All Products

C7ZA-3590-B 1967 - 1968 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B.Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

Power steering pitman arm for any 67-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. Replaces Ford part number C9ZA-3590-A This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Power steering pitman arm for any 1967-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

C7ZA-3590-C 1967 - 1968 Power steering box pitman arm with 1-1/8" inch sector shaft. Ford part number C7ZZ-3590-C.Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

This reproduction pitman arm equipped on 71 - 73 Cougars and Mustangs with factory power steering. Heavy-duty cast construction. Includes a new castle nut, cotter pin and zerk fitting. Replaces Ford part number D1ZZ-3590-B.

This is a good used and tested power harness which goes from the circuit breaker at the starter solenoid to any of the following:1. Heated backlight (rear defroster)2. Power seat3. Seat back release4. Convertible top

Lower pressure hose. High pressure hose from insulator to the control valve. 1967 Mercury Cougar Ford Mustang with S code 390-4V V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only. Please see part number 31890 for the lower section of pressure hose.

C9ZZ-3A719-A Upper pressure hose. High pressure hose from the pump to insulator. 1969 Mercury Cougar and Ford Mustang with H or M code 351 Windsor engines. All correct ribbing, striping, and crimping. Stamped with C9ZA-3A719-B. *Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only. Please see part number PS4U2 for the lower section of pressure hose.

C7ZA-3A719-B Upper pressure hose. High pressure hose from the pump to insulator. 1967 Mercury Cougar Ford Mustang with S code 390-4V V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only. Please see part number 31891 for the lower section of pressure hose.

High pressure hose from the pump to insulator. All correct ribbing, striping, and crimping.*Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only.Stamped with C9ZA-3A719-A.

D0ZZ-3A719-G Upper pressure hose. High pressure hose from the pump to insulator. 1970 Mercury Cougar Ford Mustang with Boss 302 or 351 V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. Stamped with D0ZA-3A719-D. *Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only. Please see the various part numbers for the lower section of pressure hose.

Pair of correct power steering hoses for your 67-69 Cougar or Mustang. All correct ribbing, striping, and crimping. Hoses have 5/16" fittings. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder. Part numbers: C60A-3A717-A C60A-3A714-A

Reproduction multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Does not include dipstick. Manufacurers note: In place of the paper gaskets, it is recommended that you use gray atv...

Up for grabs is something special for the serious collector of everything Cougar. This is an official press release document with attached 8x10 glossy photo of the 1970 Houndstooth Cougar. These were prepared by the Lincoln Mercury Public Relations Department for immediate release to newspapers in order to spread the word about new and exciting announcements. This particular release features a glossy black and white photo of a woman dressed in a "Swashbuckling Houndstooth Cape" inspired...

Ford part number C9WF-10C956 Correct only for 1969 Eliminator and XR7 models built prior to 2/17/69. After 2/17/69 and all of the 1970 model year uses a red board. No burns or breaks. This is an example of the early 1969 XR7 underdash wiring harness connection plug and wires.Check out the video below on our new gauge tester: ...

Finally! A made in the USA reproduction printed circuit board for your 1969 XR7 or Eliminator built before 2/17/69. This is a spot-on, class "A", no excuses reproduction that will give you decades of reliable service. This part exceeds the quality of the originals in that it is made from thicker materials, is bonded better, is more flexible and does not contain formaldehyde as did the originals. This is only for use on the 69 to replace the factory Blue circuit board, if your original PCB is...

Used proportioning valve for the 1967-68 Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. For 1967 Cougars, this valve is most often found at the junction of the high pressure hose back at the rear end. 1968 had it connected to the distribution block on the driver side firewall. Will come with the C7OE-... stamped valve. Starting in 1969 the valves had a C9OE... Ford part number. These are used...

New crank shaft pulley with 2 sheaves for any 3 bolt, 289 / 302 / 351W engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions.   6-3/8" overall diameter, has 3/8 and 1/2 inch grooves for fan belts. Replica of the C7AE-6312-A crankshaft pulley by Ford. Double sheave 67 crank pulley.

C7AZ-6A312-A. Double or two groove crankshaft pulley. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. 6-1/8 inches in diameter. 1967 Application - Mercury or Ford 289 with automatic transmission and standard cooling (17 inch radiators). Without air conditioning and without power steering. 1968 Application - Mercury or Ford 289 or 302 with or without power steering. Thermactor emissions permissible. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. ...

C9OZ-6A312-B. Application 1969 351W engines without air conditioning, and with or without power steering. Ford casting number C9OE-6312-E. Double sheave 69 crank pulley.

Ford part number C8AZ-6A312-C. Application 390-2V and 1968 - 1969 390-4V engines without air conditioning and with power steering. Ford casting number C8AE-6312-C. Double sheave 68 69 crank pulley.

Ford casting number C5TE-6312-A. Single cast iron pulley for use with California thermactor emissions and low mount dual alternator pulleys. No other options, just the DSO 52 and 53 California engines. Ford Master Part number C5TZ-6A312-A. 6-5/8 inches in diameter. Together with the inner crankshaft balancer pulley, these now paired pulleys drive both the water pump and alternator pulleys. The Thermactor air pump pulley is driven by the 3rd outer water pump pulley sheave - only. Must use the...

