1967

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

This bolt is what adjusts your headlamp cover height. Many people do not know they can rid themselves of that droopy eye look (misaligned grille) by placing new rubber pads on the heads of these bolts and adjusting them. Four required per car, sold individually. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

This bolt is what adjusts your headlamp cover height. Rare find to still have an original rubber bumper in place that is not compressed or cracked. Four required per car, sold individually. Check out this video

Driver side headlight door. If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four Phillips...

Driver side headlight door. New Old Stock.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The...

Passenger side headlight door.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the passenger side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four...

This is the flat topped rubber bumper that attaches to the top part of your center grille and keeps a small gap between the two panels to prevent paint chips. There were two versions of this bumper, one was this flat topped bumper, and the other had a rounded top. Find the round topped version here.

This little rubber part attaches to the top, flat part of your center grille and keeps a small gap between the two panels to prevent paint chips. This is actually an ash tray bumper but it is a decent substitute (a little smaller than the original) for the center grille bumper. The originals had a flat top as opposed to this bumper which has a rounded top. You can find the flat topped version here. ...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This check valve is located in-line just behind your carburetor. To test it simply place it in your lips and try blowing through the side with the single port. You should be able to breath in and not breath out. If this valve is bad you will find the headlights opening up after the engine has been shut off on your 1969 - 1970 Cougars and your tilt away function not working correctly on your 1967 - 1970 Cougars equipped with a tilt column. A good working vacuum system should be able to...

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Reproduction Center Grille Insert Background Decal for the 1967 and 1968 Mercury Cougar. This insert will need to be shaved down on 2 sides to fit correctly, do not force the insert into the grille, it will pooch up in the middle and not adhere correctly. The aluminum Mercury Man emblem can be popped out from the rear with a solid hit with a drift punch and hammer without causing damage. Check out our video, showing how to install this decal, along with some other handy grille restoration tips ...

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. This kit consists of two electric actuator assemblies (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable than previous versions that utilized the Ford Probe motors and are...

This is a very nice reproduction that we have all needed for many years! You might want to buy a new Cougar walking cat emblem if you replace this background decal as it requires breaking the studs off your old emblem to get it off. Check out this video ...

Assembly required This high quality corral fits perfectly and the chrome plating is well beyond what Ford originally did. The mounting studs are placed in the exact position as original. We have offered the walking cat and black background for sometime now but the challenge has been getting your used corral (or rectangle frame) remounted after you break off the studs to remove the assembly. Replacing this emblem assembly is probably (for the money) the best way to improve the looks of the...

Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only designed to be installed once. Click on images to enlarge. The above is a very sought after collectible that was circulated back in 1967-1968. This picture above (From Jim Pinkerton) is of a pen...

Very rare to find one of these that has never been tapped in the slightest. We have a very limited quantity of grade A centers in stock. Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

The majority of our centers look like the rust free part you see pictured. They will need some minor body work before paint. We will not send you junk! Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Good used part with no pitting or obvious damage. Includes stamped steel metal mounting bracket attached to the backside. Cougar part numbers: C7WY-13A137-B (Headlamp exterior cover) C7WY-13A155-A (Headlamp hinge) Check out this video

Good used eyelid with no pitting or obvious damage and is for 1967 and early 1968 Cougars built prior 12/15/1967. Includes emblem and metal mounting plate. Ford part # C7WY-13A136-B (Headlamp exterior cover) C7WY-13A154-A (Headlamp hinge) Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford part...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford...

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

One of the most common problems with first-generation Cougars is droopy hidden headlight eyelids, which make the otherwise iconic front grille look like an eyesore. This inexpensive and easy to install kit provides stops for the eyelids to rest against in the closed position. It also provides some extra structural support to take some of the pressure off the built in bump stops. The vacuum actuators on these cars create extreme downward pressure at all times when running, causing the upper...

High quality reproduction of the chrome rectangular "corral" emblem surround for the passenger side grille / headlight cover on a 1967-68 Mercury Cougar. Unlike the original, which had the 4 studs peened over on the back side of the grille, this new one attaches with 4 clips (included). See also the background decal and walking cat emblem to make this a complete assembly. We also sell this as a complete kit. ...

Fits Standard and XR7 Check out this video

Used grade "A" driver side (left hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of large cracks, has good chrome with no pits or major scratches and is not severely warped. Hairline cracks will be present in the area of the painted...

Used grade "A" driver side (left hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and may have some minor cracking, but the chrome will not have pits, major scratches, and will not be severely warped. It will have a misalignment issue as they all do in the...

Used grade "C" driver side (left hand) grille section for use as a patch for those with a break in the section that continues to the fender. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair

Used grade "A" passenger side (right hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of large cracks, has good chrome with no pits or major scratches and is not severely warped.  Hairline cracks will be present in the area of the...

Used passenger side (right hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of pits or major scratches in the chrome and is not severely warped. It will have a misalignment issue as they all do in the portion on the outer most corner...

Used grade "C" Passenger side (right hand) grille section for use as a patch for those with a break in the section that continues to the fender. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair

This complete set of grille bars have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no scrapes so as to qualify for...

This used bracket kit is what is needed to mount the headlight vacuum storage tank inside the front of the driver side front fender. This kit differs from the 1970 kit only in the slightly different design of fasteners used.

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7OB-37B and "RL", There are four different versions used, but they are the same for the 1967 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-37-A. Right hand low beam holder. Ford part...

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up. If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much easier to find inner, high beam lamp distinguished by the number 1 at 12...

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7MB-17A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-17-A. Left hand high beam holder. Ford part # C7MB-17A ...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7OB-47B and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-47-A.  Ford part # C7OB-47B.