General (Old Category Structure)

Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.

Crankshaft oil slinger for all 351C or Cleveland engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number D0AZ-6310-A.

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

For all 1969 and 1970 Cougars with H code 351-2V and M code 351-4V engines and FMX automatic transmissions. This part weighs 2.66 pounds and when set on a level surface the height of the mounting hole on the driver side measures 3" on center and the passenger side 3 1/8" on center. Ford part number C9ZZ-6A023-A. *NOTE* The picture with all four crossmembers in a line shows the three versions of the small block C-6 and FMX units in the foreground and the last is the big block C-6 unit. Notice...

For all 1971 to 1973 Cougars and Mustangs with H code 351-2V and FMX automatic transmissions.  Ford part number D1ZZ-6A023-B.*NOTE* Two notes - There is a difference between 1969-70 and 1971-73 FMX cross members. Additionally, Ford did produce H code 351-2V engines with C-6 transmissions. Triple check.

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. This is the reproduction cross member offered by most of the Mustang...

Good quality reproduction front cross member for your 71 - 73 Cougar or Mustang. This is the frame / body piece that goes underneath your core support and receives the front ends of the strut rods. Sold as a stand alone part and does not come with strut rods or any strut rod hardware.Width: 34.75"Diagonal from outer bottom corner to outer top edge: 5"

Good original part that has not been noticeably twisted, bumped, bent, or heavily rusted. Notice the factory indentations that are a result of the manufacturing process (dent from jig). Also know that there is always at least a couple minor dings or scrapes from decades of being the lowest point of the car. Much better fit than repro and note the repro is made from thinner gauge steel. Also know that we generally do not bead blast our used parts before sending them but often we show them on...

This reproduction radiator support crossmember is correct for the 1967-68 Mercury Cougar and Ford Mustang, but will work on any 1967-70 Cat or Pony.Replaces Ford # C7ZZ-6510852-B or C9ZZ-6510852.

New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD. 

Reproduction Crossmember / Under Engine for the 1971 - 1973 Mercury Cougar / 1971 - 1973 Ford Mustang 

Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom made Walking Cat belt buckle for the Cougar die hard. This would make a great gift for anyone who lives and breathes everything Cougar. The buckle is bare, unpainted and ready for you to customize how you see fit. We're not sure how we ended up with this awesome collectable, but it's definitely one of a kind and the only one we know of, so when it's gone it's gone!  Measures 3 3/8" x 2 1/4"

1967 Front unibody cut, this one has only one torque box which is located on the driver side of the car. If originality isn't an issue we recommend 1968 versions that have both torque boxes, which adds strength. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual...

1967 Front unibody cut, this one has only one torque box which is located on the driver side of the car. If originality isn't an issue we recommend 1968 versions that have both torque boxes, which adds strength. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual...

1968 Front unibody cut, these 1968 front structures have two torque boxes, unlike the 1967 with only one. This item has the cowl cutouts for factory air conditioning. No shock tower reinforcing, consider 1969 front cuts if you desire the bracing. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of...

1969 Front unibody cut, these 1969 Mercury Cougar front structures all have reinforced shock tower braces like the 390 and 428 Cobra Jet Mustangs. Mustang guys, please note, we do not have them without these braces. This cowl only ships with the holes for the factory air conditioning. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford...

1970 Front unibody cut, these 1970 Mercury Cougar front structures all have reinforced shock tower braces like the 428 Cobra Jet Mustangs. Additionally these have the cutouts on top of the radiator core support for the Mustang twist locks. Mustang guys, please note, we do not have them without these braces. This cowl has the holes for the factory air conditioning. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No...

1971-72 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1973 frame rails are constructed differently for the energy absorbing front bumpers. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

1973 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1971-72 frame rails are constructed differently for the non-energy absorbing front bumpers. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

1968 Front unibody cut, these 1968 front structures have two torque boxes, unlike the 1967 with only one. This item does not have cowl cutouts for factory air conditioning. No shock tower reinforcing, consider 1969 front cuts if you desire the bracing. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours...

1969 Front unibody cut, these 1969 Mercury Cougar front structures all have reinforced shock tower braces like the 390 and 428 Cobra Jet Mustangs. Mustang guys, please note, we do not have them without these braces. This cowl only has the holes for the heater hoses only, not cut for factory air conditioning. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a...

1970 Front unibody cut, these 1970 Mercury Cougar front structures all have reinforced shock tower braces like the 428 Cobra Jet Mustangs. Additionally these have the cutouts on top of the radiator core support for the Mustang twist locks. Mustang guys, please note, we do not have them without these braces. This cowl only has the holes for the heater hoses only, not cut for factory air conditioning. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or...

1971-72 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1973 frame rails are constructed differently for the energy absorbing front bumpers. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

1973 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1971-72 frame rails are constructed differently for the non-energy absorbing front bumpers. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

Comes with good shock towers, front aprons, and core support. This is a great value for those that need to replace multiple parts upfront as you will not only get factory joined parts that will save you money and time, but it will also  preserve the value of your car. With a clean Western cut like this, one should be able to install it so that nobody would ever know your car has had anything replaced. You will have to call to order this one. Expect to pay about $300 for crating and...

Single cylinder head from 1967 Mercury Cougar with non smog 289 engines, 289-2V and 289-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 54-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.3:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C6OE-M or C6OE-6090-M.These weigh...

Single cylinder head from 1968 Mercury Cougar 289 engines without smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 61.7-64.7 cc's. With stock pistons, these heads will net an approximate compression ration of 8.7:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C8OE and "289".*Note - These low compression heads are not...

Single cylinder head from 1968 Mercury Cougar 302-2V engines without smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 61.7-64.7 cc's. With stock pistons, these heads will net an approximate compression ration of 8.7:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C8OE-J and "302" and "2-V".*Note - These low compression heads...

Single cylinder head from 1968 Mercury Cougar 302-4V engines without smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 52-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C8OE-D and "302" and "4-V".Current casting dates include: 7G25,...

Single cylinder head from 1970-73 Mercury Cougar with H code 351C-2V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.65 inch valves, and the chambers measure out at 78.2 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-J. 2V in the...

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...

Single cylinder head from 1970 Mercury Cougar H code 351W engines, 351-2V. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0OE-6090-C. 1970 351 Windsor engine, not to be confused with the 351 Cleveland engine from the same year.These weigh 53 lbs. each, and cannot be...

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped holes for exhaust manifolds. These weigh 48 lbs. each, and cannot be combined with other items...

Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. These cylinder heads are factory drilled and tapped for thermactos smog tubes. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust...

Single cylinder head from 1967 Mercury Cougar with 390-4V engine with California thermactor smog ports. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes. Current...

The W code Cougar 427 GTE used these heads on a side oiler rotating assembly with a hydraulic cam and Medium Riser aluminum intake - the so called "PI" C7AE version. 427 cylinder heads that have the J's have provision for 14 bolt exhaust manifolds. Low Riser 427 heads use 2.09" / 1.66" valves. Included is a set of machined used valves (16 total)  The C8AE-6090-J heads were also used on the prototype 50 Mustang fastbacks used at the 1968 Winter Nationals - the so - called "135 series"...

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.