Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8
Fits 1967 and 1968 Standard or XR7
Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.
Fits 1967 and 1968 Standard or XR7. This kit is nothing more than common door panel clips instead of the correct, unique 1967 A pillar pad clips or 68 A pillar pad clips . These can be made to 'work', but we highly recommend ordering the correct used clips.For the Correct 1967 A pillar pad clips, click here.For the Correct 1968 A pillar pad clips, click here. ...
Bumper that helps stop the 'clunk' noise when you take your foot off of the clutch pedal on manual transmission 67 - 68 Cougars and Mustangs.Replaces Ford Part Number: C7ZZ-7583
Replaces Ford Part # : D0OZ-7583
These reproduction pads are high quality replacements for worn or missing original pads. Replaces Ford part number C9ZZ-7A624-A.
This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.
These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.
Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.
Fits 1968 - 1973 Standard or XR7
Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.
Replica of the coil spring shipping tag that would have been found on factory delivered 1967 - 1973 Cougars and Mustangs.
Reproduction Console Ashtray Bumper for the 1967 Mercury Cougar or Ford Mustang.
The picture above shows these bumpers installed in the 100% correct reproduction console that we sell. These are sold individually, 2 required per car. Replaces Ford part # 379919.
New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.
The decal I most often see on the 1971-1973 Cougar is the used one pictured here. Will be trying to locate this decal soon.
Reproduction Convertible Top Utica Plant Decal for the 1970 - 1973 Mercury Cougar or Ford Mustang
Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.
Replaces Ford part #C1SZ-13783. Replaces burnt, cracked or missing original lenses located above the rear package tray. Two required per car, sold individually.
This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.
Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.
Sold individually Zinc Dichromate (yellow-rainbow)
CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.
Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.
This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.
This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash.
These studs and nuts are used to repair the passenger side mounting studs. The studs need to be drilled out using a 1/4" drill bit. Once done, use a 2 part epoxy and install the stud. Make sure to avoid getting epoxy on the threads where the nut will be installed. Once dry, install the bezel into the dash and use a 3/8 # deep well socket to install the nut. CAUTION: Only tighten finger tight to avoid cracking or breaking the bezel.
Used metal dash support brace for all 1967-68 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 8-1/2 inches long. Viewed in the 1967 Osborn Body Assembly Manual on page 23. Replaces Ford part numbers C7ZB-6504672 or C7ZZ-6504672-A.
Used metal dash support brace for all 1971-73 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 10 inches long. Replaces Ford part numbers D1ZB-6504672-A.
There are five of these on the RH side that hold your plastic dash to the metal understructure. These also hold on the map light. Sold Individually. Ford Part #: 376642-S. Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting things...
Reproduction engine code decal for the 1967 - 1968 Cougar or Mustang equipped with the 289 2 barrell engine with manual transmission.
Reproduction 351 4V AT / MT Emission (Before 1-73) for the 1973 Mercury Cougar / Ford Mustang
Reproduction 351 4V MT Emission (After 1-1-73) for the 1973 Mercury cougar / Ford Mustang
Engine code decal for the 351 with a 2 barrel carburetor and air conditioning.Stamped with engine code K604CG.
Reproduction engine code decal for the 1967 - 1968 S code - 390-4V or 390GT with automatic transmission, Cougar or Ford Mustang.
Reproduction engine code decal for the 1967 - 1968 S code - 390-4V or 390GT with manual transmission, Cougar or Ford Mustang.
Reproduction engine code for the 1968 Mercury Cougar equipped with the 390-4V and manual transmission.
Reproduction engine code decal for the 1968 Mercury Cougar equipped with the 427 engine and automatic transmission. This decal is located on the front of the driver side valve cover.
Reproduction engine code for the 1968 Mercury Cougar equipped with the Cobra Jet engine.
Engine code decal for the 429 Cobra Jet without air conditioning. Decal text: L 10° K833 K
Engine code decal for the 429 Cobra Jet with air conditioning. Decal text: L 10° K833 KG
A/C compressor clutch decal for Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7AA-2987-D.
Replaces Ford Part #: C7ZZ-19959-A.
Here is another great product form Permatex. This decal and adhesive remover removes bumper and window stickers, tar, sap, bugs and other gooey substances.
This is a reproduction of the original orange engine displacement decal with black lettering and black and white checkerboard on each end that was located on the top of the air cleaner.Fits the following models with a 289 High Performance engine:1967 Mercury Cougar1967 Ford MustangThe 289 Hi-Pro motor was never offered in the Cougar as an option but you could order an over the counter unit. ...
This is a reproduction of the original orange engine displacement decal with black lettering that was located on the top of the air cleaner.Fits the following models with a 289 2 barrel engine:1967 Mercury Cougar1967 Ford Mustang
This is a reproduction of the original engine displacement decal. Black with a chrome background followed by black background with a chrome Mercury head and lettering 302- 2V. located on the top of the air cleaner.Fits a the following model with a 302 2 barrel engine:1968 Mercury Cougar