Single sheave crankshaft pulley. No options, one single fan belt around the crank shaft pulley, water pump pulley, and the alternator. Probably found on Boss 351, and other 351C cars without power steering or air conditioning.Pulley marked D1ZE-6312-AA.

Application 390 engines with only an alternator and water pump. Ford casting number C8AE-6A312-B. Single sheave 68 crank pulley. 

Ford part number C8OZ-6A6312-B. Application 289 and 302 engines with air conditioning and power steering optional. Ford casting number C8OE-6312-B. Triple sheave 68 crank pulley. While this pulley is identified as the available pulley over the Ford counter for this application, the C5AE-B pulley is what was installed on 1968 Cougars and Mustangs from the factory.

D0OE-6312-C For both Cleveland and Windsor 351 engines. This is also the "with air conditioning" pulley, but with power steering option. Triple sheave 8.00", 7-55/64", 6-9/16" diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0OZ-6A312-B. This is a Service Replacement pulley for D0AE-6312-C. *Excludes 1972 Q code 351 Cobra Jet engines. This means all 1972 351C-4V engines.

D2OE-6312-AA Application - Q code 351 Cobra Jets with air conditioning or power steering. Triple sheave pulley, 6-9/16" and 7-13/64" in diameter. Ford Master Parts number D2OZ-6A312-A.

C9ZZ-6A312-B. Application 1969 351W engines with air conditioning. Power steering optional. Ford casting number C9ZE-6312-B. Triple sheave 69 crank pulley.

C9OZ-6A312-E. Application 1969 390 engines with air conditioning, power steering optional. Ford casting number C9OE-6312-C. Triple sheave 69 390IP 390-4V crank pulley.

Casting number C5AE-D. Triple sheave pulley used with both air conditioning and thermactor emissions. Inner pulley fits over the harmonic balancer, largest pulley is 7-3/4 inches in diameter. *Note - with the inclusion of this larger diameter pulley you must use timing pointer part number C5AE-6023-A.

Application 1968 390-2V with air conditioning and without power steering. Ford casting number C8AE-6312-B. Triple sheave crank pulley, small groove 6 1/8" diameter, large grooves 7 1/4" diameter. Replaces Ford part number C8AE-6312-B.

Application 1967 289 engines with air conditioning early cars built prior to 9-11-66. Casting number AA. 5-1/4" diameter and 3/8" sheave width.

Application, 1968 289/302 engines without air conditioning, but with a single alternator belt. 1969 351w engine without air conditioning, but with dual alternator belts. Casting number 7AE. 4-5/8" diameter and 5/16" sheave width.

Applications, 1968 289/302 engines without air conditioning, but with dual alternator belts. 390/427/428CJ engines without air conditioning. Casting number 6AA. 4-21/32" diameter and 7/16" sheave width. *NOTE* This is a good alternative for the hard to find AG pulley.

Application 289/390 engines without air conditioning. Casting number AC 4-7/8" diameter and a 7/16" sheave width.

Application, 351w engine without air conditioning, but with only a single alternator belt. Casting number 7AA. 5-3/16" diameter and 3/8" sheave width.

Application 390 engines without air conditioning but with a dual belt alternator. Casting number AG 4-5/8" diameter and a 7/16" sheave width. This is an increasingly difficult pulley to find these days. A good option is the 6AA pulley. The size difference is less than 1/8" and you cannot visually tell the difference.

Application all 390-4V engines with and without air conditioning. 289-2V and 289-4V all with air conditioning. Pulley diameter is 5.95 inches 1967 smog pulleys are unique in that they have 4 mounting holes. Ford part number C6AZ-9B447-E, engineering number as seen on the front of the pulley is C6AE-9B447-E. *California DSO 52 and DSO 53 only.

C7AZ-8509-E 289/302 Water Pump Pulley-Used C7AZ-8509-E Thermactor emission systems. Application also includes 1969 Boss 302 Eliminator. All applications are without air conditioning. With or without power steering. Triple sheave pulley all equal diameter at 6-7/16 inches. Ford casting number C7OE-8509-B. *1967 application with standard cooling (17 inch radiator) *After 11-13-1966

C6AZ-8509-A For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. Thermactor OK on any application. 2 sheaves with a diameter of 5-7/8 inches. Ford casting number C6AE-8509-A. *For year 1967 only > Notes say Prior to 1/9/1967.

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate.This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel.You can find the...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate.This is a "patch" cut, which means that vertically it reaches from the bottom of the panel to about 10" up.You can find the full versions here. ...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if yourrequirements for a cut are are different from what is shown, and often we can accommodate. This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel. You can find...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if yourrequirements for a cut are are different from what is shown, and often we can accommodate. This is a "patch" cut, which means that vertically it reaches from the bottom of the panel to about 10" up. You can find the full versions...

Used grade "A" quarter window channel / frame for the driver side (left hand) of the Mercury Cougar. This unit is pit free with no visible pits on either side, but the chrome will most likely be discolored from being exposed to the elements for 45 plus years. There is an upper quarter window channel / frame that screws to the lower portion, but it is made from stainless steel and rarely needs replacing. However, if you need one, mention it in the comments and we will throw one in with your...