All Products

Used on two spoke steering wheels. Replaces Ford Part # C0DZ-13807-A. Although it does not "look" right it will function correctly. Those in the know will purchase our good used spring.

Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

The 1969 - 1970 windshield washer kit varies slightly from the 67-68.Replaces Ford part #: C9ZZ-17543.

Replaces Ford Part # : D1ZZ-17543

The 1967 - 1968 windshield washer kit varies slightly from the 1969 - 1970. Replaces Ford part #: C7ZZ-17543.

Reproduction 1/2" hose clamp, commonly used on the fuel lines. This clamp is smaller than the ones used on the power steering return line.

Reproduction Power Steering Return Line Hose Clamp for the 1967 - 1973 Mercury Cougar

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Power Steering hose bracket insulator for both the small and big block brackets for the 1967 - 1970 Mercury Cougar and Ford Mustang. Replaces Ford part #: C7ZZ-3A609-A or C7ZZ-3609. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are things coming to? Where is...

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Original Ford part number 373845-S.

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Dimensions: 3/16 x 3/16 x 1/4

Sold individually # 377112-S

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

New sealed bearing for installing on your 1968-69 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing is physically smaller than the bearing used on the 1968-73 idler pulley (1968-73 bearing sku: 10462). The 1968-73 idler pulley assembly came as a "service replacement" on 1968-69 cars. The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 3/8". On the larger bearing pulley, this measurement is 1 9/16". Both versions of...

Made by the original supplier! Replaces Ford part # C9AZ-11582-A Here is a helpful "How To" youtube video on how to replace your ignition switch.

Reproduction Ignition Lock Sun Visor Instruction Sleeve Decal for the 1970 Mercury Cougar or Ford Mustang 

Used indicator lenses for the 1969 Standard fuel gauge. Taken from a used gauge, they will be in the best shape possible, no serious wear, no breaks and no cracks. Lettering will be legible and intact. Diffusers are also available.

Used indicator lenses for the 1970 Standard fuel gauge. Taken from a used gauge, they will be in the best shape possible, no serious wear, no breaks and no cracks. Lettering will be legible and intact. Diffusers are also available.

Used indicator lenses for the 1970 Standard temp gauge. Taken from a used gauge, they will be in the best shape possible, no serious wear, no breaks and no cracks. Lettering will be legible and intact. Diffusers are also available.

Reproduction dust and safety plate for all C4 (code W) automatic transmissions also known as the Cruis-o-Matic transmission. Inspection cover for torque converter and flexplate.NOTE - Although the C4 and the FMX inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Reproduction installation kit for the 1969 Cougar dash pad.

Reproduction installation kit for the 1970 Cougar dash pad.

Replaces Ford Part # C9ZZ-10914

Insulator for mounting the ammeter on any 1969-73 Mercury Cougar or Ford Mustang with factory ammeter in gauge cluster. Also used on other Ford cars with ammeter. Casting number C9ZF-10C914.Replaces Ford Part # C9ZZ-10C914

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

Reproduction Rear Leaf Spring Center Mount Insulator Pad for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody StyleNotesYearMercur...

These were used to mount the Fuel, Temp and Oil gauges on both Standard and XR7 models. Includes 2 mounting nuts.

LED dome light bulb for the standard (non-XR7) 1791, 1972, or 1973 Mercury Cougar.

Used on both the Xr7 and Decor / Deluxe interiors with moulded door panels.

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

Multiple uses.5/8" from bend to center hole.

Replace FORD Part #: C8WB-17093-B

Replaces Ford Part #: C8WB-17093-D.

Correct for the 1969 Eliminator SS wheel. Replaces Ford Part #: C9WB-17093-B

Under trunk lid decal for 1968 Mercury Cougar and Ford Mustang with style steel wheel spare tire. Jack usage and spare tire stowage, shows the unique round disc for use with style steel wheels.

Replaces Ford part #: D1ZB-17093-AD.

For use on Hard Top / Coupe.

Replaces Ford part #: D1ZB-17093-CE

This decal goes on the tire jack itself.

Notice this shows a picture of a Mustang not a Cougar and shows the handle on top instead of the disc. This decal did in fact find its way onto some Cougars in 1967. Replaces Ford Part # C7ZB-17093-D. "CZZB" typo on decal can be seen on some originals. We see this decal with the typo and without on original cars.

Reproduction Jack Instructions Decal for the 1971 - 1973 Mercury Cougar

Used jumper wire with correct ends for doubling back on the tachometer leads from the under dash harness. Works for all generations 1967-68, 1969-70, and 1971-73 Ford anything and Mercury, and Mercury Cougar with factory tachometers. If your tachometer goes bad, you will not start or keep your engine running. Good for bypassing tachometers for testing and getting home. Keep in your glove compartment or tool box.

Reproduction keeper clip that attaches to the secondary articulating stabilizer arm and slides into place to secure the pin that holds the arm.

Chrome screw used to mount the rear interior panel keeper.Sold individually.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.