Bumpers & Trim

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

This bolt is what adjusts your headlamp cover height. Many people do not know they can rid themselves of that droopy eye look (misaligned grille) by placing new rubber pads on the heads of these bolts and adjusting them. Four required per car, sold individually. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

This bolt is what adjusts your headlamp cover height. Rare find to still have an original rubber bumper in place that is not compressed or cracked. Four required per car, sold individually. Check out this video

Spring that holds the headlight trim ring on each headlamp to the grille. 4 springs per car, sold individually.Ford number C6AZ-13031-C.

Used anti rattle pad for the stone guard on the Mercury Cougar. This unit is for the 1970 Mercury Cougar specifically and will not fit any other year. These pads must be used with the 1970 Cougar front bumper mounting brackets and the brackets can identified with the square cut window for mounting this pad. Our pad is sold individually and two are required per car.

Anti rattle pad that hooks onto the top edge of the front bumper brackets. These created a soft cushion to prevent the stone deflector from coming into contact with the bumper bracket. These were originally held on with friction tape, same type of tape that Ford used to wrap the wiring harnesses. Sold individually, two needed per car.

Captured washer, or spinning washer nut for attaching the headlamp motors or vacuum actuators on the 1969-70 Mercury Cougar. All models, Standard Hard Top, XR7, and Eliminator. Two needed per car, sold individually.

We are excited to bring these new reproduction chrome backup light bezels for the 1969 and 1970 Mercury Cougar to the market. The sockets, pigtails and lenses are not included so you will need to gently remove your originals and install them in these bezels. You can find the lenses here.

We are excited to bring these new reproduction assemblies for the backup lights for the 1969 and 1970 Mercury Cougar to the market. Includes a pair of bezels with lenses and gaskets. The sockets and pigtails are not included so you will need to gently remove your originals and install them in these bezels.NOTE: We've been informed that the reproduction lenses will need a bit of filing and sanding to properly fit into these reproduction bezels.

NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight bend in the chromed quarter piece, whereas the early version is straight (see photo above). Made With Exact Materials As Original. Eight piece kit that includes inner and outer belt-line, enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them...

Best used bezel we can find from a Western parts car. "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13064, and D3WY-13064-B.

Restored driver (left hand) side headlight bezel moulding for any 1971-72 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the core charge...

Restored driver (left hand) side headlight bezel moulding for any 1973 Mercury Cougar. Chromed only, detail black painted portions not completed. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had...

Best used bezel we can find from a Western parts car "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.

Best used bezel we can find from a Western parts car. "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13052 and D3WY-13064-A.

Restored passenger (right hand) side headlight bezel moulding for any 1971-72 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the core...

Restored passenger (right hand) side headlight bezel moulding for any 1973 Mercury Cougar.  Chromed only, detail black painted portions not completed. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored...

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13064, and D3WY-13064-B.

Driver side left hand headlight door. We have many good used head light doors in stock, give us a ring!

New Old Stock 1973 Mercury Cougar Driver side, headlight door.  Casting number reads D3WB-13064. Ford part number D3WY-13064-B

Driver side headlight door. If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four Phillips...

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13052 and D3WY-13064-A.

Driver side headlight door. New Old Stock.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The...

Passenger side right hand headlight door. We have many good used head light doors in stock, give us a ring! Casting number reads D1WB-13052. Ford part number D1WY-13064-A Check out this video

New Old Stock 1973 Mercury Cougar Passenger side, headlight door.  Casting number reads D3WB-13052. Ford part number D3WY-13064-A

Passenger side headlight door.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the passenger side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four...

Incorrect chrome finish (supposed to be satin not chrome) Mustang part that requires modification to make the metal XR7 insert fit. This is the only new alternative to your broken bezel, we sometimes get in an original that just needs paint. This unit will also fit the Cyclone, Montego, and many other Mercurys and Fords. Replaces Ford part # C8ZZ-3D572-A.

This is the correct horn panel bezel for all 1968 standard model Cougar steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Please see related for XR7 model bezel. Ford part number C8AA-3D754-A.

This is the correct horn panel bezel for all 1968 Cougar XR7 steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Unique to the XR7, identified by having the grey inserts. Please see related for standard model bezel.Ford part number C8AA-3D754-A. * Note - Will not work on standard model Cougar pads without removal of the inserts.

License to rear bumper spacer used on all 1973 Cougars. Usually this item is badly cracked or missing. This is a show quality used part for those that are concerned about less than obvious detail items.NOTE: The difference between the 71-72 version and this 73 version is that the 73 did not have a casting number and the earlier year versions did.

Good used driver side (left hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. If you are planning on sending in cores to be restored this is the level you would want to start with. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Ford part # C9WB-13504 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem?...

Good used driver side (left hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. If you are planning on sending in cores to be restored this is the level you would want to start with. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Driver side chrome tail light door or bezel. Ford part # D0WB-13504-A for the driver side. *NOTE* Need...

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts.Ford part # C9WB-13449 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts. Ford part # D0WB-13504-A for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great...

NOS driver side (left hand) taillight bezel for the Mercury Cougar.Ford part # C9WY-13489. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send...

New Old Stock 1973 Mercury Cougar driver side tail light bezel, NOS. Ford part number D3WY-13489-B.

Restored driver side (left hand) 1971-72 Mercury Cougar taillight bezel. These have been restored with the correct bright dipped, anodize finish. You will have to do the finish, detail painting. Note that in the buffing process the ridges are worn down noticeably on the horizontal bars. Mercury part number D1WY-13489-B. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a used or core D1WY-13489-B trim. Call 503-463-1130 if you have any...

Restored driver side (left hand) 1973 Mercury Cougar taillight bezel. These have been restored with the correct bright dipped, anodize finish. You will have to do the finish, detail painting. Note that in the buffing process the ridges are worn down noticeably on the horizontal bars. Mercury part number D3WY-13489-B. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a used or core D3WY-13489-B trim. Call 503-463-1130 if you have any...

Used driver side 1971-72 Mercury Cougar tail light bezel. Minor blemishes, perfect driver quality. Mercury part number D1WY-13489-B. No Core required. Check out this LED Comparison video

Used driver side 1973 Mercury Cougar tail light bezel. Minor blemishes, perfect driver quality. Mercury part number D3WY-13489-B. No Core required. Check out this LED Comparison video

Grade "A" passenger side (left hand) bezel with no pitting, ready to install and use as-is. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check out this video ...

Good used passenger side (right hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. If you are planning on sending in cores to be restored this is the level you would want to start with. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Passenger side chrome tail light door or bezel. Ford part # D0WB-13449-A for the passenger side....