All Products

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2" and is a very good copy of the original. Made in America.

Used roll up door for the Standard Mercury Cougar's center console. Finished metal front and flexible rubber back. Includes chrome knob. Different from the 1968 door in that it has the much smaller handle. Ford part # C7ZZ-6506024-A.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The 67-68 Mustang...

Used roof mounted switch that is rather delicate. As you can see from the pictures, the chrome coating has started to peel slightly. 

Good grade A used jack with correct fine threads. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not. Grade A will not have rust or damage.

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A. Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Used (poor condition) weather strip may or may not be in place. Please go to our rubber section to select the new rubber strips...

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Sold separately, please choose between driver or passenger side. Used (poor condition) weather strip may or may not be in place....

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...

Sold as a pair

This is an example of the best set we can come up with. This is a standard set that has the black buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below.  ...

Sold as one-seat set including one bottom cushion and one backrest cushion.

American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process.NOTE: These foam kits work well on the Standard and Decor interiors but you will find on the XR7 the lower portion does not work well.

This Mustang combination foam kit consists of a 1966 Mustang Pony Interior upper and a 1967 Mustang standard lower portion. If you use this set of foam you will have to build the upper portion about 1" all over to get a good fit.  Here is a link to some good advice on the matter.  One kit consists of two parts, enough to do one seat.  This can also be used on the 1967 Cougar bench seat.  This is not an exact fit but of all the foam available it is the combination that...

Reproduction premium seat foam custom made specifically for the standard 1967 Mercury Cougar. Unlike the previous version we carried in the past, this premium seat foam does not require any modification to make fit. One set is top and bottom foam, enough to do one seat. NOTE: This seat foam is also used on the front bench seat.

American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process.This seat cushion foam is of a much softer lighter material than the other seat cushion foam that we offer. Much more comfortable and plush and about half the weight. Click on images to enlarge. ...

Finally, the much anticipated replacements for those worn out XR7 seat cushions are available!Sold Individually. * - We have received customer feedback that indicates this is seat foam works well or is easily adapted to work with the 1968 XR7 Interior or the 1968 - 1969 Decor Interior. Here is some feedback from a customer who adapted this 69 foam for his 68 XR7. Judging by the pictures he sent us, the results were very good. Hey Lin & Don, When I ordered the 1969 XR-7 front seat foam from...

Reproduction seat divider insulation pad. Made from ABS plastic with a foil type backing and a layer of jute in between. Designed to fit with very little trimming, this divider will suppress excess noise coming from the rear of the car.

Bottom seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. We highly recommend used cores as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Driver side shown.

Used driver side bottom seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. Most times customers will only need the bottom portion, and it saves on shipping costs compared to shipping a whole seat frame. 

Bottom seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. We highly recommend used cores as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Driver side shown.

Used passenger side bottom seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. Most times customers will only need the bottom portion, and it saves on shipping costs compared to shipping a whole seat frame.

Good used platform that is unique to the convertible. This will have a couple of thin spots but will be functional as is with all four mounting areas in good condition. This part is rarely in stock due to the lack of convertible parts cars with usable floor parts.

Good used platform that is unique to the convertible. This will have a couple of thin spots but will be functional as is with all four mounting areas in good condition. This part is rarely in stock due to the lack of convertible parts cars with usable floor parts.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The bench seat brackets are slightly different than the bucket seat brackets. Our premium grade used tracks are carefully inspected for damage before shipping. Most likely you will have to paint but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. Ford master part numbers...

Bucket seat track set for all 1971-73 Mercury Cougar and Ford Mustang. New manufactured, this is a product of Taiwan. One set is enough to do one seat, mounting hardware is sold separate. Kit includes D1ZZ-6561704-A, D1ZZ-6561705-A, and C5ZZ-6561726-A. Limited supply.*Note - Not compatible with the power seat option.

