually no volumetric expansion. It starts with a Teflon PTFE core (liner) which is wrapped first in a Kevlar braid, followed by an elastomer barrier and then it's strengthened further by the outer stainless steel braid. Replacing original equipment rubber hoses with STOPFLEX?? stainless steel braided hoses will increase braking performance by doing away with the soft spongy brake pedal. Rubber hoses expand, with the...

Reproduction front to rear axle stainless steel brake line kit for Mercury Cougars produced before Feb. 1967.Early production brake lines were routed 'over' the steering column. This intermediate style Stainless Steel line attaches to the transmission tunnel and connects the brass distribution block in the front to the flexible brake hose at the rear of the car. This version is for 1967 Mercury Cougars with rear mounted proportioning valves. Application does not change if the front is drum or...

Excellent quality replacements. Includes hub, studs, and bearing races. Single piece design. Rotors Are Precision Machined For Smooth Brake Operation.; Qc100 Venting Matches The O.E. Cooling Vanes To Manage Brake Temperature, Prevent Noise & Limit Vibration.  .81" thickness of Rotor brake surface. 

Excellent USA made quality replacement disc brake rotor. One piece rotor with wheel studs as shown, also includes installed bearing race. Replaces Ford Part #: C5ZZ-1102-B.

New high quality factory replacement rotors for early Mustang and 1967 Cougar 4 piston cars. Also a replacement for many aftermarket Ford disc brake conversions. These drilled and slotted brake rotors come ready to install on your vehicle with bearing races installed from the factory. Sold as a pair only as they are directional / side specific. For use with stock calipers. Precision drill pattern vents away heated gasses caused by braking, allowing for more contact between pad and rotor....

Reproduction disc brake distribution block for Mercury Cougar or Ford Mustang with factory installed disc brakes. Mounts to the driver side fender apron with a single bolt. Bare block without single pin brake switch.  Replaces Ford part # C7ZZ-2B257-D. Check out this video

Used disc brake distribution block for Mercury Cougar or Ford Mustang with factory installed disc brakes. Mounts to the driver side fender apron with a single bolt. Bare block without single pin brake switch. See also our rebuild kit that includes all the seals for the distribution block and proportioning valve. Plan on testing and or rebuilding before installation. Rebuild kits available. Ford part # C7ZZ-2B257-D. Check out this video ...

D0OZ-2B257-C Disc brake distribution block for 1970 through 1973 Cougar and Mustang with factory disc brakes. Mounts to the driver side fender apron with two nuts. Bare block without brake switch. Will need a rebuild kit installed prior to using. Ford casting number D0OA-2B328-D *NOTE* Starting in 1970 there was a built in proportioning valve. **NOTE** Sometime during the 1972 model year there was a change to a D2ZA-2B328-AA casting number distribution block. Check out this video ...

D2ZA-2B328-AA Disc brake distribution block for 1970 through 1973 Cougar and Mustang with factory disc brakes. Mounts to the driver side fender apron with two nuts. Bare block without brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available. Ford casting # D0OA-2B328. *NOTE* Starting in 1970 there was a built in proportioning valve. **NOTE** Sometime during the 1972 model year there was a change from the D0OA-2B328-D casting number distribution block. Check...

Used Distributor / 289-2V / for the 1967 Mercury Cougar / 1967 Ford MustangFord part number  C7OF-12127-J  

Used Distributor / 289-2V / Manual Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7OF-12127-A  

Used Distributor / 289-2V / Manual Transmission for the 1967 - 1968 Mercury Cougar / 1967 - 1968 Ford MustangCurrent distributor is dated 7B23, Feb 23, 1967. Ford part number C7OF-12127-D  

Used Autolite distributor with the Ford part number of C7ZF-12127-F. This distributor was specifically used on 289-4V engines with manual transmissions. These used distributors should be considered rebuildable cores. Most will be complete, less the vacuum advance units. This is a tough one to keep in stock, the current one in stock as of March 2019 is dated 8D9 or April 8, 1968. Apparently, this distributor was used for Canadian cars with open emissions in 1968. So add 289-2V, 302-2V, and...

Used Distributor / 289-4V / Manual Transmission for the 1967 Mercury Cougar / 1967 Ford Mustang Ford part number C7ZF-12127-E Current distributor is dated 6L18, November 18, 1966.