All Products

289 and 302 engines - with C4 automatic transmissions or manual three / four speed. Shaft diameter will measure 3 inches. Length 54-3/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.  Ford part # C7WY-4602-E.*NOTE* This is a solid one piece drive shaft.

Select 1970 M-code 351-4V engines and FMX transmission.Shaft diameter 3-1/2 inches. Length 53-9/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Not a common part, currently out of stock.Ask about slip yokes. Shipping is oversized due to length.

Flow thru ventilation, power vent, power ventilation system, comfort stream ventilation, are some of the various names for this rare option found on 1969 Mercury Cougar, Ford Mustang and Shelby Mustang. Back in 1969 it was a $40.02 option. It allowed fresh air to be blown through a center vent. Often confusing, because it looks like half of an air conditioning system.Ford casting number C9ZA-18C299-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to...

Edelbrock Torker 351C intake manifold. Edelbrock 2760 for 351C-4V cylinder heads. Used piece, single plane. Check the Edelbrock site for the specifications.

Used original 1969-70 Mercury Cougar Eliminator dash center plate with cover. Not reproduction, notice the slight shrinkage inside the chromed bezel? Only found on Eliminators. 

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fits many 1967 - 1968 Full size Mercury cars and 1967 - 1969 Mercury trucks. This emblem measures 6 3/8" total width and the "M" is 2 1/8" tall. The bottom mounting studs located on the letter "M" and "Y"...

NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.

NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.

Ford part number is C7WY-16098-A, casting number as seen on the back of the emblem is C7WY-16720-A. Very rare find, only used on 1967 non GT cars equipped with the S code 390.See related item Barrel nut if missing attaching clips. 3/16 inch stud.

Used Grade "A" center grille emblem for the 71 - 72 Standard Cougar. Most likely will show some fading, no pits. Ford part number D1WY-8A223-A

Original part in Ford box, part number C9WB-16098-A, casting number as seen on back is C9WB-16098-B

This Mercury script emblem is mounted onto the driver side fender extension. This is an original part still in the Ford box, engineering number on the back of the emblem reads C7WB-16098-A, Ford part number is C7WY-16604-A.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Rare Cougar only GT emblems. The Mustang GT emblems had different stud locations. These were used on 1968 Mercury Cougar GT models.  This emblem shares the exact same pin locations with the 1968 6.5Litre emblem, so the factory could punch holes and installed the tubular nuts in the fenders of all S and X code Cougars, allowing either emblem to be installed. The 1967 GT emblems have an entirely different stud placement from these 1968 only badges. Letter "G" is Ford part...

This is the correct emblem that came in the center of the hood moulding on a 1973 XR7 model Mercury Cougar. The price is absolutely ridiculous, I agree. Years ago when they sold for $250 I thought THAT was insane! Replaces Ford part # D3WY-16637-B.

Very difficult to find, delicate aluminum quarter panel emblem in the original Ford box. Ford part number is C9WB-6525622-A, casting number on back reads C9WB-65291B62-AYou can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines.

Regardless of what you have been told these emblems were never chromed. We do not have any of these in stock, probably will not get any more but we post this so as to give you a reference as to what color they should be.

Found on the C pillars of a 1971 - 1973 Mercury Cougar XR7 Coupe. We rarely get good used examples of these emblems as they are always badly faded. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.

COMING SOON Beautiful reproduction C pillar emblem for the 69 - 70 Cougar XR7. This part is also known as the shield or outside roof side ornament. The attention to detail on this exact copy is really impressive. Kudos to Daniel Carpenter Mustang for providing yet another outstanding part. Sold individually, 2 required per car. No core required. Replaces Ford part number: C9WB-65517A56-A Black plastic backer engineering number reads C9WB-65517C00-A Engineering number on back side of chrome...

This is a used coral with a new background decal and walking cat emblem. We ship the three parts unassembled so you can re-chrome the corral if you desire. The corral will not be perfect but it will not be heavily pitted either. You can expect the part you receive to resemble the one pictured here.Casting number: C9WB-18B000

These two emblems were sold separate when ordered as a service replacement part. We sell them as a pair. Located on the passenger side of the trunk, these are a peel and stick with no mounting studs. Ford part # C9WY-6542532-A & C9WY-6542532-BWe often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the...

Used emergency / parking brake assembly for a Mercury Cougar or Ford Mustang as removed from a West Coast Cougar organ donor. This unit may have some minor rust. Normally we assemble with reproduction cable.Ford part # C7ZZ-2780-B.

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang and is as removed from a West Coast Cougar organ donor. 1969 had a weak design and the release levers were prone to bend and break off. 1969 used a T shaped chrome release handle and 1970 used a black plastic T shaped release knob, which generally aren't interchangeble. Seldom in stock, please check out the reproduction version.

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang. The 1969 model used a T shaped chrome release handle and 1970 used a black plastic T shaped or chrome release knob. Seldom in stock, please check out the reproduction version. Ford part # D0ZZ-2780-A.

