All Products

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1970 Mercury Standard model Cougars and all Ford Mustangs with 20 or 22 gallon fuel tanks. This is an original 1970 fuel sending unit with one electrical prong. Ford casting number D0WF-9275-A. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3 prongs...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971-73 Mercury Standard model Cougars and all Ford Mustangs with 22 gallon fuel tanks. This is an original 1971-73 fuel sending unit with two electrical prongs. Ford casting number D1ZF-9275-AB. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3...

This used fuel / gas tank shows small dents on the underside but the top side is perfect and the inside has no corrosion. This tank would be good for "splitting" and combining this good used upper half with a reproduction lower half. We recommend converting to the non-evaporative 1970, 49 state tank, unless concours is desired. Conversion requires 1970, 49 state style filler neck and filler hose. We prefer that you come to pick this one up as we cannot ship anything that smells like...

This grille will be less than perfect with one or two cracks, bend showing and pitting. A Grade "C" WILL be cracked around the perimeter, but will not be missing any pieces. Good for a driver quality car.

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

1971 *351-4V after 4-12-1971. 1971 429 CJ. 1972 with "Sporty" dual exhaust. Engine designated as a 351-CJ on air cleaner lid. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-D. *Late production - after April 12, 1971.

1971 *351-4V prior to 4-12-1971. 1972 and 1973 351-4V with "Quiet" dual exhaust. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-B. *Early production prior to 4-12-1971.

Mounts to the rear of a 'turbo' style muffler. Left side bracket. 289, 302, 390, 427, 428, all with dual exhausts. Ford part number C8WY-5260-E. *Early production prior to 11-1-1967

Mounts to the rear of a 'turbo' style muffler. Left side bracket. 351W, 351C, 390, Boss 302, 428CJ - all with dual exhausts. Ford part number C9WY-5260-B.

Currently out of stock. Do you have a pair for sale? Let us know! Four required per car, bolts to the back side of the upper portion of your 1968 seat frame. According to the 1968 Cougar assembly manual the Ford part number is C8ZB-65610B10. This part has an adjustment to fine tune the headrest post alignment.

This option requires you to PRE-PAY a $50 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL RECONDITIONED ACTUATORS COME WITH A ONE YEAR WARRANTY. *NOTE - Reconditioning on these actuators involves replacing the shaft seal and dust boot, we do not service the internal diaphragms. You...

We have finally found a supplier that produces the correct DARK BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

The 1971 - 1973 Mercury Cougar XR7 came with Tier and standard came with Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Reproduction frame used to stretch your headliner over on the interior side of your sliding sunroof panel. Since we do not have near enough of these to go around we also offer a cardboard template for purchase for those of you that would like to make your own. With the pictures we provide and the template one should be able to produce a reasonable reproduction. 

Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...

D0OZ-9652-A Heat shield 'S' tube unique to 1970 351 Cleveland engines 2v or 4v. *Note - Must be used in conjunction with the heat shield part number D0OZ-9A603-F and air cleaner snorkel part number D0OZ-9A626-D.

Ford part number D2AZ-9A603-D (outer section) and D2AZ-9A603-B (inner section) make up this two piece metal shroud for all 1972 - 1973 H code 351-2V engines. The outer shield section is common to both 2V and 4V 1972 - 1973 351c engines but the inner is unique to the 2V.

Ford part number D2AZ-9A603-D (outer section) and Ford part number D2AZ-9A603-C (inner section) make up this two piece shroud for the 1972 - 1973 Q code 351-4V engine. This inner shield conforms to the 351-4V cast iron exhaust manifold only and the outer portion fits both the 2V and 4V.

Grade A exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade A used will only have minor pitting, it will have no holes or rough rusted edges. We also stock B grade versions for less than half the money.Replaces Ford part number D0OZ-9A603-F.

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

Heater control bezel for Mercury Cougars without A/C. Assembly includes grade A bezel, you will want to paint with your exact dash color. Check back often, this type and grade of part is seldom in stock very long. Ford part # C8WA-18531-A.

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

THE QUALITY ON THESE HOOD SCOOPS HAS DECLINED GREATLY, AS OF NOW WE WILL MOST LIKELY NOT BE ORDEREING ANY MORE UNTIL THE ISSUES ARE CORRECTED. Reproduction Eliminator hood scoop for the Mercury or Ford. Correct stud configuration, size and weight and far superior to our old scoop we offered. This scoop was made by using an original Eliminator scoop to make the mold. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. This...

