All Products

Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs equipped with the 429CJ engine.  Listed in the Master Parts Catalog (MPC) as # D0AZ-2882-A. Replaces part #  D0AA-2882-B.

This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.

Reproduction thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Painted Ford engine blue a shown. Nice reproduction, made in the USAFord part # C8AE-9C486-A.

Thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Ford part # C8AE-9C486-A. *RESTORATION TIP* This bracket was painted Ford Engine blue from the factory.

Used mounting bracket for the sunroof motor on the 67 - 70 Mercury Cougar. This bracket is only used with the 67 - 70 power sunroof motor.

Bracket that mounts to the rear Carburetor mounting holes of all 1969 351-4V and 428 Cobra Jets or Super Cobra Jets. Has the square hole that holds the factory throttle cable and hole for the return spring.  Replaces Ford part number C9ZZ-9741-B. *Note - This is not a flat bracket like the 1970 351C-4V. There is a distinct drop in the bracket to clear the underside of the Holley carburetor on Cobra Jet equipped cars This is the original factory bracket, reproduction brackets have...

Used with factory "Autolite" carburetor and aluminum carburetor spacer unique to the 1969 Cougar. Bracket that mounts to the rear Carburetor mounting holes of all 1969 390-4V. Has the square hole that holds the factory throttle cable and hole for the return spring. Has a distinct dip or curve, midway between the mounting holes for the carburetor.Replaces Ford part number C9ZZ-9741-C.

If your Cougar came from a region that uses road salt your buckets are probably rusted in the corners or worse. Our dry "West Coast" buckets are 100% rust free and the mounting tabs are not broken from the removal of stubborn bolts. They will not be bent or damaged in any way. Keep in mind we do have grade B brackets for much less that only have minor bends or blems that could be easily corrected. *NOTE* These parts are far more important than most people realize. If they structural integrity...

These driver quality buckets are solid but will have a small bend, hairline crack or the beginnings of rust in a corner. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in these brackets are very powerful and if these brackets do...

These driver quality passenger side headlight buckets are mostly solid but will have a small bend, hairline crack or the beginnings of rust in the corner closest to the battery. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in...

This kit includes all new hardware, and both brackets. Mounting diagram not included (you can save and print the photo above). As shown, 1967 - 1968 rear bumper guards mount 17.5" from the center line of the car. Clip and bolt hardware kit will be new pieces.

Correct looking mounting plates used to mount the 1970 original spoilers. Comes with all hardware shown, not intended for 1969 spoilers as the use of these requires large rectangular holes, found only on 1970 of the bottom side of the deck lid.

Chromed engine oil dipstick as found on many 1967-69 Ford with 390 engines (S Code), 427-4V (W Code), 428CJ (Q or R Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end varys at either 19.25" and approximately 20.25" (full, add, and safe marks are the same). The handles were chromed originally. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

This is by far the best, most correct FE pan ever offered. Very accurate reproduction of the C6OZ-6675-A oil pan used first on the 1966 Fairlane and Comet with one of the 390 CI optional engines. It is 100% correct for 1968 and early 1969 428CJ. It is not 100% correct for the 428SCJ but still a good alternative.

Reproduction oil pressure remote sending unit tube assembly mounting kit.. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge. The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell...

Early production brake lines were routed 'over' the steering column.

Early production brake lines were routed 'over' the steering column.

Late production brake lines were routed under the steering column.

Bare outer tube for the 1967 Cougar or Mustang tilt steering column. This item will be free of major rusting and will have to be painted to match your car. Keep in mind that these tubes are specific to each year. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out this video ...

Bare outer tube for the 68 Cougar or Mustang tilt steering column. This item will be free of major rust, and will need to be painted to match your car. Keep in mind that these tubes are year specific. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out this video ...

Bare outer tube for the 69 Cougar or Mustang tilt steering columns. This item will be free of major rust, and will have to be painted to match your car. Keep in mind that these tubes are year specific. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out this video ...

This listing is for the outer wheel house on a 1967 or 1968. Often when you replace the skin you will find multiple soft spots in the outer wheel house, especially down low. If you do not want to pay the oversized shipping on these large items we do sell patch panels.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This listing is for the outer wheel house on a 1967 or 1968. Often when you replace the skin you will find multiple soft spots in the outer wheel house, especially down low. If you do not want to pay the oversized shipping on these large items we do sell patch panels.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This listing is for outer wheel house lower patches, front and rear for the driver side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

This listing is for outer wheel house lower patches, front and rear for the passenger side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

New ABS hand cut package tray for the 1971 - 1973 Mercury Cougar Coupe.

Used Grade "A" over-head or roof console pad for any 1967-68 Mercury Cougar XR7. All of these pads will have minimal to no distortion or foam separation as shown in the photos. These came in a variety of colors, so be sure and include your desired color in the comments section of your online order. Other parts available and sold separately.Replaces Ford part number C7WY-65519A92 or C8WY-65519A92.

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part. Note! Road trash of all sorts, sand, gravel, etc. ends up in the gutter to the right hand side of the road. The front tire tends to form a vacuum and sucks stuff away from the...

This reproduction cowl vent repair panel for the passenger side (right hand) of the Mercury Cougar or Ford Mustang addresses a common problem with these old Cats and Ponies. Rust in the cowl. Easy to install on the driver side, but takes more effort on the passenger side, especially if you have air conditioning. These panels are also called fresh air cowl vents or inner cowl vent repair panels. Another way to avoid doing expensive cowl repairs is to purchase our cowl cover.*NOTE* ...

If your core is not adequate we have cores for sale. Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

Front passenger side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your RESTORABLE cores. Do you have questions about your cores trim pieces? This video should help! ...

This purchase requires you send a good core in advance. If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by...

Rear passenger side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your RESTORABLE cores.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 67 did NOT have the cutout for the side marker light and the 68 did.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 68 has the cutout for the side marker light and the 76 does not.

This used driver (left hand) side lower front fender patch panel is rust free with no prior damage. Cut with a plasma cutter, removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 69 has the small side marker light, and the 70 has the bigger, recessed side marker light. ...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 67 does NOT have a cutout for the side marker light like the 68 has.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 68 has the cutout for the side marker light, and the 67 does not.

This used passenger (right hand) side front lower fender patch panel is rust free with no prior damage. Cut with a plasma cutter and removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 69 has the smaller side marker light and the 70 has the bigger, recessed marker light. ...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.