General (Old Category Structure)

Standard size front sway bar bushings were 3/4 inch from 1967 - 1970. Rubber construction, sold in pairs only. Replaces Ford Part #: C7OZ-5493-C or C6OZ-5493-B.

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-E

It took a long time but our supplier finally got this bushing right. They ended up copying a never installed production original bushing Ed Meyer acquired from the Kar Kraft factory back in the day. All details have been copied including the two small ribbed lines located on one side. NOS Bushing notes: If you have NOS C9ZZ-5493-A front sway bar bushings in a Ford bag good luck making them fit. Yes, its a documented fact that almost all NOS 15/16" sway bar bushing Ford sold in a bag are too...

This is the longer of the two versions found on the 1967 XR7 and also found on the Shelby and Mustang. The lens used with this reset button has a smaller hole than the 1968 version.

There were two versions of this button and this is the shorter of the two found on the 1968 XR7. Has good internal spring and pit free knob. Used in conjunction with the 1968 lens with a larger pass through hole.

Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate.

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate.

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Internal tail shaft assembly from a C4 transmission. We only disassemble up to what you see in the picture.  *Excludes later versions of C4 transmission that have thicker output shafts.

NOS C6 Automatic Transmission training handbook from the Ford Marketing Corporation. Course 7521, Vol. 71 S4-L2. Everything from the torque converter, to the planetary gear and hydraulic systems to diagnosis and adjustments are detailed in this manual. Everything about descriptions, testing procedures and specifications were approved by Ford. Filled with color photos and diagrams. There is an unknown name written on the inside of the cover, however all pages are intact and in perfect...

Internal tail shaft assembly from a C-6 transmission. We only disassemble up to what you see in the picture. 

This reproduction economy front emergency / parking brake for the Mercury Cougar or Ford Mustang fits from the handle to the equalizer. 1 required per car. Replaces Ford part # C9ZZ-2853-A.

Premium reproduction, near concours correct front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. This cable hooks onto your inside foot activated brake assembly inside the car, through the floor board, and hooks to the brake equalizer cable under the car. This unit is very close to an OEM replacement, much better than our economy cable.  ...

Premium, reproduction, and near concours correct front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. This cable hooks onto your inside foot activated brake assembly inside the car, through the floor board, and hooks to the brake equalizer cable under the car. This unit is very close to an OEM replacement, much better than our economy cable. ...

This used emergency / parking cable anchor bracket is spot welded to your passenger side (right hand) front floor pan and anchors the cable. Comes "as taken from parts car". *Customer Feedback* from mercurycougar.net: "Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting...

Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.

Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-3/4 inches long. Replaces Ford part # C9ZZ-2A635-D.

Reproduction emergency / parking brake cable for the Mercury Cougar or Ford Mustang with V-8 engines, that is approximately 133 1/8" long. This unit fits from equalizer to rear brakes and one is required per vehicle.Replaces Ford part # D0ZZ-2A635-A.

Reproduction passenger side (right hand) rear emergency / parking brake cable that fits from the equalizer to rear brakes. 1 required per vehicle. Cable length is approximately 136 5/8". Correct for 1968 Mercury Cougar and Ford Mustang, but fits 1967 Mercury Cougar and Ford Mustang with the companion left side cable. Replaces Ford part # C8ZZ-2A635-A.

Reproduction economy quality emergency parking brake cable that runs down the passenger side (right hand) of the car. This unit fits from equalizer to rear brakes and one is required per vehicle. Cable length is approximately 133 3/4". NOTE: Please reference the photo above for installation details. The toothed clip needs to be set in place properly or it simply will not fit. You may need to use pliers to pull from the inside of the backing plate. Replaces Ford part # C9ZZ-2A635-D. ...

Concours correct premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one located on the driver side and is an exact fit for 1968 and 1969 Mercury Cougar and Ford Mustangs.

Premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one, 31 inches, located on the driver side and is an exact fit for 1970 - 1973 Mercury Cougar and Ford Mustangs. Ford Part # D0ZZ-2A635-B

This reproduction rear emergency / parking brake cable kit fits from equalizer to rear brakes. 2 required per vehicle. Equal length emergency brake cables for 1967 on both the Mercury Cougar and Ford Mustangs. Upgrading to the 1968 unequal length cables can easily be done. Equal length cables is correct for 1967 Mercury Cougar and Ford Mustangs. Fits L.H. or R.H., the Cougar uses a longer keeper than the Mustang to compensate for the added wheel base length. Replaces Ford part # C7ZZ-2A635-A,...

