Grille

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

This bolt is what adjusts your headlamp cover height. Many people do not know they can rid themselves of that droopy eye look (misaligned grille) by placing new rubber pads on the heads of these bolts and adjusting them. Four required per car, sold individually. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

This bolt is what adjusts your headlamp cover height. Rare find to still have an original rubber bumper in place that is not compressed or cracked. Four required per car, sold individually. Check out this video

Spring that holds the headlight trim ring on each headlamp to the grille. 4 springs per car, sold individually.Ford number C6AZ-13031-C.

Captured washer, or spinning washer nut for attaching the headlamp motors or vacuum actuators on the 1969-70 Mercury Cougar. All models, Standard Hard Top, XR7, and Eliminator. Two needed per car, sold individually.

Best used bezel we can find from a Western parts car. "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13064, and D3WY-13064-B.

Best used bezel we can find from a Western parts car "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.

Best used bezel we can find from a Western parts car. "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13052 and D3WY-13064-A.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13064, and D3WY-13064-B.

Driver side left hand headlight door. We have many good used head light doors in stock, give us a ring!

New Old Stock 1973 Mercury Cougar Driver side, headlight door.  Casting number reads D3WB-13064. Ford part number D3WY-13064-B

Driver side headlight door. If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four Phillips...

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13052 and D3WY-13064-A.

Driver side headlight door. New Old Stock.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The...

Passenger side right hand headlight door. We have many good used head light doors in stock, give us a ring! Casting number reads D1WB-13052. Ford part number D1WY-13064-A Check out this video

New Old Stock 1973 Mercury Cougar Passenger side, headlight door.  Casting number reads D3WB-13052. Ford part number D3WY-13064-A

Passenger side headlight door.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the passenger side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four...

Grade A driver side (left hand) chrome bezel that wraps around the outside of the front turn signal lens on the 1973 Mercury Cougar. Grade A has excellent used chrome, may have small amount of freckling in the chrome due to age and thin original plating.Ford part # D3WB-13237-AB.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Grade B driver side (right hand) chrome bezel that wraps around the outside of the front turn signal lens on the 1973 Mercury Cougar. Grade B has driver quality chrome, and will have pitting and or imperfections from 40 plus years of use. Ford part # D3WB-13237-AB.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

Chrome driver side (left hand) bezel that wraps around the outside of the front turn signal lens on the 1973 Mercury Cougar. This bezel will be blemished. Blemishes could include cracks, pitting, or bends. Will not be missing any pieces. Ford part # D3WB-13237-AA.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

New Old Stock NOS driver side front turn signal bezel for any 1973 Mercury Cougar. Ford part number  D3WY-13212-A, casting number D3WB-13237-AB.

Grade A passenger side (right hand) chrome bezel that wraps around the outside of the front turn signal lens on the 1973 Mercury Cougar. Grade A has excellent used chrome, may have small amount of freckling in the chrome due to age and thin original plating.Ford part # D3WB-13236-AB.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid...

Chrome passenger side (right hand) bezel that wraps around the outside of the front turn signal lens on the 1971 or 1972 Mercury Cougar. This bezel will be blemished. Blemishes could include cracks, pitting, or bends. Will not be missing any pieces. Ford part # D1WB-13236-AA.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Grade B passenger side (right hand) chrome bezel that wraps around the outside of the front turn signal lens on the 1973 Mercury Cougar. Grade B has driver quality chrome, and will have pitting and or imperfections from 40 plus years of use. Ford part # D3WB-13236-AB.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

New Old Stock NOS passenger side front turn signal bezel for any 1973 Mercury Cougar.Ford part number  D3WY-13210-A, casting number D3WB-13236-AB.

Reproduction Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang.If you're working on both sides of your grille, you will need two kits, one kit will do one half of the grille.

Reproduction Headlamp Housing Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang

Powder Coated. Replaces Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Used to mount the vacuum storage tank inside the driver fender, two required per car, sold individually. Exact same part as what is found on the 1968 Cougar just a slightly different clips is used for 1969. Cougar part number C8WY-13B008-A.

This is the flat topped rubber bumper that attaches to the top part of your center grille and keeps a small gap between the two panels to prevent paint chips. There were two versions of this bumper, one was this flat topped bumper, and the other had a rounded top. Find the round topped version here.

This little rubber part attaches to the top, flat part of your center grille and keeps a small gap between the two panels to prevent paint chips. This is actually an ash tray bumper but it is a decent substitute (a little smaller than the original) for the center grille bumper. The originals had a flat top as opposed to this bumper which has a rounded top. You can find the flat topped version here. ...

C9AZ-13A164-B Inner grille bushing, where the hidden headlight hinge pivots. Hole size is 3/4", shaft size is 1/2". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights.

Used outer bushing for the hinge pivots for the hide-away headlights on the Mercury Cougar. Hole size is 5/8", shaft size is 3/8". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights. Ford part # C9AZ-13A164-A. ...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

C9AZ-13B013-A Center section that connects to the vacuum motor on many 1969 Ford and Mercury cars with vacuum covered headlights. 1969 Mercury Cougar including XR7 and Eliminator. The center piece is offset to the left of center and the hook part that goes to the vacuum motor points down. 1969 and 1970 center shafts are not interchangeable. 1969 Ford LTD 1969 Galaxie and Galaxie XL 1969 Country Squire Wagons 1969 Mercury Marquis 1969 Mercury Brougham 1969 Marauder and X-100 1969 Colony Park...

D0WY-13B013-A Center section that connects to the vacuum motor on 1970 Mercury Cougar, including XR7 and Eliminator. The center piece is offset to the left of center and the hook part that goes to the vacuum motor points down.1969 and 1970 center shafts are not interchangeable.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This check valve is located in-line just behind your carburetor. To test it simply place it in your lips and try blowing through the side with the single port. You should be able to breath in and not breath out. If this valve is bad you will find the headlights opening up after the engine has been shut off on your 1969 - 1970 Cougars and your tilt away function not working correctly on your 1967 - 1970 Cougars equipped with a tilt column. A good working vacuum system should be able to...

Used 1968 Mercury Cougar GT-E horizontal grille bar clip or keeper for the center grille section. This is a rare find, limited to stock on hand.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Reproduction Center Grille Insert Background Decal for the 1967 and 1968 Mercury Cougar. This insert will need to be shaved down on 2 sides to fit correctly, do not force the insert into the grille, it will pooch up in the middle and not adhere correctly. The aluminum Mercury Man emblem can be popped out from the rear with a solid hit with a drift punch and hammer without causing damage. Check out our video, showing how to install this decal, along with some other handy grille restoration tips ...

Nice reproduction that is "almost" spot on. Of the two versions available this one has much more definition. When you put an original next to this reproduction you will notice the original has a more raised, defined face on the Mercury Man.