Clearance / Overstock

These are also a good replacement bulb for the 67-68 under-dash courtesy lights as they are easier to grip than the 631 bulb.

Reproduction 1893 Interior Radio Light Bulb for the 1967 - 1973 Mercury Cougar

Replacement bulb for the door ajar warning light panel. This replacement bulb does not have the flashing feature like the OEM GE 256 installed bulbs. The original bulbs have a heat tab that flashes the bulb after a couple of seconds.

Small block dipstick tube for the 1968 Cougar and Mustang. Nice chrome finish to catch the eye. Will also fit on 1969 Mustangs with a 302 engine.

Reproduction intake manifold nut for the 289 or 302 on the 1968 Mercury Cougar and Ford Mustang (and possibly other Ford / Mercury cars). 5/16-18 X .72 X .33 zinc free-spin flanged nut. Sold individually. Replaces Ford part #: 374031-S

Reproduction interior turn signal indicator 53x light bulb for the Mercury Cougar. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Dome light bulb for the standard (non-XR7) 1791, 1972, or 1973 Mercury Cougar.

Reproduction 97 License Plate Light Bulb for the 1967 - 1973 Mercury Cougar

New reproduction A/C control knobs for your Mercury Cougar or Ford Mustang / Shelby.

These selector buttons are top quality reproductions with a lot of attention given to the details to make these little units look factory fresh and correct.

Reproduction Air Conditioning Vent Air Door Axle for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Reproduction Air Conditioning Vent Air Door for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Round air conditioning vent registers for all 1967-68 Mercury Cougar and Ford Mustang with factory A/C.

Reproduction factory air conditioning vent register knob. This knob controls the black vent door or valve inside the round registers. These will fit the original axle shafts, but will need to be attached with some super glue or other adhesive. These new knobs fit our reproduction axle shafts that have new splines on them perfectly. Please note the position or orientation of the knob in relation to the position of the internal black plastic butterfly.

Stainless insert that fits in holes around wheel.Fits the following models with styled steel wheels:1969 Mercury Cougar1970 Mercury CougarThese inserts fit or both the 1969-70 OEM Cougar styled steel wheels and the reproduction 1969-70 styled steel wheels. These are the most up to date version of these bezels. The originals tend to have a more mirrored finish like the stainless steel window trim, these reproductions tend to have a brushed nickel look to them.Sorry, these do not come with...

Set of 20 stainless inserts that fit in holes around wheel.Fits the following models with styled steel wheels: 1969 Mercury Cougar1970 Mercury Cougar These inserts fit or both the 1969-70 OEM Cougar styled steel wheels and the reproduction 1969-70 styled steel wheels. These are the most up to date version of these bezels. The originals tend to have a more mirrored finish like the stainless steel window trim, these reproductions tend to have a brushed nickel look to them.Sorry, these do not...

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

This is a reproduction of the original engine displacement decal. Black on chrome background followed by black background with chrome head and lettering 390-2V located on the top of the air cleaner.*CUSTOMER REVIEW* Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell...

This is a reproduction of the original orange engine displacement decal with black lettering and black and white checkerboard on each end that was located on the top of the air cleaner. This decal is for models without the GT package.Fits the following models with 390 4 BBL engines:67 Mercury Cougar1967 Ford Mustang Replaces Part #: C5AF-9638-D ...

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Reproduction Alternator Connection Nut for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold insividually 

Reproduction Alternator Connection Nut for the 1970 Mercury Cougar or Ford MustangSold individually

Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang

Replaces Ford Part # C8AZ-2B164-A Sold individually

Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being blunt about the quality on some of these items, but after using these...

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # C8ZZ-6524100-BK.

Sold individually # 374212-S

Captured washer, or spinning washer nut for attaching the headlamp motors or vacuum actuators on the 1969-70 Mercury Cougar. All models, Standard Hard Top, XR7, and Eliminator. Two needed per car, sold individually.

Replaces Ford Part # 50828-S Sold individually. Zinc Dichromate (yellow-rainbow)

This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.

Replaces Ford Part #: D3AE-9C485-AFA

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

Barrel nut for the 3/16" stud found on the 6.5 Liter badge and the GT badges that mount on the fender of 1967 Mercury Cougar and Mercury Cyclone GT with the S code 390 engine. Same GT badge on the 1968 Mustang GT models. Item sold individually. The install is basically the same as shown here: https://youtu.be/mcd788WUNns

These barrel nuts or clips are exactly like the original ones inserted into the trunk for attaching 1967-68 "Mercury" script, and 1971-72 Mercury Cougar "Mercury" Hood scripts. The manufacturer indicates that these tubular nuts fit 1/8" holes. Pin size on those emblems are 3/32". These clips are also used to attach the 1967 quarter panel emblems. The install is basically the same as shown here: https://youtu.be/mcd788WUNns ...

Not the correct wood grain for a Cougar.... Here is a piece that will allow to install a modern DIN radio / CD player into your Mercury Cougar or Ford Mustang. No hacking or cutting required! *TRIVIA* Here's some alphabet soup for you. DIN stands for Duetch Industri Normen. An abbreviation for a standard in-dash radio measurement which is approximately 2 inches by 7 inches. The Germans starting using it to standardize the radio's in Audi's, BMW's, Mercedes, and VW's way back in the mid 80's....

New rubber body plug, fits 9/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles, typically they are for: front fender aprons, transmission cross member, and radiator support. Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 376966.

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-3/8" oval holes. Sold individually, Usually 1 per car. Fits 1971-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 384440.

Reproduction rubber body plug for the Mercury Cougar and Ford Mustang. This 11/16" x 15/16" oval unit fits to the top of the cowl underneath the front fenders. These little units are sold individually, and their are usually two required per car. Replaces Ford plug marked 383181-S.

New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan, side of cowl at door, and LH apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377949.

New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S.

 Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!

Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!

Replaces Ford Part # C9OZ-6065-B

Replaces Ford Part # 43260-S Sold individually

Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.

Front U clamp sway bar bracket bolt, for any 1967-68 Mercury Cougar or Ford Mustang. 3/8-16 x 1.0 Grade 5 bolt. Sold individually, 4 per car. part #20408-S

Reproduction intake manifold bolts for the Mercury Cougar Eliminator or the Ford BOSS Mustang equipped with the 302 BOSS engine. These units are sold individually.Replaces Ford part # 56146-S.

Reproduction caliper bolt from AMK Grade 8 hex bolt. 2 bolts per caliper, sold individually. 7/16-14 x 1-5/8". These bolts hold the two halves together on the four piston Kelsey-Hayes calipers. Fits Kelsey-Hayes installed, 4 piston disc brake calipers used by Ford 1966-67.Replaces Ford part # 378225-S.