All Products

Used in all of 1970 and the early part of 1971. This collar uses the 'small' access plate cover. Ford master part number D0AZ-3D505-A, casting number on the part is D0AA-3D505. Nice condition, no cracks or damage. Also fits 1970-71 Lincoln MKIII and Thunderbird.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

One year only part not found on any other car except Cougar and Mustang with tilt. If you would like to run a 1968 or newer steering wheel on your 1967 then you need to exchange this cover with the version found on the 1967 Thunderbird which has no lip at the top. We have these in stock and would enthusiastically trade it for the Cougar / Mustang upper cover. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This Thunderbird collar is a good substitute for those wanting to put an after-market or 1968 up steering wheel on their 1967 Cougar / Mustang. We also suggest purchasing this collar when installing our reproduction 1967 Mustang deluxe steering wheel.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used upper steering column cover for the Mercury Cougar or Ford Mustang equipped with the tilt/tilt away steering column. This unit comes naked with no attaching parts or fasteners.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. WCCC no longer has an in-house service for tilt and tilt-tilt away steering columns 1967-1979. After 2...

This complete four piece kit is for any small block 289, 302, or 351 Windsor Cougar 1967, 1968 and 1969. 

This complete four part kit is correct for any 1967-68 small block 289 or 302, and 351 Windsor Mercury Cougar or Ford anything 1967, 1968 and 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut.If you do not have a air conditioning you will need a spacer in place of the round spacer shown. If you have the 351 Windsor without A/C, you will need a the rectangular spacer which is sold separately.

This complete four part kit is correct for any 1969 small block 351 Windsor Mercury Cougar or Ford anything 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut. If you do not have a air conditioning you will need a the rectangular spacer which is sold separately.

Mini console assembly, comes with ashtray receptacle, wiring and socket, and console with a casting number of D1ZB-65045B72-A. Used for automatic or manual transmissions. These came color keyed to your interior, add your desired color in the comments section of your online order. We will try to accommodate color requests where possible. We will select and ship what is available, these are easy to detail with the various vinyl paints available. These are used, and often the ashtrays will need...

This is a used windshield wiper delay governor, or module, and is a black box that mounts under the dash to the left of the radio. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper switch.Part # D1ZB-17C476, D2ZB-17C476, MPC # D1ZZ-17C476-A.

Galvanized three piece replacement tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Reproduction stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. Ford part number: C9ZZ-7654676-A

This is an inexpensive top that is only recommended if you car is going to be stored indoors. Have you ever wondered how a convertible top is installed, or maybe considered trying it yourself? Check out our in-depth installation video below! ...

Replaces Ford Part #: D1ZZ-7650509-A

Replaces Ford Part #: D1ZZ-7650508-A

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

C8SE-B Applications: 1. 1968 289-2V engines with air conditioning or the extra cooling package. 2. 1969 Boss 302 Eliminator - after 4/14/1969. 3. *1970 Boss 302 Eliminator. 4. *1970 351 with or without air conditioning. Fan description - 5 blades and 17-5/8 inches in diameter. Ford master part number C8SZ-8600-B. Multiple dates available. *Note - 1970 Boss2 and 1970 351 owners, some time soon after the start of the year the exact same fan, but with casting number D0ZE-B was used. Check out...

C6OE-G Clutch style 7 blade cooling fan for all 1967 Cougars with 289 engines with factory installed air conditioning. Additionally, 1968 302 engines with factory air conditioning (Cougar and Shelby GT-350 only). Fan description - 7 blades and 17-1/2 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C4OZ-8600-D. Original fan drive clutch cast number for this application is C7ZE-B. NOTE! If you have the fan shown here and would like to upgrade to our FE / Big...

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar produced in 1967 through early 1968 that came equipped with the C-6 automatic transmission and 390 engine. These lines are sold in pairs.

