All Products

Attaches to the lower front portion of the front fender. Good used brace that may be lightly rusted but not ripped, but will almost always show minor repairs. Fits passenger and driver side. Most often they will have the J-nut still installed on both ends.Ford master part # C9WY-16B134-A.

Good used Western part that is not bent or heavily rusted and the left is the same as right. Ford master part # D1WY-16B134-A.

Looped weld in retainer for the rear seat installation on any 1967-70 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets. We think that the Ford number is C5AZ-6263370-B, but we have not been able to verify this for certain. For sure that basic Ford part number is 63370. ...

Hook bracket weld in retainer for the rear seat installation on any 1971-73 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. Sold individually, two required per car. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets.  The Ford number is C9AZ-6263370-A.

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged.  Check out our video "All about seat belts" below. ...

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

For power or manual drum brake Cougars. Late production brake lines were routed under the steering column.

72 - 73 Mercury Cougar and Ford Mustang Front Drum Intermediate Brake Line made of OE-style steel. Intermediate Brake Lines are the lines running from the front of the car to the back feeding your rear brakes. These lines will run along your chassis all the way back to the rear brake drop hose. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. ...

For power or manual drum brake Cougars.Early production brake lines were routed 'over' the steering column.

Early production brake lines were routed 'over' the steering column.

***WARNING*** Plugging these directly into a Cougar wiring harness without correctly re-wiring in the pigtails may fry your wiring harness! Reproduction driver side (left hand) and passenger side (right hand) front turn signal / parking light assemblies for the Ford Mustang. The plug is not correct for the Mercury Cougar's wiring harness and will need to be changed to work properly. However, this is an easy straightforward process which we lay out below. Plus you can save a good amount of that...

D0WY-9A091-A Front evaporative vapor separator, mounts in the drivers side trunk well. *Note - This is only a small part of the 9B004 assembly.

Reproduction brake line clamp kit for the Mercury Cougar or Ford Mustang.

Used factory installed vented fuel, or gas cap as installed on 1967-69 Mercury Cougar 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap.We stock these in limited quantities, and will have an intact paper gasket. Correct "VENTED" embossed and has the "S" stamped onto the center rivet. Price is established by demand, and these normally are only needed for very high level restorations or strict concours judging...

Good used fuel door framed insert, without the crest as shown. These in most cases will not include the thin foil backing plate as shown. "A" grade will have minor rust pitting and some dullness on the chrome, overall very good used.Foil backing plate available in reproduction, see related items.

Fair used fuel door framed insert, without the crest. These most often will not include the thin foil backing plate as shown. "B" grade will have some rust pitting and some dullness on the bright work, overall fair used. Foil inserts available used in limited quantities.

New Old Stock gas door. Fits all 1969-70 Mercury Cougars. Ford part number C9WY-65405A26-A

This is the steel tube that goes from the carburetor to the fuel pump. Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps.

Reproduction OE steel one piece fuel pump return line with 5/16" fittings for the Mercury Cougar. *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

This is the steel tube that goes from the carburetor to the fuel pump on the 289 or 302 with the AutoLite 4300 4 barrel carberator. Original steel version.

This is the steel tube that goes from the carburetor to the fuel pump. OE Steel

This is the steel tube that goes from the carburetor to the fuel pump. Stainless Steel

This is the steel tube that goes from the carburetor to the fuel pump if you have a 289 or 302, and you have the Autolite 4300 4 Barrel Carburetor. Stainless Steel.

This is the steel tube that goes from the carburetor to the fuel pump.

This is the steel tube that goes from the carburetor to the fuel pump.

This is the steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

This is the stainless steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

Reproduction fuel line for the Boss 351 engine. Bent for use with factory intake manifolds, OEM fuel pump, and OEM installed Holley carburetor.Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

This is the steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

This is the steel tube that goes from the carburetor to the fuel pump.

Reproduction STAINLESS STEEL Fuel Pump to Carburetor Fuel Line for the 351W And the 4 BBL for the 1968 -1970 Mercury Cougar

This is the original equipment steel tube that goes from the carburetor to the fuel pump.

Reproduction stainless steel line that runs from the fuel pump to the carburetor on your 68 Cougar or Mustang X Code equipped with a 390 2V engine.

Reproduction fuel line for the 429 Cobra Jet engine standard steel construction. Application would be for all 1970-71 Ford and Mercury products with J or C code 429CJ engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Rochester Quadrajet carburetor.

Reproduction STAINLESS STEEL Fuel Pump to Carburetor 429 CJ 4 V Quadrajet for the 1971 Mercury Cougar or Ford Mustang

Reproduction fuel line for the Boss 302 engine stainless steel construction. Application would be Mercury Cougar Eliminator and Ford Mustang with engine code G or the 302 HO engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

Reproduction OE steel fuel tank to pump two piece fuel line with 5/16" fittings that runs down the rocker panel on the late production Mercury Cougar. *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

This is the steel tube that goes from the carburetor to the fuel pump. Designed for vehicles LO-VOL fuel pump, fits 67 - 70 Mustang, 67 Cougar 390, 67 Fairlane and Torino.

Reproduction OE steel two piece fuel tank to pump with 3/8" fittings for the Mercury Cougar.If you decide to upgrade to larger lines, remember that you have to use 68 fasteners.*NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction OE steel two piece fuel tank to pump fuel lines with 3/8" fittings that runs down the rocker panel on the Mercury Cougar. *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction OE steel tank to pump fuel line for the Mercury Cougar equipped with the 428 Cobra Jet and staggered rear shock. The factory staggered the rear shock to help eliminate axle wrap and wheel hop under hard acceleration.*NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date. ...

Reproduction OE Steel Fuel Vapor Line for the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang with 5/16" Fittings

Reproduction fuel pump for all 1970-73 Mercury Cougars and Ford Mustangs equipped with the 351 Cleveland engine. 

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 390-2V or 4V engines. Updated design from the originals, fuel lines fit the same.