All Products

This rechromed lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several...

This was the inner air cleaner lid used on the Mercury Cougars equipped with a 428 Ram Air Cleaner or 429 Cobra Jet Ram Air Cleaner assembly. Although you will often find chrome under the blue engine paint on these lids they are in fact supposed to be painted from the factory. This lid is 14-1/8 inches in diameter. The reason you will often see chrome underneath the paint is that this is the same lid used on the 1967 427 GTE, 289 HiPo equipped early Mustangs and 390 GT / GTA Fairlanes and...

This Grade A quality ashtray lid was located at the rear of the console and was used on all 1967 - 1968 Mercury Cougars except the 1967 standard model and the 1968 XR7G. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish and a slightly taller lower section. The removable ash receptacle is sold separately.Ford part # C7AZ-6330714-A.

This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. A bit of investigation shows us that an inline fuse was used on the single wire and it has an amp rating of 7.5 amps.Replaces part # C9WY-15702-A

Good used light bar for the convenience control indicator lights on the 1967 Cougar dash face pad. Indicators lights are for belts, door, fuel and park.

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out this video

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Manual control shift linkage assembly for a floor shift FMX transmission in any 1969 Mercury Cougar or Ford Mustang. Comes as shown.  1969 linkage is different than 1970, 1970 included a provision for the steering column lock out rod. Check out this video

Manual control shift linkage assembly for a floor shift FMX transmission in any 1971-73 Mercury Cougar or Ford Mustang. Comes as shown. *Note - this will not work with a C6 transmission.

A perfectly working, matched set of trunk and glove box locks with key is getting rather hard to come by these days. These two matching locks are guaranteed to work perfectly. Includes 1968 style glove box lock, 1967-68 Cougar trunk lock cylinder with one "Ford" cut key to the coded to the number imprinted on the glove box lock. This is a matching set with new key. 1967 glove box locks has square edges on the front of the lock. Starting in 1968 the lock had a rounded edge on the front. We also...

Used locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth. These units will be mint with no broken or chipped teeth....

This is a rebuild service in which we will replace the locking pawl and cable. We provide this service for Cougars, Mustangs and T Birds.Ford part number C9ZZ-3E520-A THIS SERVICE REQUIRES THAT YOU SEND IN YOUR CABLE IN ADVANCE.

Locking pawl cable assembly for 67 - 69 TILT column T-Birds.

Rod used for locking the C-6 transmission in "Park". Connects to the lower tab of the steering column and the C-6 transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a red paint mark or daub. Casting number stamped on the rod - D1ZA-7E330-BA. The C-6, automatic transmission, could be ordered with any engine from 1971 - 1973. Transmission code "U" on your door data tag.

Finally a quality reproduction lower control arm for the one year only 1967 lower control arm! Deigned to work with your existing articulated strut rod arms found only on the 1967 Mercury Cougar. *NOTE – Can only be used with 1967 Cougar lower control arms C7WY-3468-C (ITEM # 15393). Replaces Ford Part # C7WY-3078-A Check out this video

Used chrome moulding that attaches horizontally to the bottom of the headlight bucket. Driver side for any 1971-73 Mercury Cougar. 1973 used a different casting number but the parts are exactly the same. A grade will have nice chrome, and maybe one minor blemish. We consider these 'show quality' rather than 'driver quality'. We do offer a B Grade version of this part, and always have them in stock.Replaces Ford part number D1WB-13B167-AB and D3WB-13B167-AA.

Restored driver (left hand) side lower headlight housing moulding for any 1971-1973 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Mercury casting # D1WB-13B167-AB or D3WB-13B167-AA.

Used chrome moulding that attaches horizontally to the bottom of the headlight bucket. Passenger side for any 1971-73 Mercury Cougar. 1973 used a different casting number but the parts are exactly the same. A grade will have nice chrome, and maybe one minor blemish. We consider these 'show quality' rather than 'driver quality'. We do offer a B Grade version of this part, and always have them in stock.Replaces Ford part number D1WB-13B166-AB and D3WB-13B166-AA.

Restored passenger (right hand) side lower headlight housing moulding for any 1971-1973 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Mercury casting # D1WB-13B166-AB or D3WB-13B166-AA.

Used grade A lower center console pad for the 1967 Standard Automatic Transmission. We rarely have these in stock so the chances of getting the color you desire is slim. We have several Grade B's with cigarette burns, cracks and the like for substantially less money.