This Big Block motor mount bolts to the driver side (left hand) of the engine block. This original plate with the "L 427" stamped into the bracket. Fits 1968 Mercury Cougar GT-E with 'W' code 427 side oiler engine. A regular FE Cougar driver side will work with modification.  Ford part # C8ZZ-6046-C for the left hand bracket

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

D0AE-9431-A 351-2V Cleveland, factory original cast iron exhaust manifold for driver side. At some point there may have been a D0AE-9431-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some after-market aluminum intakes such as one offered by Edelbrock.

D1ZE-9431-CA 429 Cobra Jet factory original cast iron exhaust manifold for driver side. At some point there may have been a D1ZE-9431-CA1 or a D1ZE-9431-CA2 casting number used, either of which may be substituted as per the Master Parts Catalog. The current manifold in stock has a casting date of 4-28-70.

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Used only on cars exported where speed limits were posted in KPH. Good used and working speedometer from 1969-70 XR7's and Eliminators. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work correctly. 1969 and 1970 XR7 speedometers all look exactly the same, but the 1969 part number is...

This extension holds the inner spring tube in place on the 70 - 73 tilt column. Fragile piece, should take great care when tapping on this pot metal piece. Limited supply. Ford casting number: D0ZA-3790-*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Near new take offs with not a single mark on any of the four. If you buy all four we will discount them substantially.Rim Width:8.5Brand: Factory Rim Diameter:17Interchange Part Number:3831Offset:+34Quantity:1Rim Brand:Factory, OEMNumber of Bolts:6Manufacturer Part Number:BL3V1007AA/BARim Material:AluminumBolt Pattern:6x139.7

NOS fan clutch for the Mercury Cougar or Ford Mustang. This unit was used on 1968 Cougars and Mustangs that were produced before 12/1/1969 and equipped with the 302 engine. It was also used on the 1969-70 Cougar and Mustang equipped with the 351 engine.Ford part # C60Z-8A616-E

D1ZE-8146-AA fan shroud for any 1971-72 Mercury Cougar and Ford Mustang with 351 engines and either air conditioning or extra cooling.

New old stock 1969 Mercury Cougar Driver Side Front Fender Extension Ford part # C9WB-16A169-B, Mercury MPC # C9WY-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help.

Our grade "A" 1967 - 1968 fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Hardware not included but if you ask for it we will try to include it at no charge. Note that the inner part just behind the eyebrow moulding is painted black from the factory.Ford casting number as seen from the back side reads C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. This icon means that we're looking to buy this...

These used original plastic fillers mount to the hood extension, and filled the gap between center grille surround (extension) and the side grilles. Very rare to find a 1970 Mercury Cougar with both of these intact as the driver side often got broken when someone reached in the recess for the hood release latch. These feature the original Ford part numbers. Sold as a pair only. Original Ford parts, these will seldom be in stock. Typically the ultra rare driver side may have a defect or small...

Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.

NOS flip lock cover for full sized Mercurys. We aren't sure if this for the trunk or the station wagon.

Green floor mats for the 67 - 73 Cougar embroidered with the walking cat and Cougar script logos.

1967 - 1973 Cougar Logo Rubber Floor Mats - Used Dark chocolate brown, correct for Cougars equipped with Saddle, Ginger, or Tobacco interior. Notice this set is the version that is a couple of inches narrower so it will fit well with the addition of convertible inner rockers.

This part is located in the left front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L09-A

This is a used fuel door insert we have cleaned up, painted the background black and installed a 1967-1969 headlight door walking cat emblem on. The original 1970 ELIMINATOR piece that this resembles had a smaller sized cat so this is not exactly correct for your original 1970 Eliminator.

Reproduction OE steel fuel tank to pump two piece fuel line with 3/8" fittings for the Mercury Cougar equipped with the factory rear sway bar. This also includes Eliminator models.*NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1969 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1969 fuel sending unit with 3 prongs (2 electrical and 1 alignment prong). The original Ford casting number was C9WF-9275-C. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely interchangeable on all 1969 20 gallon fuel tanks. *Note -...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1967 Mercury Standard model Cougars and all Ford Mustangs with 16 gallon fuel tanks. This is an original 1967 fuel sending unit with one electrical prong. Ford casting number C7ZF-9275-C. This unit comes with a new 5/16 inch filter, brass float, and sending unit gasket. The only difference between this sending unit and the 1968 sending unit is the diameter of the pickup tube. The 1968 verison of this...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1968 Mercury Standard model Cougars and all Ford Mustangs with 16 gallon fuel tanks. This is an original 1968 fuel sending unit with one electrical prong. Ford casting number C8ZF-9275-A, master parts catalog number C8ZZ-9275-C. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models or Ford Mustang with low fuel warning...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1969 Mercury Standard model Cougars and all Ford Mustangs with 20 gallon fuel tanks. This is an original 1969 fuel sending unit with one electrical prong. Ford casting number C9WF-9275-A. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3 prongs (2...