All Products

Basic C6 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C6 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that U code C-6 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Most complete kit available for rebuilding the early 1967 Mercury Cougar or Ford Mustang power steering control valve. Includes a very accurate sleeve, all 4 seats, and various seals and hardware. Please note that the early 1967 control valves did have 1/4 inch lines. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #:...

Most complete kit available for rebuilding the late 1967-70 Mercury Cougar or Ford Mustang power steering control valve. Includes a very accurate sleeve, all 4 seats, and various seals and hardware. Please note that the early 1967 control valves did have 1/4 inch lines. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #:...

Please remove your regulator prior to shipping. Be careful of the mechanical energy stored with the spring under tension.  This is a rebuild service for the rear pancake motor for the Mercury Cougar or Ford Mustang. We completely disassemble these units, then clean and inspect them. Then we will repair or replace minor pieces inside. Please note that if your core is not rebuildable, there will be an extra charge for installing working parts. After the motor is repaired, we...

Air conditioning bearing replacement service. Send your wide bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new wide bearing. Price includes new bearing (long or short shaft) and labor, shipping extra.  * Note * There are several pulleys that we are unable to press apart. Please check photos for examples of the known pulleys that we can assemble, but not disassemble. *NOTE* Excludes certain 1968 pulleys with stamped...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...

Our service is to rebuild your sending unit. A quality core is required. This rebuilt XR7 fuel sending unit has been meticulously gone through and made operational again. All sending units are taken apart and media blasted. Once cleaned, the thermistor is carefully removed from the tube and opened up so that the mesh screen and insulator can be chemically cleaned. All wire leads are removed and tested, then resoldered to their contact points. Upon reassembly, initial testing is done with VOM....

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...

Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. Your core must be complete and not overly corroded. We are unable to convert from non-low fuel to low fuel. We also cannot change plugs for different years. We do not repair rust or rust through holes. We do not have critical or specific spare parts for rebuilding....

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Be aware that the OEM Ford 1967 sending units had 5/16 inch tubes for the filter, 1968 had 3/8 inch tubes.Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980...

This option requires that you pay a $65 core charge.  Be aware that the OEM Ford 1968 sending units had 3/8 inch tubes for the filter, 1967 had 5/16 inch tubes. Our service is to rebuild your standard fuel sending unit. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality core must be complete and not overly corroded. We are unable to...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

Basic kit for rebuilding a 1967-70 Holley model 4150 4 barrel carburetor. Includes illustrated instructions. Holley packaged renew kit. This kit is not for model 4160 or other Holley carburetors. See pictures of Holley 4150 below. Click on images to enlarge. ...

One year only beam that is very prone to rust due to the fact that they were not painted from the factory. Mercury master part number D3WY-17A792-A, also called the front bumper reinforcement beam.

NOS relay for 1967 Mercury Cougar or Ford Mustang with factory speed control. This is the anti retard relay, identified with the plug with two male connectors. Mounts to the Regulator mounting bracket along with the Brake Release Relay. May also be correct for 1968, we are not sure. Ford part numbers C7WA-9C733-A and C7WY-9C733-A.

Referred to as the "K10" relay in the Ford Service manual. The emergency relay, when energized, maintains through circuits from the motor and cam assembly to the rear lamps. During emergency flasher operation, this relay opens the circuits (normal position) to the inner and outer rear signal lamps. Thus, only the center rear lamps operate when the emergency flasher system is functioning. This unit was originally mounted to the underside of the black cardboard trunk filler board on the driver...

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

Identified with the straight bracket compared to the 1968 relay which has a bend. These relays are tested by our electrical department. Keep in mind we have a reproduction substitution for this part. Ford part # C7ZA-3E553-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. This icon means that we're looking to buy this part!WCCC...

Used tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight. These relays are tested by our electrical department. Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.*NOTE* For tilt column service, you can contact...

This is referred to as the "K5" relay in the Ford service manual. This relay causes the flashing action of the 1968 Mercury Cougar instrument panel indicator lights. The number stamped on this relay is C8WB-13A366-A or C8WB-13A366-C, the Ford part number is C8WY-13A366-A or C8WY-13A366-C. Stay tuned for an upcoming electronic version of the 1968 K7 relay.*Caution - Do not use the 1967 relay in place of the 1968 relay, smoke and fireworks will be the result.