Used grade B lower center console pad for the 1967 Standard Automatic Transmission. We rarely have these in stock so the chances of getting the color you desire is slim. 

Used only in 1968 on non xr7 models and Mustang. Very hard to come by with no splits, burns or cracks. We often can supply the color you desire, please let us know your desired color and we will try. Grade B will need to be repainted and will not be as soft and straight as grade A. The simulated stitching embossed in the vinyl may show areas of slight separation.

This pad is in poor condition. You can actually modify a automatic pad to work with your manual transmission chrome bezel. *NOTE* If you have a clean example of this pad for sale we would like to hear from you!

Good lower pad with no cracks or burns. We have several of these in stock but cannot guarantee we can give you the color you select. Mention in the notes of your order what color you would like and plan on repainting this item even if we can provide your color as there is always some discoloration from age and use.

Good lower Grade B pad with no cracks or burns. We have several of these in stock but cannot guarantee we can give you the color you select. Plan on repainting this item even if we can provide your color as there is always some discoloration from age and use. Grade B will be pulling away from the base and will need glued.

Reproduction CHARCOAL lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

This version with a cast head was only found in the earliest 1967 Mercury Cougars. 13/16 inch socket. Much better quality than the later stamped steel version.

Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.  These are best suited for 1971-73 Cougars. To run a tire larger than a 225/60/15 you may have to modify your fenders and quarters.  NOTE! These wheels are intended to be...

New aluminum 15x8" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it!  This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center.  We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

RAT-BZ1 Original equipment 3 speed top loader 3.03 transmission from a 1972 Mercury Cougar with engine code H - 351-2V only. This transmission was used after 12-1-1971 through the end of the 1972 model year. Ford master part number D2ZZ-7003-G.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each...

RAT-BZ Original equipment 3 speed top loader 3.03 transmission from a 1972 Mercury Cougar with engine code H - 351-2V only. This transmission was used from the beginning of the model year through 12-1-1971. Ford master part number D2ZZ-7003-C.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X...

RAT-BB1 or RAT-BB2 Original equipment 3 speed top loader 3.03 transmission from a 1971 Mercury Cougar with engine code H - 351-2V only. Transmission with casting number RAT-BB2 also used during this model year. Ford master part number D0ZZ-7003-C.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each...

This is for your three or four speed manual transmission 1970 Cougar. The 70 is unique over the 69 in that it does not have a provision for your seat belt buckles. Absolute perfection in every detail, if all reproductions were this nice there would be no market for used parts. This unit has no alignment holes for the woodgrain bezel for those that prefer the cleaner look.

This is for your three or four speed manual transmission 1970 Cougar. The 70 is unique over the 69 in that it does not have a provision for your seat belt buckles. This part requires an additional woodgrain bezel that affixes to the top, we also have one listed that does not require the additional bezel. Absolute perfection in every detail, if all reproductions were this nice there would be no market for used parts. *Note - This console part does have pre-drilled holes for installing the...

Used map light assembly for the Mercury Cougar standard or Eliminator. This unit has the switch installed on the housing and mounts under the dash pad on the passenger side (right hand). Assembly comes with housing, lens and wiring harness. After January 1970, Mercury changed the housing to plastic. We occasionally have those versions, please ask. This unit measures about 6-1/8" long, 1-11/16" wide and about 1-5/16" deep. *NOTE* Because this unit has the switch mounted in the housing, it...

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In In 1968 they were embossed with the iconic walking cat design. In 1967 they used a floral design which was the same left or right. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In In 1968 they were embossed with the iconic walking cat design. In 1967 they used a floral design which was the same left or right. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In In 1968 they were embossed with the iconic walking cat design. In 1967 they used a floral design which was the same left or right. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In In 1968 they were embossed with the iconic walking cat design. In 1967 they used a floral design which was the same left or right. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In In 1968 they were embossed with the iconic walking cat design. In 1967 they used a floral design which was the same left or right. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In In 1968 they were embossed with the iconic walking cat design. In 1967 they used a floral design which was the same left or right. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In In 1968 they were embossed with the iconic walking cat design. In 1967 they used a floral design which was the same left or right. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In 1967 they used a floral design which was the same left or right. In 1968 they were embossed with the iconic walking cat design. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.