All Products

Rear Valance Hardware kit contains 2 bolts, 2 clips and 2 nuts. "Almost" correct reproduction that functionally works great. Plated to prevent rust.See related items for a more complete fastener kit, which includes the pan head Phillips screws. Replaces Ford Part #: 372719-s100.

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...

D1AZ-6788-A Metal tab that bolts to the intake manifold and has a hole for the round hose retaining ring (part number D2AZ-14A163-K). 1972-1973 all 351 engines, *Restoration Tip - These were painted Ford engine blue when the engines were painted, so paint it Dark Ford engine blue.

Mounts on floor pan above the center of the rear axle over 3rd member on small block cars with 8 inch rear ends. Mustang only, will not fit a Cougar.Replaces Ford part #: C5ZZ-4730-B orC3AZ-4730-B. Customer Comment:Thank You Don and WCCC,Copy Cat's almost done!Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product.Without their patience and understanding along with a great selection of parts I wouldn't have her in such great shape.Thanks guys, along...

(7526) Nylon plastic injected. New Old Stock. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where...

D1ZZ-6523258-A Black plastic bolt-in door glass bushing. Used on 1970 bolt in door glass and 1971-73 door and quarter glass. White was used in early 1970, and black from 1970-73. There was some overlap in 1970. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

New carburetor spacer gasket, goes between the intake manifold and spacer plate. 1969 S code 390-4V or 390IP. Upper gasket, spacer plate to carburetor here.

Headlamp center shaft actuator rod clips. Sold individually, two clips needed, one on each side of the shaft. Not really needed, probably kept the shaft ends from moving during installation. We have found two different sizes of these clips. No pattern between 1969 and 1970.

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Two of these clips per side are required to hold the interior padded pillar pads the the "A" pillars on your 1968 Cougar.Replaces Ford part number 381896-S2.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

This fragile little clip attaches to the bottom outer edge of the front fender extension and holds the tail of the aluminum eyebrow moulding to the extension, one per side. They almost always fail when you remove them, and to be honest, we rarely have them in stock. We do not list these hard to find parts to tease you, but rather for documentation purposes. We do offer a nice reproduction clip that you can get right here that will work great. ...

Used plastic clip for the Mercury Cougar or Ford Mustang.

Factory used clip for attaching the long black plastic rear bumper filler on any 1971-73 Mercury Cougar. A total of 8 clips are needed to attach the rear bumper filler. Most have either broken with age, or have broken during the removal of the filler. Sold individually. Limited supply of used, we also stock a suitable reproduction clip. See Related.

Clevis type attaching clip for attaching the accelerator throttle rod to the carburetor on all 1967 and 1968 Cougars. The correct installation is with the clip pushed on from the top, barbs down. This is the right handed style.Original Ford part number C2VY-9826-A

NOS under hood plastic clip for the 1968 Mercury Cougar or Ford Mustang.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

Stainless Clutch Pedal Pad Trim. Replaces Ford Part #: C9ZZ-7B544-A.

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

This ultra rare NOS center cap decal features a black background and a chrome walking cat and was used when the 10 spoke 15" aluminum Shelby wheels were ordered for your Mercury Cougar. The wheels were marketed through Shelby American in the Cougar catalog titled, "How To Sharpen Your Cats Claws". I was able to obtain the last of their inventory through a previous employee when they closed the doors in the mid 70's. They measure 1-13/16" in diameter and fit well into the 3 bar spinners used on...

Reproduction 390 4V GT Emission Decal for the 1968 and 1969 Mercury Cougar / Ford Mustang

Here's the original "stereo" decal for the 69 - 70 door speaker grills. If you want to keep your car as original as possible, these are for you. These decals are made from aluminum, and as you know, they can get pretty flimsy after 45 years. We'll do our best to pick out good ones for you. You can get the sticker repro version here. SOLD INDIVIDUALLY. ...

This is a new, faithful reproduction of the rarely seen promo sticker that was created after the 1968 Cougar won Car and Driver magazine's Readers Choice Poll for Best Sporty Car. The winners were announced in the May 1968 issue. These were mostly put on the quarter window glass, but it's up to you where to show off your Cougar's status. This new decal is the same size as the original (2-3/4" x 3-3/8") and printed on mirror-shiny vinyl. The main difference is that the adhesive is on the back...

Nicely done reproduction with the only difference being that it adheres to the outside of the window and the originals adhere to the inside. Check out the very first Cougar in our video below! ...

C8AZ-6223362-A. Sold individually, has a different look than our reproduction decals.

Silicone and fasteners, everything needed for installation of our seat divider panel.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

Good used original handle with no obvious pitting or blemishes. This handle was not used on the XR7. Found on 1967 standard model Cougar and 1967 base model Mustang. Ford casting number C7OB-6222614-A.*Note - 1967 Mustang with deluxe interior, i.e. brushed door panels, used a similar handle, but with Ford part number C7ZB....

C5AZ-6221850-A Door lock knob for all 1967 Mercury Cougar and Ford Mustang. Additionally fits 1965 Ford full size cars such as Galaxie and Thunderbird. 1966-67 mid sized Ford Fairlane and Mercury Comet. Sold individually. Nice used condition.

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A

This green spring steel retainer fastens to the taillight mounting studs and keeps your plastic wiring harness clip in place. Six per vehicle, sold individually.

New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.

Fuel tank filler cap for all 1970 Mercury Cougars with California emissions. All cars with DSO numbers 52 & 53 came with emission controls that vented fuel fumes into a charcoal canister. This is a non-vented fuel cap, and only fits the specific 1970 emissions filler necks.

New replacement gas tank filler cap for all 1967-69 Mercury Cougars and 1970 Cougars without California emissions. This is a vented fuel cap.

Reproduction front seal for the Bendix brake booster used on all 69 - 70 Cougars and Mustangs as well as many other FoMoCo products that use this size of Bendix booster. This seal prevents brake fluid from entering the booster cavity once the master cylinder fails.

Made from fuel resistant cork like original. This gasket is specific to 1967 - 1968 Cougars. We finally found the correct gasket with correct hole placement (our other version which is good for Cougar AND Mustang has five holes, so basically you would have to drill through the cork just like they did in the Dearborn and San Jose factories).Here's a good tip! Ken Stein gave us this one...Install two of these gaskets and your gas cap will not scratch your paint. Original gas caps will always...

Reproduction Glove Box Catch for the 1967 and 1968 Mercury Cougar and Ford Mustang

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S