All Products

1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.

The 1967 Cougar was Mercury's attempt to enter the Pony Car market segment popularized by the April 1964 introduction of Ford's Mustang. Introduced in the fall of 1966 for the 1967 model year, the first-year 1967 Cougar exceeded all sales expectations with 150,893 units sold. It was selected as Motor Trend's 1967 Car of the Year. Legendary Cougar Magazine is dedicated to the first three generations of Mercury's luxury Pony Car. Each bi-monthly issue includes features on the first-generation...

Used " Red " high beam indicator lens for the Mercury Cougar. This is for late 1968 which uses the small housing. The 1967 lens was blue in color. The lens may have a slight arc to it due to the heat from the bulb over time.

Used high beam indicator lens for the 68 XR7 Cougar.

C4AZ-13564-A

Part of Ford part #C9AZ-15A201-C assembly. My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertable, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you couldn't deal with two better examples of what our hobby is really all about, making friends. Mark (mercurycougar.net)...

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

Used tumbler linkage arm that connects to the to ignition switch on your 1970 Cougar or Mustang equipped with a tilt column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Rare find, must have for your Concours Cougar. Sold individually.Ford part number C5ZZ-1012-BFits the following models with Styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang

Used middle console support bracket. Held in place by 2 rivets midway under the console.

Special cast-metal bracket glues to windshield. Fits the original and most reproduction mirror ball arms. This version is shiny chrome instead of satin silver like the originals. The screws are also incorrect. Otherwise nice quality.

Original used hard plastic sport mirror pad / gasket. Correct for driver side sport mirrors for the 1971-73 Cougar and passenger side sport mirrors 1970-73. Ford engineering # C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

This used driver side (left hand) mirror pad / gasket for use with a standard manual adjust chrome mirror. This unit will not work with a painted sport mirror or any remote mirror. Ford Engineering # imprinted on pad is C7OB-17C701-AA or C8OB-17C701-A. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a...

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit. Original Mercury part number is C7WY-6529034-A with a casting number of C7WB-6529034-D

Core driver side (left hand) lower rear window moulding / trim for the Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42405-A.

Core passenger side (right hand) lower rear window moulding / trim for your Mercury Cougar suitable for restoration or could be used on a lower quality driver. Ford part # C7WY-42404-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Stainless steel throttle pedal surround trim. Self attaching to part number D1ZZ-9735-B. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. It appears that this trim may not have been used all the way through 1973. Ford probably eliminated it as a cost saving measure.

Driver side upper windshield mouldinig. Suitable for restoration or could fit right in on or your lower quality daily driver. Ford part number C5ZZ-6503145-B.

Driver side vertical windshield moulding. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part number C5ZZ-6503137-B.

Core passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503144-B.

Core passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503136-B.

Bolt that goes through the air pump mounting bracket. Pump rotates on this bolt. Bolt size 3/8"-16 x 4.25" long.

1971 - 1973 Convertible spare tire mounting, J bolt. MPC lists the total length as 9-1/2 inches long, and 5 inches threaded. Application is for hubcap type wheels only, those of you fortunate to have the style steel wheels need C8OZ-1448-A above.

Good reproduction but our used unit is a better value and will clean up just as nice.

Reproduction mounting bracket. This is the mounting plate for the end links on the factory rear sway. Mercury Cougar 1970-73 only, this is not a Mustang part. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very...

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Nicely chromed dipstick tube and dipstick for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor. Replaces Ford part # C9OZ-6750-A or D0AZ-6750-C.

Reproduction blue dipstick tube for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor.

The oil filter made by the original Ford supplier.

This is the second printing so it does include the xr7 package.

Reproduction Owners Manual for the 1968 Mercury Cougar

Has correct textured cover. Quality reproduction.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used door hinge anchor plate for attaching the door hinge to the body pillar. All positions are the same, upper, lower, driver and passenger sides. Fits all 1969-70 Mercury Cougar and Ford Mustang.Ford part number C9ZZ-6502666-A.

One required per car, mates to female version attached to the under dash loom. Same plug for tilt and non tilting columns.

This rubber plug is found on the bottom side of 68 and 69 Cougars without tilt column. It covers the access hole for the bolt that removes the column head / collar. We notice that most cars do not have them in place. This could be due to over site at the factory or them being lost over the years as the car has been serviced. We have also noted that Dearborn cars rarely if ever have them present and San Jose built cars often have them in place. If you have a Dearborn built car and have this...

Used taillight wiring harness repair plug and pigtail to the passenger side (right hand) center taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

This poster is a meticulous recreation of the 1968 original that Lincoln-Mercury dealerships had on display in their showrooms to advertise the Cougar XR7-G. We were able to have an original poster professionally scanned, the images were restored, and the text carefully recreated to match the original. The result is a fresh new version of a rare, iconic display piece.This 24" x 36" poster is smaller than the original, which was a massive 36" x 48". This makes it easier to display, and easier...

D1ZZ-6523313-A Bracket that attaches the end of the power window motor to the door on the driver side of 1971-73 Cougar and Mustangs with power windows.

D1ZZ-6523312-A Bracket that attaches the end of the power window motor to the door on the passenger side of 1971-73 Cougar and Mustangs with power windows.