All Products

Used grade "B" passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years...

This stainless steel driver side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. At this time, it is best to send in your "A" grade cores and have your own moulding / trim pieces restored. Our supply of "A" grade used moulding / trim is very low. After 30 days, core refunds will be given as in store credit that is equal to the core charge amount. Ford part #...

This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. At this time, it is best to send in your "A" grade cores and have your own moulding / trim pieces restored. Our supply of "A" grade used moulding / trim is very low. After 30 days, core refunds will be given as in store credit that is equal to the core charge amount. Ford part #...

This passenger side (right hand) restored drip rail mouldings / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show...

NOS driver side fender trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16075-A. This icon means that we're looking to buy this...

NOS passenger side fender trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16074-A. This icon means that we're looking to buy...

NOS driver side (left hand) fender extension moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear and often the tooling was near the end of its life so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16075-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

New Old Stock NOS lower gas door trim for any 1969-70 Mercury Cougar. Current trim part is NOS out of the box, without fasteners. Ford part number C9WY-65405-A, casting number C9WB-65405A96-A.

C9WY-65405A48-B

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Chrome trim for the upper headlight housing. "L" shaped trim in Grade A used condition, very tough to find in this condition, click the 'notify me' tab for email notification of new available stock. Fits 1973 Mercury Cougar only. Grade A trim will be pit free, but will have some freckling present. Driver side upper trim.Replaces Ford part number D3WB-13B165-AB.

Chrome trim for the upper headlight housing. "L" shaped trim in Grade A used condition, very tough to find in this condition, click the 'notify me' tab for email notification of new available stock. Fits 1973 Mercury Cougar only. Grade A trim will be pit free, but will have some freckling present. Passenger side upper trim.Replaces Ford part number D3WB-13B164-AB.

Here is our used center hood lip moulding / trim in grade "A" condition for your Mercury Cougar. This is a tough little unit to find in NOS form or grade "A" condition. Most of these will come with some very minor freckling in the chrome.Mercury part # D3WY-16958-A, Mercury casting # D3WB-16958-A.

NOS driver side hood trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16857-A. This icon means that we're looking to buy this...

Restored hood lip moulding / trim for the Mercury Cougar. They really do look as good in person as in this photo. Due to the "enclosed" nature of this design, only trim with minor dings can be restored. Ford part # C7WY-16855-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim...

NOS passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. The tooling was often near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16856-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS passenger side hood trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16856-A. This icon means that we're looking to buy this...

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

Used core grade rocker moulding for the driver side (left hand) of any 1971-73 Mercury Cougar. Right is the same as left on the 1971-73 Rocker Mouldings, we suggest you choose between passenger and drivers side when ordering as they are always duller up front from the tires throwing up road debris. They will come with minor dents and or scrapes, but no major dents or extra holes drilled. These are driver or core quality and are good for restoration, not show quality. Ships bare, without...

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

Reproduction driver side (left hand) and passenger side (right hand) pair of quarter window mouldings / trim with used stainless steel mounting brackets attached. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting and or holes being drilled in them due to them coming off. We bond these to the mounting brackets in house with a liberal application of 3M Windo-Weld #08609. The factory...

Reproduction driver side (left hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Reproduction passenger side (right hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Premium reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible. This version is also much more rigid when compared to the economy version and is not so prone to denting by applying too much pressure when installing. Clips sold separately. This premium moulding weighs 10 oz., compared to the economy deck lid moulding at 6 oz., and an original moulding at 7...

Used aluminum rear deck lid moulding / trim for the Mercury Cougar. Our used trunk lid trim is usually dull and lightly scratched as you see pictured here. Expect numerous and heavier scratches in the key hole area. We have a really hard time keeping good, straight used aluminum deck lid mouldings in stock. They are very prone to damage and many have been replaced with the 1969-70 stainless steel version which was the standard service replacement part that Ford would have sold you from 1969...

Used driver side (left hand) lower rocker moulding / trim for the Mercury Cougar. There is a slight difference in the contour on the ends of this piece that differentiates driver and passenger side. These will not work on a 1970 as the rear wheel opening was increased in size for the 1970 model year. These 1969 mouldings are about 79-1/4" long. These almost always have one or two holes drilled in them are dull at the front due to road debris and have multiple small dings and scrapes. Driver...

NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B

NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.

This is the trim piece the goes across the top on the inside of the windshield. This piece will need to be sand blasted and repainted. Many people have chromed these, but from the factory they were painted satin silver.Ford Part #: C9ZZ-7603606-B

This is the "Chrome" trim across the top of the windshield on the inside. This piece will need to be sandblasted and repainted. Many people have chromed these, but because of Federal safety regulations from the factory they were painted satin silver.Ford Part Number: D1ZZ-7603606-A.