This is referred to as the "K7" relay in the Ford service manual. This relay causes the flashing action of the 1967 Mercury Cougar instrument panel indicator lights. The number stamped on this relay is C7WB-13A366-A, the Ford part number is C7WY-13A366-C. A quick bench testing: There needs to be continuity between the 'H' post NOS item, new old stock.       *CAUTION* The 1967 and 1968 K7 relay look similar, but are not the same. Damage to your wiring system will occur...

At last, there's a solution to a problem that almost all early Cougars suffer from. If the turn signal indicators in your dash only blink once, and then pulsate slowly without going out, you need this new electronic relay. It's a direct plug-and-play replacement, and it will give your indicators a nice on-off flash, complete with a mechanical click sound, all in time with your turn signals. We're excited about this simple fix; it's great to see and hear the indicators working properly. The...

At last, there's a solution to a problem that almost all early Cougars suffer from. If the turn signal indicators in your dash only blink once, and then pulsate slowly without going out, you need this new electronic relay. It's a direct plug-and-play replacement, and it will give your indicators a nice on-off flash, complete with a mechanical click sound, all in time with your turn signals. We're excited about this simple fix, it's great to see and hear the indicators working properly. The...

1968 Mercury Cougar K-8 and K-9 turn signal relay assembly. K-8 for the passenger side, K-9 for the driver side turn signals. Also is integral to the brake light circuit. Clean used unit that is tested and will be functional. This unit will not be rusty, have internal water damage, May have minor repairs, no cut wires. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. When these relays are not energized,...

This is the stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Stang. This is a very hard part to come by in good shape. Many times body shops will loose this piece while replacing the top. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2" and is a very good copy of the original. Made in America.

Used roll up door for the Standard Mercury Cougar's center console. Finished metal front and flexible rubber back. Includes chrome knob. Different from the 1968 door in that it has the much smaller handle. Ford part # C7ZZ-6506024-A.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The 67-68 Mustang...

Used roof mounted switch that is rather delicate. As you can see from the pictures, the chrome coating has started to peel slightly. 

Good grade A used jack with correct fine threads. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not. Grade A will not have rust or damage.

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A. Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Used (poor condition) weather strip may or may not be in place. Please go to our rubber section to select the new rubber strips...

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Sold separately, please choose between driver or passenger side. Used (poor condition) weather strip may or may not be in place....

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...

Sold as a pair

Are you looking to replace or upgrade your complicated 1968-73 3 Point Seat Belts with a modern easy to use factory looking Belt?  These 3 Point Seat Belts will bolt onto any 1968-73 Coupe using your existing mounting hardware. . The belt buckles are very similar to the original starburst buckles Ford used in the Late 1960's

Are you looking to replace or upgrade your complicated 1971-73 3 Point Seat Belts with a modern easy to use factory looking Belt? These 3 Point Seat Belts will bolt onto any 1971-73 Coupe using your existing mounting hardware. . The belt buckles are very similar to the original starburst buckles Ford used in the Late 1960's

Are you looking to replace or upgrade your complicated 1968-73 3 Point Seat Belts with a modern easy to use factory looking Belt?  These 3 Point Seat Belts will bolt onto any 1968-73 Coupe using your existing mounting hardware. . The belt buckles are very similar to the original starburst buckles Ford used in the Late 1960's

This is an example of the best set we can come up with. This is a standard set that has the black buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below.  ...

American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process.NOTE: These foam kits work well on the Standard and Decor interiors but you will find on the XR7 the lower portion does not work well.

Used on 1969 Mustang Mach I and Eliminator and all 1970 Mustangs and Cougars. American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process. Upper and lower cushion for one seat. Click on images to enlarge. ...

This Mustang combination foam kit consists of a 1966 Mustang Pony Interior upper and a 1967 Mustang standard lower portion. If you use this set of foam you will have to build the upper portion about 1" all over to get a good fit.  Here is a link to some good advice on the matter.  One kit consists of two parts, enough to do one seat.  This can also be used on the 1967 Cougar bench seat.  This is not an exact fit but of all the foam available it is the combination that...

Reproduction premium seat foam custom made specifically for the standard 1967 Mercury Cougar. Unlike the previous version we carried in the past, this premium seat foam does not require any modification to make fit. One set is top and bottom foam, enough to do one seat. NOTE: This seat foam is also used on the front bench seat.