All Products

Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.

Fan spacer, measuring 2-7/8 inches, sometimes mentioned as 3.15" overall. Applications include 1967-68 Mercury Cougar and Ford Mustang with 289/302 and standard cooling. Reference number YA-79.Ford part # C5OE-8546-A, Ford engineering # C5OZ-8546-A.

Fan spacer, measuring 2-9/16 inches or sometimes mentioned as 2.95". Application includes 1968 Mercury Cougar and Ford Mustang with 289/302 engines and air conditioning. Additionally listed as 1969 Boss 302. Reference number YA-27, same as part # D2AE-8546-A.Ford part # C8ZE-8546-D, Ford engineering # C8ZZ-8546-B.

Fan spacer, measuring 3-1/16 inches, sometimes mentioned as 3.40" overall. Applications include 1967 Mercury Cougar and Ford Mustang with 289-4V. Reference number YA-78.Ford part # C5AE-8546-B, Ford engineering # C5AZ-8546-B.

Reproduction alternator mounting kit for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Spacer not included, but available.

Bolts, washers, and spacers kit for installing the rear bumper brackets on any 1969-70 Mercury Cougar or Ford Mustang.

Sold as a Kit as Pictured.

Reproduction Fastener Kit - Deck / Trunk Lid & Hinges for the 1968 Mercury Cougar / 1968 Ford Mustang 

Fits Standard and XR7 Sold as a Kit as Pictured.

Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang

Fits Standard and XR7

Fits Standard and XR7 with front bumper guards.

Reproduction grille mounting kit for the driver (left hand) and passenger (right hand) sides of the Mercury Cougar.

These reproduction hood and hinge bolts and U nuts fir both the Standard and XR7.

Fits 1967 and 1968 Standard or XR7

This reproduction quarter panel extension fastener kit fits both the Standard and XR7.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits 1967 Standard and XR7

Fits Standard and XR7

A collection of reprinted material originally used by Mercury salesmen in the dealerships. Includes facts, specs, options, some door tags, and much more!

This is our used driver side (left hand) upper rear fender brace for you beloved Cat. Bolts to the cowl on 1967-68 Mercury Cougar and Ford Mustang. Ford part number C7ZB-16A005-A driver side, C7ZB-16A006-A passenger side.

Used passenger side (right hand) upper rear fender brace that brace visible when you open the door and look in the upper part of the fender void. Bolts to the cowl on 1967-68 Mercury Cougar and Ford Mustang. Ford part number C7ZB-16A006-A passenger side, C7ZB-16A005-A driver side.

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

Reproduction black 3D printed brake booster filter retainer for the Mercury Cougar and Ford Mustang. Same functionality at the originals, it fits between the brake booster and master cylinder in the aluminum master cylinder spacer. You can find the filter here.

Reproduction black 3D printed brake booster filter retainer for the Mercury Cougar and Ford Mustang. Same functionality at the originals, it fits between the brake booster and master cylinder in the aluminum master cylinder spacer. You can find the filter here.

NOS air cleaner breather element filters for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, cartridge holder not included.Packaging may vary

Oil filter adapter for all Ford small block engines including 221, 260, 289, 289HiPo, 302, and 351W engines. Ford indicates that this was used 1962-1970. Screws into the engine block. We do not know the threads, but the small side is standard oil filter sized.Ford part number C2OZ-6882-C.

All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...

Reproduction flexible duct end that was originally stapled to the passenger side fresh air duct, found behind the passenger side dash panel of all 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1ZA-18C305-AB.

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

NOS pamphlet from the Ford Motor Company detailing the 24 month 24,000 mile, or 5 year 50,000 mile warranties for the line of 1967 Cars and light trucks including Falcon, Mustang, Cougar, Ranchero, Fairlane, Thunderbird, Bronco, Light Trucks, Comet, Continental and Econoline.Volume 67C16L6

Brass and steel freeze plug or expansion plug set for any Ford 429 / 460 / 429CJ engine. 1971 Mercury Cougar and 1971 Ford Mustang. 13 piece set with threaded screw in plugs as shown. 

Great for that missing or rusted ashtray in the front of your console. Nice snug fit and correct hole for light. Replaces Ford Part #: C9ZZ-6504788.

Reproduction Front Bumper Guard Bolts & J Nuts for the 1967 - 1968 Mercury Cougar 

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, sold individually. Replaces Ford part #: C5ZZ-13207-B.

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, sold individually. Replaces Ford part # C5ZZ-13206-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, Sold as a pair. Replaces Ford part #: C5ZZ-13206-B and C5ZZ-13207-B.

Reproduction Front Valance Bolts & U Nuts for the 1968 Mercury Cougar 

Reproduction ribbed aluminum foil backing plate for the gas doors on the 1969 and 1970 Mercury Cougar and XR7 models.

Used gas door with hinge spring. The black painted door as shown in the picture is a service replacement fuel door. Used doors are bare steel and will come with the hinge and spring.  Ford part number C9WY-65405A26-A

This filter ONLY fits the following Ford Holley 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. This is a service replacement filter, it has D2AE-9155-AA stamped on the body of the filter. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19 and C9AZ-9155-B,  FG-39.

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C5ZZ-9327-A.

This is the OE steel tubing the goes from the fuel pump to the carburetor.

Reproduction fuel line for the Boss 302 engine standard steel construction. Application would be Mercury Cougar Eliminator and Ford Mustang with engine code G or the 302 HO engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

Reproduction fuel line for the Boss 429 engine standard steel construction. Application would be for all Ford and Mercury products with Z code Boss 429 engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

Used original wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Ford Part #: C5ZZ-8287-A.