This driver side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603599, D1ZB-6503599-aw, D3ZZ-7603599, D3ZB-6503599-aw *NOTE* Excludes...

This passenger side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503598 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603598. *NOTE* Excludes Mustang Fastback and Mach 1 models. ...

This pair of restored drip rail mouldings / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show car. Ford part #...

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot, a slip on the buffer wheel... There are many reasons why we label our restored trim parts as blems. We carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to. From 10-15 feet away these look as good as our premium quality restored parts, but upon closer...

Used anodized aluminum three piece rear moulding / trim set for the Mercury Cougar. Used driver quality set with no obvious dings or deep scratches. Better than our core sets in that they have more luster and less damage. Keep in mind these are off a 40 year old parts car.Ford part #'s: Driver side rear quarter extension trim C7WY-6529313-A, passenger side C7WY-6529314-A, and center trim C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on...

Core four piece rear window moulding / trim set for your Mercury Cougar. These stainless steel mouldings will have light scratches and minor dings and are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part #'s: Driver side upper C7WY-42431-A, driver side lower C7WY-42405-A, passenger side upper C7WY-42430-A, passenger side lower C7WY-42404-A.*NOTE* Keep in mind we buy most...

Used four piece rear window moulding / trim set for your Mercury Cougar. Good used four piece set with no dings or heavy scratches. Ready to install on your Cougar as is or polish them to a mirror like finish to be installed on a show car. These are above average original FoMoCo mouldings and are ready to install as-is. No disappointments. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY. Ford part #'s: Driver side upper C7WY-42431-A, driver...

This original FoMoCo, five piece windshield trim set has been lovingly restored to far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well (except fastback). Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A, C9ZZ-6503148-B,...

This "offshore" set of low quality reproduction windshield mouldings / trim are sold only as a set. You will not want to mix and match these reproduction units with used because the color and quality will not match. These are guaranteed to look bad and fit even worse. No returns, no exchanges. We strongly suggest that you purchase our restored or good used set. And yes, these are the exact same trim parts supplied by the other vendors with a completely different description. Check out our...

*NOTE*   Due to the difficulty in obtaining 69 aluminum trim we no longer sell these without first having you send us your cores.  Keep in mind we pay well for quality 69 hood lip mouldings.  Do not contact us with pretzel shaped parts, parts you have attempted to fix or flattened out parts.  We need trim parts showing only minor dings / dents, scratches and dullness.  Decent used trim part that would look good on a daily driver. This purchase requires that you...

Cast iron construction similar to the 1969 bracket but with a design change for 1970. We suspect that the change was made for the new pulley and bracket arrangement starting in 1970. Ford part number D0ZZ-9B450-B.

Special rear mounting bracket for 1970 Boss 302 Cougar Eliminators and Ford Mustang. Triangular shaped bracket as shown. Ford part number D0ZE-10A336-A.

Bracket mounts to the intake manifold. With square throttle cable mounting hole and return spring mounting hole. 1970 only, bracket that utilized the two raised mounting bosses cast into the cast iron 428 Cobra Jet intake manifolds.

Bracket that holds the throttle cable for the G code Boss 302 Cougar Eliminators. This is a 1970 part number, it is possible that the 1969 bracket may be either different or had a C9ZZ-9741-? part number. Will update when we verify, comments welcome. 1970 Ford part number listed as D0ZZ-9741-A.

Pair of used assembly line installed 1970 Mercury Cougar Eliminator rear spoiler brackets. Brackets only, no fasteners or spacers. Sold as a pair as shown, right and left side brackets. Can only be used with 1970 trunk lids. 1970 trunk lids have a slot cut out on each side for locating the rear wings. Not used on the 1969 Cougar Eliminator.We also stock the reproduction kit which includes fasteners. See in related items.

Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This chromed push on oil cap was used on the DGS package or engine dress up kit which included chrome valve covers and air cleaner lid. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a Black painted version was also available on most 289 engines sold in California. This icon means that we're looking to buy...

Chromed engine oil dipstick as found on all 1970 Mercury Cougar and Ford Mustang with 428CJ engines (Q or R Code). Top of shield to dip stick is 20 inches. The handles were chromed originally. Ford part # D0OZ-6750-C, Ford casting # D0OE-6750-C.*NOTE* This is an improved dipstick that better reflects the actual full mark, from previous 428CJ dipsticks.

Chromed engine oil dipstick as found on all 1971 Mercury Cougar and Ford Mustang with 429CJ engines (C or J Code). Top of the shield to the dip stick is 16.23 inches. The handles were chromed originally. Ford part # D0OZ-6750-B, Ford casting # D0OE-6750-B.*NOTE* This is not the same dipstick as found on garden variety 429 and 460 engines.