As decades old Cougar lore goes... After Dan Gurney test drove the XR7-G for the first time he was asked what he thought about this new Cougar. His supposed reply was, "you can't hear the horn at high speeds." The car was later equipped with this third horn just for Mr. Gurney. Anyway, that is how the legend goes.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Used grade "A" horn center / pad in light blue fro the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased separately. *Restoration...

All 1967 390 Cougars with California emissions. Special molded hose see diagram. Connects the smog pump and air inlet assembly.

[No Description Provided]

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. Kit includes used check valve and fittings shown, but does not include headlight switch. "I found a good way to...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. "I found a good way to remove 50 years of crud. Soak the lines in hot water and dawn dish soap for a bit then take a...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here!NOTE:...

This is what is referred to as a campaign part. It was found that the early 1967 Cougars were having some issues with the headlights and this revised hose kit with ground strap was the fix. Often these have been found opened on dealers shelves with the "near new" take off hoses placed back in the original box. This is a great find for the guy wanting to do a concours restoration on his 1967 Mercury Cougar. Not for use on a 1968 as the switch was located under the dash as opposed to next to the...

This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. Includes both Pressure and Return hose that connect to the control valve. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against...

The tubbing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find these at your local auto parts store or the the "Mustang Discount" folks. Replaces Ford Part Numbers: C7OZ-3A719-A, C7OZ-3A719-C, C7OZ-3A713-A, C7OZ-3A713-C, C7OZ-3A713-D. Please Note: We highly recommend upgrading to the large nut (5/16") control valve as the small nut (1/4") control valve posses a potential safety issue, thus the reason why Ford replaced it the...

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang with or without Power Steering Cooler.  Be sure to select the option to...

This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...

Premium power steering hose kit for the 1970 Cougar or Mustang with a small block.

[No Description Provided]

Used grade "A" simulated wire spoke hubcap / wheel cover that is in excellent condition with no curb scrapes, stress cracks in plastic center or pits in die-cast. Ford part # C7WY-1130-C.*NOTE* You will often see this same cap with the Mercury head center and a red background. This cap is not correct for Cougar, but was found on other Mercury products such as the Montego.

Used Grade A hubcap, which was available optionally on any 1970 Mercury Cougar, these were called Rallye hub caps. We believe that these were special order and a mid year introduction to the 1970 Mercury Cougar. Called out on Marti Reports as 'Rallye Wheel Cover', and have been documented on Mercury Cougar Eliminator and XR7, as well as standard model Cougars and convertibles. Grade A will not have noticeable scrapes from the curb. Very uncommon hubcap, we never have grade A full sets in...

Used Grade A Rallye hubcap, which was available optionally on any 1970  and newer Ford Torino, Ranchero, etc. these were called Rallye hub caps. Called out on Marti Reports as 'Rallye Wheel Cover'. Grade A will not have scrapes from the curb. Fairly uncommon hubcap, we seldom have full sets in stock. The cap intended for Mustangs had a running horse emblem in the center.Replaces Ford part number D0OZ-1130-D.*Note - This cap is only intended for 14 X 7 stock steel wheels wheels. ...

Brand new cap, sometimes the boxes are missing due to age.Ford part # C9WY-1130-C.Fits:1969 Mercury Cougar Standard1970 Mercury Cougar Standard

NOS turbine style hubcap / wheel cover for the Mercury Cougar and Montego. These are the same as the 1969 Sports Special / 1968 Dan Gurney hubcap / wheel cover, but have the Mercury logo glued in the center. Ford part # C8GY-1130-G. Fits: 1968 Mercury Montego

New Old Stock XR7 hubcap / wheel cover for the Mercury Cougar. There were two versions of this cap, one with a white painted ring around the center, and one with black around the center. The white version was used in 1969, with the black version being used in 1970. Ford part # D0WA-1130-A

NOS Grade A XR7 turbine style hubcap / wheel cover for the Mercury Cougar XR7. This unit was factory installed on the XR7 and was a one year only hubcap / wheel cover that has 22 black ribs. The Mercury MPC states that these caps were not to be sold in Pennsylvania. Ford part # C8WY-1130-D.Fits: 1968 Mercury Cougar XR7

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...