This reproduction rear emergency / parking brake cable kit fits from equalizer to rear brakes. 2 required per vehicle. Equal length emergency brake cables for 1967 on both the Mercury Cougar and Ford Mustangs. Upgrading to the 1968 unequal length cables can easily be done. Equal length cables is correct for 1967 Mercury Cougar and Ford Mustangs. Fits L.H. or R.H., the Cougar uses a longer keeper than the Mustang to compensate for the added wheel base length. Replaces Ford part # C7ZZ-2A635-A,...

This attaches to the end of the cable that attaches to the hand ratchet e-brake. It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted.

Front emergency brake cable bracket that welds to the floor under the drivers side floor board.  It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1969-70 Mercury Cougar and Ford Mustang.

Front emergency brake cable bracket that welds to the floor under the drivers side floor board.  It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1971-73 Mercury Cougar and Ford Mustang.

Nice reproduction fresh air vent cable pull assembly. Comes with dash mounted bracket as shown. Much stronger construction than the originals, which were made with a plastic sleeve instead of metal.Replaces Ford part number C7ZZ-6501891-A and C7ZZ-6501891-C.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing.Ford part # C7ZZ-6501891.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing, very tough part for us to keep in stock. The metal version is a better part and you can get our metal reproduction unit right here!Ford part # C7ZZ-6501891. ...

Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A

Under dash bracket used to mount the pull cable for the fresh air vent on the driver side of your Mercury Cougar or Ford Mustang.

Used mounting and indexing bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket goes behind the dash panel and keeps the vent cable attached and indexed correctly. A 7/16-14  hex nut is also needed for mounting the cable. (Sold separately)Replaces Ford part number D1WY-6501822-A.

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

Aluminum housing for the sunroof cable drive, connects to the motor on any 1967-73 Mercury Cougar and many other vehicles that used the Golde sun roofs. Golde was a company from West Germany and also supplied parts to many other auto manufacturers such as Mercedes-Benz, Porsche, VW, BMW, Mopar, and Ford. ASC was the company that installed sun roofs for Ford US, and they used Golde components. Casting number Golde 100 413 600 / Golde 100-413-600 / Golde 100413600. ...

Aluminum cover for the sunroof cable housing on any 1967-73 Mercury Cougar and many other vehicles that used the Golde sun roofs. Golde was a company from West Germany and also supplied parts to many other auto manufacturers such as Mercedes-Benz, Porsche, VW, BMW, Mopar, and Ford. ASC was the company that installed sun roofs for Ford US, and they used Golde components. Casting number Golde 100 413 605.

This used emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. Replaces Ford part # C6OZ-2A602-A.

Reproduction cable guide for the 67 - 73 Cougar or Mustang equipped with a sunroof. These are the guides that hold the cables, and slide back forth on the sliding roof panel assembly as seen on page 14 of the sunroof manual. Sold individually.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford Part # C7ZZ-2A808-A.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford part # C7ZZ-2A808-A.

Used mounting bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket mounts to a tab on the fresh air vent, and keeps the cable stationary.  Replaces Ford part # D1WY-18C587-A.

Used steel bracket for mounting the passenger side fresh air vent cable to the bottom of the dash below the glove box. 1971-73 Mercury Cougar only.Replaces Ford part # D1WA-6501861-AC.*NOTE* Does not fit Ford Mustang.

Reproduction heater cable set for your beloved Cat or Pony. This set is an exact fit! Replaces Ford part # C7ZZ-18518-A. *Customer Feedback*     "My first deal with Don was clear back in the 1980's and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you...

Sold as a pair. These often become dislodged due to the force required to be applied after they have rusted in place for decades. Located at the bottoms of the fenders.Ford part number 359613-S2.

Sold as a pair. These often become dislodged due to the force required to be applied after they have rusted in place for decades. Located at the bottoms of the fenders.

California emission control "Caution" decal for the 1970 Mercury Cougar and Ford Mustang.

Reproduction California Emission Control Caution Decal for the 1970 Mercury Cougar / Ford Mustang