All Products

Used plastic rocker moulding clip for 1968 Mercury Cougar and 1967-68 Ford Mustang. Used clip, originally pop riveted onto the rockers. Sold individually. Ford part number C7ZB-6510182-A.

This clip fastens the vacuum motor to the locking pawl rod. One required per car. Fits 1967 Ford tilt-tilt away columns only. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired.

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet.Sold individually. 2 rollers required per window, 4 rollers required per car.Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" DiameterHere's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Replaces Ford Part #: C0AB-6423240-B. Four required per car, two per side. If your quarter glass is loose in the track and will not roll up and down these rollers are most likely the culprit. When the tracks get gummed up and the window takes too much effort to roll up and down, these brittle old rollers will break. Even if they are not broken they are often frozen in place from rust and will not spin freely. From our experience every 1967 - 1968 Cougar needs these replaced if they still have...

Used single plastic roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Note that there is only one of this style of roller on each quarter window. This is a simple white plastic roller and a rivet. Note that there are 2 rollers with 2 pieces of round white plastic. Often times one of the rollers breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the...

Reproduction rubber roller for the metal tilt cover plate on any 1968-69 Ford, Mercury, or Lincoln. Often times the rubber disintegrates over time. This is needed to keep the cover plate tight to the side of the steering column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Two required per car.Replaces Ford part # D1ZZ-6522244. Sold individually

Reproduction roofrail weatherstrip seal clip and quarter window guide clip for the 1971

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo.   1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

Unfortunately the premium version is no longer available.  This version is made of a softer compound than the original bumpers and will not hold up as long as the originals did on a Cougar due to the force that the actuator exerts.  Sold as a Pair. Check out this video Check out this video

These were installed only on early production 1967 Cougars but can be installed on any 1967 Cougar. Later in the year they quit installing these and just used a rubber plug to fill the hole. 1968 was not drilled for these. Sold as a pair.

These small rubber protectors slip over the metal tabs in the trunk that hold the taillight wiring loom to the body. They protect the wiring from abrasion, and are often missing. Sold individually.

Used rubber sleeve from the front outer bumper mounting tube bracket. Must be for anti squeak or for protection of the front turn signal wiring harnesses. One per side, sold individually. The Ford part number for this item is C7WB-17B947-B. These were made from rubber tubing with a wall thickness of 1/8 inch. Inside diameter is approximately 7/8 inch, and about 1-1/2 inches long for these 1967-68 bumper sleeves. Limited to available stock.  ...

Automatic chokes had been the norm for many years so a notice to the operator was a must. Decal Text:NOTICEThis vehicle is equipped with a manual choke located immediately below the ignition switch. For proper starting use manual choke. ...

Sold as a Kit as Pictured.

Sold individually Zinc with Bi-wax sealer (dark silver with gold color on threads)

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold individually, three per side, six per car required. These often get destroyed when you go to replace your door window regulator slides. Three of these are used to install the C7ZZ-6523288-A track. Stainless steel.Thread size: 8/32 Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator?...

For attaching firewall sound deadening material to any 1967-68 Mercury Cougar Standard or XR7. 

New hex head screw for attaching the fuel filler neck to the rear body. 67 to 70 Mercury Cougar and 1965-70 Ford Mustang. 1965-68 filler necks require 4 of this style screws. 1969-70 filler necks require a total of 5 hex head screws. #10 x 3/8". Replaces Ford number 42120-S8.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

Original style fuel tank installation screw. 3/8 inch hex head. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks. See item 11942 for the kit of 12 screws, better value.

Original style fuel tank installation screw kit. 3/8 inch hex head. This is a set of 12 new screws. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks.

Sold individually. Two needed for globe box cable 1967-70 Mercury Cougar. 3 needed for installation of turn signal switches 1967-73 Mercury Cougar or Ford Mustang.Ford number 379203-S. Phosphate & Oil (gray-black)

Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.

New black screws for attaching the headlight doors to all 1967-68 Mercury Cougars. Four screws needed per side for a total of 8 per car. We have found 3 different styles of separate screws that were used during the 1967-68 model run, San Jose and Dearborn may have accounted for a difference. This one matches exactly to one of the more common ones that were installed. Replaces Ford Part number 376352-S15.

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually. Zinc (dark silver)

Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Sold individually.  24 required per car, set of 24 also available. ...

Special Phillips pan head screw for attaching the pancake motor to the quarter window regulator. 1969-73 Mercury Cougar and 1971-73 Ford Mustang. Weird threaded screw, called a triangle threaded screw. Slightly larger than 1/4-20. Unique and limited to quantity on hand. Three screws per regulator, sold individually. Ford part # 381530-S. *NOTE* For those of you who like to rebuild and refurbish your own parts, check out our video below. It will take you through the pancake motor...

Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

New screw for attaching horn pads onto steering wheels 1968-69. 2 or 3 required, sold individually.

Used unique Phillips bright finish screw that attaches cable guides to roof.

This is a very specialized screw that you do not want to fail or make do with an incorrect fitting or stripped screw. When removing your old screw you will most likely have to pull your pedal assembly and have a perfect fitting screw driver to remove the screw as the factory put them in 3-6 foot lbs.Ford part number 380503-S8.

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Correct size, style, and color screw for all 1969-70 Mercury Cougar front turn signal bezels. Sold individually, 4 total needed per car.Replaces Ford part number 52445-S.

Zinc plated screw for attaching the stainless steel upper quarter glass channel onto the quarter window frame. Two screws needed per side

Screw for mounting wing window pivot bracket. Two per car

8-32 screw for attaching the window regulator drive arm slide

One kit does both rear armrests for the XR7 or Standard interior coupe.

"Correct" for 1968 Standard or XR7.Includes:(2) #8 X 3/4" PH PN AB ZC screw with a Electrolytic Zinc & Wax finish(6) #8 X 3/4" PH OV AB 6HD ZC screw  with a Electrolytic Zinc & Wax finish