All Products

Used grade "B" over head or roof console pad for any 1967-68 Mercury Cougar XR7. All of these pads will have some distortion or foam separation as shown in the photos. These came in a variety of colors, so be sure and include your desired color in the comments section of your online order. Plan on using vinyl paint for improving the color, due to time, and UV light. Color vinyl pad only, other parts available and sold separately.Replaces Ford part number C7WY-65519A92 or C8WY-65519A92. ...

This wheel was used on several FoMoCo products including the Cougar, Ranchero, Torino Elite, LTD II, Thunderbird, Granada and Mercury comet, Monarch. Originally a brushed stainless trim ring was used but they look good with no trim ring as well.

This listing is for the person who only has rust under the corners at the rear and does not want to pay shipping on an entire frame that must ship via truck freight. It will come as shown unless you contact us. We can also cut the section in half if you only need one corner.  The part will be the same price no matter where we cut it, let us know in the comments section where you would like us to cut if you want something other than what is shown. ...

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the driver.

Patch panel for the driver side outer kick panel area of the exterior of the car, hidden by the fender. This panel has the correct drain cutout for water coming down from the cowl.

Patch panel for the passenger side outer kick panel area of the exterior of the car, hidden by the fender. This panel has the correct drain cutout for water coming down from the cowl.

Reproduction patch panel for the wheel lip on the driver side (left hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge.  These panels are made from 20 gauge (.036-.037) steel, typically cut 23" x 13"

Reproduction patch panel for the wheel lip on the passenger side (right hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge.  These panels are made from 20 gauge (.036-.037) steel, typically cut 23" x 13" ...

Reproduction rear floor patch panel for the 67 - 70 Cougar. This is the floor pan directly to the inside of the driver side wheel well, and has the holes for the rear seat belt bolts. Cut in house from a complete reproduction trunk pan. NOTE* If you buy both sides left and right we can leave them as one continuous panel at no extra charge just for the asking, please leave a note on your online order in the comments section. ...

Reproduction rear floor patch panel for the 67 - 70 Cougar. This is the floor pan directly to the inside of the passenger side wheel well, and has the holes for the rear seat belt bolts. Cut in house from a complete reproduction trunk pan. NOTE* If you buy both sides left and right we can leave them as one continuous panel at no extra charge just for the asking, please leave a note on your online order in the comments section. ...

Trunk patch panel cut in house from a complete transition panel. This is a patch for the area forward of the fuel tank just before the transition hump. 

Steel fitting for 390-4V / 427-4V and 428CJ engines with the PCV transfer tube.Replaces C7AZ-9A474-A. Painted Ford Corporate Blue from the factory.

NOS air cleaner breather element filter assembly for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, "AUTOLITE" marked also FA-79.  Casting number D0OF-9D696-A. Ford part number D0OZ-9D695-A.

Front steel vacuum fitting for 390, 427, 428CJ engines.Replaces Ford part number C7AZ-9A474-A.

Used brass intake manifold fitting that screws into the rear of the 390GT and 428 CJ intake manifold on all 1967-68 cars so equipped. Similar to the 1969 version, but this one does not have the additional smaller nipple.Replaces Ford part number C8OZ-9A474-A.

Used brass intake manifold fitting that screws into the rear of the 428 CJ intake manifold on all 1969 428 Cobra Jet engines. Similar to the 1967-68 version, but this one has an additional smaller nipple coming out of it.  Ford part number C8OZ-9A474-A.

NOS valve cover grommet for PCV valve on 1970 Mercury Cougar and Ford Mustang with steel valve covers.  For "D" shaped hole, steel valve covers. Ford part number D0OE-6A892-A.

NOS New Old Stock PCV valve grommet for 1970 Mercury Cougar and Ford Mustang. Round style with notches for twist locking into the stock valve covers. Ford part number D0AZ-6A892-A.