This listing is for the person who needs a little more leg room when behind the wheel. If your knee is pushing on your turn signal lever, or if your belly is hitting your steering wheel, this is the item for you. Very easy to install, bolts right up to your existing seat tracks. You can expect about a 1/4" height difference. Sold as a pair, enough to do one seat. Check out this video

Thoroughly tested and working sequential assembly as found in the trunk, for the early (inception until 1-3-1967) built 1967 Cougar. Check the wiring in your car to make sure this is the one you need.We test these on a mock up board that has fresh bulbs, cleaned connections, cleaned grounds, etc, basically ideal testing conditions. Detail cleaning electrical contacts and grounds on your car goes a long way to making your electrical components function properly. We will warranty these used...

Thoroughly tested and working sequential assembly as found in the trunk, for the late (from 1-3-1967 until end of model year) built 1967 Cougar. Check the wiring in your car to make sure this is the one you need. We test these on a mock up board that has fresh bulbs, cleaned connections, cleaned grounds, etc, basically ideal testing conditions. Detail cleaning electrical contacts and grounds on your car goes a long way to making your electrical components function properly. We will warranty...

Thoroughly tested and working sequential assembly as found in the trunk of all 1968 Cougars. We test these on a mock up board that has fresh bulbs, cleaned connections, cleaned grounds, etc, basically ideal testing conditions. Detail cleaning electrical contacts and grounds on your car goes a long way to making your electrical components function properly. We will warranty these used units for 90 days from purchase. We highly suggest using our modern solid state unit as these were never...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 390 or 428 Cobra Jet FE big block 1967-68 Mercury Cougar and Ford Mustang with automatic transmission.Ford part number C7ZZ-9725-A.

Used lower shaft used in the tilt / tilt away steering column found in the 1968-69 Mercury Cougar or Ford Mustang. This is the portion that mates with the upper shaft that bolts to the steering coupler. Overall length of this shaft is 15-11/16 inches long.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This 1967-68 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390-427-428's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found on all 1973 Mercury Cougar or Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little more ergonomic in design, compared to earlier designs. Core charge applies.Replaces Ford part number D3OZ-7213-A.

Get a grip with this reproduction Hurst T handle, or shifter handle, for the Mercury Cougar or Ford Mustang equipped with a manual transmission. Threads are 3/8-16. Check out our video on rebuilding your shifter below: ...

Very hard to find 69 - 70 Shelby / 67 - 69 Cougar 4 speed shifter knob. Almost a year in development was spent to get as close as possible to original N.O.S. sample. These very rarely come up for sale used and when they do, they are expensive. Knob insert is made of metal just like original not brass. Knob also has the correct groove in middle of body like 69 version and not the earlier version which does not. Not technically correct for a 67-8 Cougar, as the 67-8 does not have the groove in...

Used on both XR7 and standard Cougar consoles. Differs from shifters made for non console use in that is has a small loop to connect the white plastic arm to the shift indicator light. Fits 1967-68 Mercury Cougar and Ford Mustang with factory consoles. Good used part no heavy pitting on the chrome, comes with complete with cable assembly inside. Ford part number C7ZZ-7210-C. Check out our video on rebuilding your shifter below: ...

Factory detailing and triple chrome plating distinguish these tubular shift handles from the rest. Non-functional T-lever included. American made for quality workmanship. Replaces Ford Part #: C5ZZ-7210-T. Check out this video

Check out our video on rebuilding your shifter below:

This quality reproduction 1967 Mustang part can easily be made to fit your 1967 - 1968 XR7 or 1967 standard Cougar manual transmission console simply by drilling the two holes near the front for the spring clips that attach the pad to the console. See the diagram below for correct hole size and location. This plate was used on both three and four speed manual transmission Cougars equipped with the optional center console. Not for use on 1968 standard / decor consoles. Replaces Ford Part #:...

D0ZA-7E046-D Reproduction adapter plate for mounting the Hurst 4 speed shifter control assembly to the Top Loader transmission. 1970 Mercury Cougar and Ford Mustang big block 428 Cobra Jet 4 speed only. Ford master part number D0ZZ-7E046-A. Link to the expert on Ford shifter linkages. Check out our video on rebuilding your shifter below: ...