Reproduction transmission cooling line made of stainless steel for the Mercury Cougar produced from late 1968 through 1970 that came equipped with the C-6 automatic transmission. These lines are also available in OE steel and are sold in pairs.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 351W and FMX transmission. These are sold in pairs

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar equipped with the FMX automatic transmission and 351W engine. These lines are sold in pairs.

This Cougar II 1/25 scale factory sealed model kit was made by the Industro Motive Corp in Troy Michigan. This car was actually introduced in 1964 and was a Shelby Cobra based Ford- Cougar prototype vehicle that never made it into production.    Features: Retractable lightsWorking steeringOpening doorsOperating windowsPressure vent flapTubular frameChrome wire wheels260 cubic inch high performance engine ...

For the Cougar fan who has everything! This is a unique, awesome piece to hang on your wall. Made from laser-cut 18-gauge steel, rusted on the surface for a unique patina. Features a walking cat logo and COUGAR lettering. Measures 24" wide by 13" tall.We can also customize your sign for an extra $50 - such as your last name, business name, Joe's Garage, or whatever you'd like in lieu of "COUGAR", as long as we can make it fit (20 characters or less). Mention it in the order comments and we'll...

These lights feature beautiful chrome bezels and bright white lenses. Mounting hardware, bulbs and sockets with pigtails are included. These were used on the XR7 and all Cougars equipped with Decor level interiors in 1969 and 1970. These are AWESOME reproductions worthy of the most exacting of restorations. You will be VERY happy with these lights. Sold as a pair. Replaces Ford Part #: C9WY-13776-A & C9WY-13777-AThese use a 212 bulb.Click on images to enlarge. ...

New Old Stock Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. These are available in reproduction. Nice Quality!Ford part number C9WY-13777-A. These use a 212 bulb.

Rechromed Bezel for your door courtesy lights found on all 67-68 Cougars except the 1968 Standard model. These will require some patience with a dremel tool to remove the lenses from your cores and place them in these. Passenger and driver are the same, keep in mind the red lens goes to the back of the bezel. To be eligible for core refund, your cores can only show light pitting. ...

Access cover, unique to tilt steering columns. This is the little cover on the left side by the turn signal lever. We only find these occasionally as 'spares'. In most cases it will need to be painted to match your steering column color. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Get ready for some serious labor if your car needs this complete panel!

Reproduction cowl center panel for Mercury Cougar and Ford Mustang.

New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD. 

Reproduction Crossmember / Under Engine for the 1971 - 1973 Mercury Cougar / 1971 - 1973 Ford Mustang 

This listing is for a pair of walking cat die cast chrome cufflinks. These would be great for the serious collector who may want to add a bit of Cougar flair to outfit when hitting the town, or simply just another bit of memorabilia to add to their collection.  Walking Cat measures 1-3/16" across.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom made Walking Cat belt buckle for the Cougar die hard. This would make a great gift for anyone who lives and breathes everything Cougar. The buckle is bare, unpainted and ready for you to customize how you see fit. We're not sure how we ended up with this awesome collectable, but it's definitely one of a kind and the only one we know of, so when it's gone it's gone!  Measures 3 3/8" x 2 1/4"

Single cylinder head from 1968 Mercury Cougar 302-4V engines without smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 52-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C8OE-D and "302" and "4-V".Current casting dates include: 7G25,...

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...

Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....

Used highly collectible Dan Gurney slot car racing track made by the Republic Tool and Manufacturing Corporation in Los Angeles California. Open box and lightly used. Both cars are intact, and the decals have been placed on the the vehicles and the track. Everything is good condition, but the cars have not been tested and the red car has had it's wheels painted. Other than that, this is a rare and truly great find. Features the Mercury Cougar Logo on front of the box.

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider installing your dash...

Used aluminum face pad moulding / trim four piece set for the Mercury Cougar.

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent as shown here. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider...

You can receive up to $95 credit when you send in your AC center panel in exchange for this non AC center panel. We will also carefully match our stock against yours to ensure you have a good color match against your right and left panels. Please call 503-463-1130 for details. Check out our video on dash removal and restoration: ...