All Products

Shock tower coil spring cover installation hardware that fits Cougar and Mustang coupe, fastback and convertible.

Used quarter window shoulder screw and nut for the 71 - 73 Cougar and Mustang.

These pads go between the rear quarter panel and quarter panel reflector on the 1968 Mercury Cougar only. Sold as a pair.  Replaces Ford part #: C8WY-13493.*Note - These were not installed on Ford Mustangs, but they could be installed since they use the same reflector after Feb 15, 1968.

Replaces Ford part #C8WY-15447. Sold as a pair, two required per car. Right is the same as left.

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Slat or pivot bracket for attaching the #4 rear most bow on a 1969-70 convertible top. Sold individually, one for each side needed for installation. Bushing is normally broken or missing, plan on sourcing or making a replacement bushing for the pivot. Ford part number C9ZZ-7650340-A.

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

Reproduction hardware kit for installing the smog pump on cars with 390 / 427 / 428CJ engines from 1968-70. Including Cougar, Mustang, Torino, Ranchero, Cyclone, etc. Includes spacer, pivot bolt and washer, adjusting bracket bolts.

Used snap in socket / pigtail for the clock light on your 67 - 68 Cougar. Also fits many other applications.

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Replacement pair of Clutch Equalizer Bar ( Z-Bar) Bushings. These are for manual transmission equipped models and are a bushing that is no longer available from Ford. These are the split bushing style that replace Ford part number C5AZ-7543-C. These fit 1965 1966 1967 1968 1969 1970 1971 Ford Galaxie and Full Size Models (Galaxie, XL, LTD, Custom 500 etc..), 1970 Torino 429 Models, 1971 1972 1973 Mustang, 1972 1973 1974 1975 1976 Ford Torino, Gran Torino and Ranchero models and 1973...

Used under dash wiring harness repair plug and pigtail to the ignition switch light socket for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the dash mounted courtesy light on the Mercury Cougar. The socket is the same on both sides. This is part of the 14401 main under dash wiring harness.

Fuel tank spacer. Welds to the bottom side of the trunk pan. Spaces the tank, so that the fuel vapor separator assembly, isn't pinched. Easy to make these stands, and there are two needed, are approximately 1-1/2 inches tall. Strap is 1-1/8 inches wide.  

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Reproduction  Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...

10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.

3 1/8" Style Steel Wheel Spare Tire Hold Down. Available in Black or Chrome. Ford Master Parts Catalog indicates that this hold down was found on some 68 and 69 Cougars with SS Wheels. You may need to bend the ears in slightly to get them to fit properly inside the hole in the center of the wheel. Replaces Ford Part #: C8MY-1424-A.

Reproduction spare tire hold down kit for the 1967 Mercury Cougar or 1965 - 1967 Ford Mustang. Included in the kit are the wing nut, hold down disc and the J bolt. Exact reproductions of the originals. Check out the very first Cougar in our video below! ...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Unlike previous reproductions this has the correct grommet that passes through the firewall. 68 inches long replacement speedometer cable. New picture coming soon. Fits both C-4 and C-6 automatic transmissions for 1967-68 Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7ZZ-17260-A.

Unlike previous reproductions this has the correct grommet that passes through the firewall.  Replaces Ford Part #: C9ZZ-17260-A.  This cable measures 58 1/2" at its very most outer ends.

Good quality, does have the built in rubber grommet that seals the cable as it passes through the firewall.

Used clip with bolt for attaching the speedometer cable to the transmission of the Mercury Cougar or Ford Mustang. This unit holds the gear end into both automatic and manual transmissions. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Used driver side (left hand) front fender to bumper slash shield for the Mercury Cougar. This is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This will look better than the reproductions, in our opinion, and will cost you less...

Used passenger side (right hand) front fender to bumper slash shield for the Mercury Cougar. This is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This will look better than the reproductions, in our opinion, and will cost you less money....

This driver side (left hand) rear quarter to bumper splash shield is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that it may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This looks better than the reproductions, in our opinion, and will cost you less money. Ford part # C7WY-6529031-A, and...

This passenger side (right hand) rear quarter to bumper splash shield is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that it may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This looks better than the reproductions, in our opinion, and will cost you less money. Ford part # C7WY-6529030-A, and...

Very close to correct spring finish (dark color) and tension. Above is a comparison to the other reproduction, which does not have the correct finish, is not the correct length, and does not have the correct tension. Replaces Ford Part # : C8ZZ-17119-A *Note* Must be used with the correct mounting bracket. See below. ...

Fits the 1967, 1968, 1969 and 1970 Mercury Cougar with the 390, 427, 428CJ or 428SCJ. These have the correct 20 coil spring, but are 1/8" longer than the Ford Master Parts Catalog calls for. Replaces Ford Part #:C7ZZ-7591-AR.

This attaches to the bracket mounted on the top side of your pedal hanger over to the clutch pedal itself. Replaces Ford Part #: C2AZ-7534-A.

Very heavy duty counter balance spring for all 1969-70 Mercury Cougar door regulators with power windows. Original Ford part number C9WY-6523318-A. Power window regulators only, this spring is quite a bit larger than manual window regulator springs. Application also fits 1972 full sized Ford and Mercury station wagon power tailgate windows.

Coil hood hinge spring, 5-13/32" in overall length, 14 coils, coil diameter 1.899 inches. Sold individually, one per side. Other applications include:  1967-69 Mercury Cougar1967-70 Ford Mustang1965-69 Torino, Fairlane, Ranchero1965-70 Falcon 1965-66 Falcon Ranchero Ford part # C3OZ-16789-A. You can find the hood hinge apron nuts here.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Hood hinge spring for Mercury Cougar and Ford Mustang. Coil spring type with 6-1/4 inches of overall length. Sold individually, one per side. Ford part # D1ZZ-16789-A. *NOTE* Excludes 1971-73 Mustangs with ram air hood option.  

Higher quality and higher tension spring than the spring offered by most Mustang/Cougar parts dealers. Replaces Ford part #: C5ZZ-9737-B or C7ZZ-9737-B

Reproduction Concours Accelerator Return Spring for the 1968 Mercury Cougar / Ford Mustang

This is a tension spring that defaults the steering wheel to up and or tilt away position. The spring in the 1967 Column is not as strong nor as tall as the 1968 or 1969 column spring.Spring Length: 2 5/16" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is a tension spring that defaults the steering wheel to up and or tilt away position. The spring in the 68 - 69 Column is stronger and taller than the 1967 column spring.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

New Old Stock 1967-68 Mercury Cougar and 1966-68 Ford Mustang clutch release fork to equalizer spring. Upper clutch equalizer to firewall, 289 and 302 engines. This unit will also work for 1969-70 Cougar and has the correct spring hook orientation. 66 - 68 Ford specs: 3-1/16" Long 40 Coils 69 - 70 Ford specs: 3-1/8" Long 36 Coils Ford part #: C6ZZ-7591-A.

Fits the 1969 and 1970 Mercury Cougar with the 390GT, 428CJ or 428SCJ. Replaces Ford Part #: C9ZZ-7523-B.

Fits the 1969 and 1970 Mercury Cougar with the 302, Boss 302, 351 Cleveland or the 351 Windsor. Stiffer and 1/8" shorter than our other reproduction. Replaces Ford Part #: C9ZZ-7523-A.

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *NOTE* This bracket is a bit shorter than the 4V version.

Used spring cap that is used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.