This fitting screws into intake manifold, has 1/2" nipple for PCV hose, 3/16" vacuum port nipple and threaded hole for smaller accessory fitting. 5/8 by 20 thread pitch

This fitting screws into intake manifold, has 1/2" nipple for PCV hose, 3/16" vacuum port nipple and threaded hole for smaller accessory fitting. Painted Ford Corporate blue from the factory.

PCV TUBE, fits stock GT cast iron manifolds, replaces Ford part number C6AZ-6758-A. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 390 tube has a little less pronounced angle. Fits all 1967-68 S code 390-4V Ford engines. You will need the related fittings for installation.

100% Concours Correct PCV Tube for the 1968 Mercury Cougar 427 GT-E, Ford Mustang, Fairlane, or Torino with the 428 Police Interceptor, fits either # C6AE or # C7AE Aluminum PI intake manifold. Replaces Ford Part #: C6AZ-6758-B.

PCV tube for the Mercury Cougar, Ford Mustang GT500KR and Torino with the 428 CobraJet and Super CobraJet for 1968-69 and C8OZ-9424-C factory iron intake manifold. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 428 tube has a less pronounced angle, this is due to the taller 428CJ intake manifold. A less pronounced angle fits more closely to the passenger side valve cover. Replaces Ford Part #: C8OZ-6758-B.

PCV TUBE, fits stock GT cast iron manifolds, replaces Ford part number C6AZ-6758-A. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 390 tube has a little less pronounced angle. Fits all 1967-68 S code 390-4V Ford engines. You will need the related fittings for installation. Our used 390 transfer tubes will often times have a dent or ding in the metal tube. The repro is a very top quality alternative, they would be concours correct in appearance.  ...

Reproduction positive crankcase ventilation valve or PCV valve for 1968 Mercury Cougar, Cyclone, Ford Mustang and Torino all with 390GT or S code 390-4V engines. Additionally this fits all 428 Cobra Jet and Super Cobra Jet engines 1968-1/2-1970. This valve has a stamped casting number of C8OE-6A666-B, comes with a white plastic ring as shown. Ford engineering number C8OZ-6A666-B. Also used on 1967 Shelby Mustang GT500, Ford 428PI, and Mercury Cougar GT-E 427-4V engines. *Note - Must be used...

This adapter is threaded on bottom for Boss 302 / 390-4V / 428CJ PCV valve and 6 degree nipple on side. Gold Cadmium plated, not painted originally. This only works with the OEM or reproduction threaded PCV valves.Replaces Ford Part Number C7OZ-6A706-A.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Reproduction pigtail for repairing the ignition switch on the 67 Cougar or Mustang. 

NOS wiring pigtail without the resistor wire for repairing ignition switches on 1968-69 Cougars, Mustang, and other Fords.Ford part number C9AB-14313-A.

Reproduction wiring pigtail without the resistor wire for repairing ignition switches on 68-69 Cougars and Mustang. NOTE - We've found that the clips on this plug don't lock into the ignition switch and will need to be modified to make fit.

Reproduction pillar post mouldings that feature and vinyl overlay for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Used pin for the cable that goes to the vacuum motor used in actuating the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Used only in the first part of 1968, later in the year this was upgraded to a clevis. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Locking pawl catch pin for your 67-69 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Pliable, soft used trim with no burns or nicks. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake drum from it for a few days. Do know that all interior trim parts we sell will be discolored and will need to be repainted, sun fade will be...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Hardened from heat, grade B will crack if folded in half on a cold day. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake drum from it for a few days. Do know that all interior trim parts we sell will be discolored and will need to be...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Pliable, soft used trim with no burns or nicks. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake drum from it for a few days. Do know that all interior trim parts we sell will be discolored and will need to be repainted, sun fade will be...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Hardened from heat, grade B will crack if folded in half on a cold day. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake drum from it for a few days. Do know that all interior trim parts we sell will be discolored and will need to be...

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to these parts can avoid several hundred dollars in damage. These...