Wanted!
Buy
Details
Availability: Out of Stock
Item #: 15-0046 -
One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...
Wanted!
Buy
Details
Availability: Out of Stock, On Order
Item #: 26131 -
This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety standards. The mirror nut tool will fit over the 1967 wand, but not the 1968.
Wanted!
Buy
Details
Availability: Out of Stock, On Order
Item #: 26151 -
This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 23780 -
Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 19483 -
These used taillight mounting washers are sold individually for your Mercury Cougar. Two different inside diameters on these, we have them mixed, because they are in such short supply. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 30938 -
Reproduction concours weave black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown...
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 24225 -
Good used crank correct for 1967 XR7 or standard models. No obvious blemishes, driver quality. The Ford part # is C5ZZ-6523342-C, casting number as found on the back reads C7ZB-6523348-A.
*Customer Feedback* Don, Lin and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy with the condition and the service! It has been less than a week since I ordered them and they arrived via USPS, as per requested, with a very...
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 10805 -
Trico brand wiper blade refills for 1969-70 Mercury Cougar or Ford Mustang with original wiper arms
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 23768 -
1967 was the last year for the 3/8"-16 threads. We also carry the J bolt C6OZ-1448-A, and the top plate or disc C5ZZ-1424-A.
Wing-nut, spinner. *NOTE* The original 67 wing nut had no protruding tabs in the recessed area as did most of the 1968 - 1973 wing nuts.
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 32826 -
Used wiring pigtail that runs from the under hood harness to the starter solenoid (battery side post) on the 67 - 68 Standard and XR7 model Cougars.